Cypress CY7C638xx, CY7C63310 manual ProtectBlock Parameters Name Address Description

Page 17

CY7C63310, CY7C638xx

Table 9-8. ProtectBlock Parameters

Name

Address

Description

KEY1

0,F8h

3Ah

 

 

 

KEY2

0,F9h

Stack Pointer value when SSC is

 

 

executed.

CLOCK

0,FCh

Clock divider used to set the write pulse

 

 

width.

DELAY

0,FEh

For a CPU speed of 12 MHz set to 56h.

 

 

 

9.5.6 EraseAll Function

The EraseAll function performs a series of steps that destroy the user data in the Flash macros and resets the protection block in each Flash macro to all zeros (the unprotected state). The EraseAll function does not affect the three hidden blocks above the protection block, in each Flash macro. The first of these four hidden blocks is used to store the protection table for its eight Kbytes of user data.

The EraseAll function begins by erasing the user space of the Flash macro with the highest address range. A bulk program of all zeros is then performed on the same Flash macro, to destroy all traces of the previous contents. The bulk program is followed by a second erase that leaves the Flash macro in a state ready for writing. The erase, program, erase sequence is then performed on the next lowest Flash macro in the address space if it exists. After the erase of the user space, the protection block for the Flash macro with the highest address range is erased. Following the erase of the protection block, zeros are written into every bit of the protection table. The next lowest Flash macro in the address space then has its protection block erased and filled with zeros.

The end result of the EraseAll function is that all user data in the Flash is destroyed and the Flash is left in an unprogrammed state, ready to accept one of the various write commands. The protection bits for all user data are also reset to the zero state

The parameter block values that must be set, besides the keys, are the CLOCK and DELAY values.

Table 9-9. EraseAll Parameters

Name

Address

Description

KEY1

0,F8h

3Ah

 

 

 

KEY2

0,F9h

Stack Pointer value when SSC is

 

 

executed.

CLOCK

0,FCh

Clock divider used to set the write pulse

 

 

width.

DELAY

0,FEh

For a CPU speed of 12 MHz set to 56h

 

 

 

9.5.7 TableRead Function

The TableRead function gives the user access to part specific data stored in the Flash during manufacturing. It also returns a Revision ID for the die (not to be confused with the Silicon ID).

Table 9-10. Table Read Parameters

Name

Address

Description

KEY1

0,F8h

3Ah

 

 

 

KEY2

0,F9h

Stack Pointer value when SSC is

 

 

executed.

BLOCKID

0,FAh

Table number to read.

 

 

 

The table space for the enCoRe II is simply a 64 byte row broken up into eight tables of eight bytes. The tables are numbered zero through seven. All user and hidden blocks in the CY7C638xx parts consist of 64 bytes.

An internal table (Table 0) holds the Silicon ID and returns the Revision ID. The Silicon ID is returned in SRAM, while the Revision and Family IDs are returned in the CPU_A and CPU_X registers. The Silicon ID is a value placed in the table by programming the Flash and is controlled by Cypress Semicon- ductor Product Engineering. The Revision ID is hard coded into the SROM and also redundantly placed in SROM Table 1. This is discussed in more detail later in this section.

SROM Table 1 holds Family/Die ID and Revision ID values for the device and returns a one-byte internal revision counter. The internal revision counter starts out with a value of zero and is incremented when one of the other revision numbers is not incre- mented. It is reset to zero when one of the other revision numbers is incremented. The internal revision count is returned in the CPU_A register. The CPU_X register is always set to FFh when Table 1 is read. The CPU_A and CPU_X registers always return a value of FFh when Tables 2-7 are read. The BLOCKID value, in the parameter block, indicates which table must be returned to the user. Only the three least significant bits of the BLOCKID parameter are used by TableRead function for enCoRe II devices. The upper five bits are ignored. When the function is called, it transfers bytes from the table to SRAM addresses F8h–FFh.

The M8C’s A and X registers are used by the TableRead function to return the die’s Revision ID. The Revision ID is a 16-bit value hard coded into the SROM that uniquely identifies the die’s design.

The return values for corresponding Table calls are tabulated as shown in Table 9-11on page 17

Table 9-11. Return values for Table Read

Table Number

 

Return Value

A

 

X

 

 

0

Revision ID

 

Family ID

 

 

 

1

Internal Revision Counter

0xFF

 

 

 

 

2-7

0xFF

 

0xFF

 

 

 

 

Document 38-08035 Rev. *K

Page 17 of 83

[+] Feedback

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Applications FeaturesCypress Semiconductor Corporation 198 Champion Court San Jose, CA Document 38-08035 Rev. *K Revised December 08Gpio Logic Block DiagramConventions IntroductionPinouts Die Pad Summary Pad Number Pad Name Microns Gpio Port 1 bit 1/USB D- 1 If this pin is used as a Pin DescriptionGpio Port 1 bit 0/USB D+ 1 If this pin is used as a No connect CPU ArchitectureSupply GroundFlags Register CPU RegistersAddressing Modes Source Indexed Opcode Operand Source Direct Opcode Operand10. Destination Direct Opcode Operand Destination Indexed13. Destination Indexed Source Immediate Opcode Operand 12. Destination Direct Source Immediate Opcode Operand14. Destination Direct Source Direct Opcode Operand 15. Source Indirect Post Increment Opcode OperandInstruction Set Summary Sorted Numerically by Opcode Order2 Instruction Set SummaryFlash Program Memory Organization Memory OrganizationPOR/LVD INT0 EP0 EP1 EP2Flash Data Memory OrganizationSrom Stack begins here and grows upwardSrom Function Parameters Variable Name Sram Address Srom Function DescriptionsSrom Return Codes Description ReadBlock Parameters Name Address DescriptionWriteBlock Parameters Name Address Description Protection Modes Settings Description MarketingEraseBlock Parameters Name Address Description Block Block nEraseAll Parameters Name Address Description ProtectBlock Parameters Name Address Description10. Table Read Parameters Name Address Description 11. Return values for Table Read Table Number Return ValueSrom Table 12. Checksum Parameters Name Address Description ClockingChecksum Function Clock Block Diagram Bit 40 Gain Clock Architecture DescriptionIosc Trim Iosctr 0x34 R/W Bit 41 Reserved CPU/USB Clock Config Cpuclkcr 0x30 R/WLposc Trim Lposctr 0x36 R/W Bit 76 Reserved Bit 5 No Buzz OSC Control 0 OSCCR0 0x1E0 R/WTimer Clock Config Tmrclkcr 0x31 R/W USB Osclock Clock Configuration Osclckcr 0x39 R/WBit 72 Reserved = TcapclkCou nte r Terru pt Ntro ller Document 38-08035 Rev. *K Interval Timer Clock ItmrclkTimer Capture Clock Tcapclk Clock IO Config Clkiocr 0x32 R/W CPU Clock During Sleep ModeReset Power on Reset Sleep ModeWatchdog Timer Reset Reset Watchdog Timer Reswdt 0xE3 WWake up Sequence Sleep SequenceWake Up Timing Low Power in Sleep ModeLow Voltage Control Register Lvdcr 0x1E3 R/W Low Voltage Detect ControlBit 76 Reserved Bit 54 PORLEV10 Bit 20 VM20 LVD Trip Point V Min Point V Typ Point V MaxBit 72 Reserved Bit 1 LVD Voltage Monitor Comparators Register Vltcmp 0x1E4 RECO Trim Register ECO Ecotr 0x1EB R/WP0 Data Register P0DATA0x00 R/W General Purpose IO Gpio PortsPort Data Registers P3 Data Register P3DATA 0x03 R/W P1 Data Register P1DATA 0x01 R/WP2 Data Register P2DATA 0x02 R/W Gpio Port Configuration P0.1/CLKOUT Configuration P01CR 0x06 R/W P0.0/CLKIN Configuration P00CR 0x05 R/WP0.5/TIO0 P0.6/TIO1 Configuration P05CR-P06CR 0x0A-0x0B R/W P0.2/INT0-P0.4/INT2 Configuration P02CR-P04CR 0x07-0x09 R/W10. P1.0/D+ Configuration P10CR 0x0D R/W P0.7 Configuration P07CR 0x0C R/W11. P1.1/D- Configuration P11CR 0x0E R/W 12. P1.2 Configuration P12CR 0x0F R/W14. P1.4-P1.6 Configuration P14CR-P16CR 0x11-0x13 R/W 13. P1.3 Configuration P13CR 0x10 R/W15. P1.7 Configuration P17CR 0x14 R/W 16. P2 Configuration P2CR 0x15 R/WSerial Peripheral Interface SPI 17. P3 Configuration P3CR 0x16 R/WSPI Data Register SPI Data Register Spidata 0x3C R/WSPI Configure Register Sclk Ssel DAT a SPI Interface PinsSPI Mode Timing vs. LSB First, Cpol and Cpha Free Running Timer Low order Byte Frtmrl 0x20 R/W Timer RegistersFree Running Timer High-order Byte Frtmrh 0x21 R/W RegistersTimer Capture 1 Rising TIO1R 0x23 R/W Timer Capture 0 Rising TIO0R 0x22 R/WTimer Capture 0 Falling TIO0F 0x24 R/W Timer Capture 1 Falling TIO1F 0x25 R/WBit 74 Reserved Programmable Interval Timer High Pitmrh 0x27 RProgrammable Interval Reload Low Pirl 0x28 R/W 10. Programmable Interval Reload High Pirh 0x29 R/WBit 20 Reserved Timer Capture11. Timer Configuration Tmrcr 0x2A R/W 13. Capture Interrupt Status Tcapints 0x2C R/W 12. Capture Interrupt Enable Tcapinte 0x2B R/WTimer Functional Sequence Diagram Bit Free Running Counter Loading Timing Diagram Architectural Description Interrupt ControllerInterrupt Trigger Conditions Interrupt ProcessingInterrupt Latency PCH PC158 is cleared to zeroInterrupt Clear 0 INTCLR0 0xDA R/W Interrupt RegistersInterrupt Clear 1 INTCLR1 0xDB R/W Interrupt Clear 2 INTCLR2 0xDC R/WBit 60 Reserved Interrupt Mask 2 INTMSK2 0xDF R/W Bit 7 Enable Software Interrupt EnswintInterrupt Mask 3 INTMSK3 0xDE R/W Interrupt Mask 1 INTMSK1 0xE1 R/W Interrupt Vector Clear Register Intvc 0xE2 R/W Interrupt Mask 0 INTMSK0 0xE0 R/WVreg Control Register Vregcr 0x73 R/W Regulator OutputVreg Control USB Transceiver Configure Register Usbxcr 0x74 R/W USB Transceiver ConfigurationUSB/PS2 Transceiver USB Serial Interface Engine SIEUSB Device Address USB DeviceEndpoint 0, 1, and 2 Count USB Device Address Usbcr 0x40 R/WBit 30 Mode Endpoint 0 ModeEndpoint 0 Mode EP0MODE 0x44 R/W Endpoint 1 and 2 Mode EP1MODE EP2MODE 0x45, 0x46 R/W Endpoint 1 and 2 ModeBit 7 Stall Endpoint 0 Data EP0DATA 0x50-0x57 R/WMode Column USB Mode TablesEncoding Column Endpoint 2 Data EP2DATA 0x60-0x67 R/WSETUP, IN, and OUT Columns Details of Mode for Differing Traffic ConditionsCount Fifo Register Summary Addr Name DefaultTmrcr Intvc Voltage vs CPU Frequency Characteristics Voltage Vs CPU Frequency CharacteristicsAbsolute Maximum Ratings DC CharacteristicsDetect 3V RegulatorGeneral Purpose IO Interface AC CharacteristicsParameter Description Conditions Min Typical Max Unit Clock CpuclkSPI Timing Non-USB Mode Driver CharacteristicsUSB Data Timing Clock Timing Gpio Timing DiagramDifferential Data Lines SCK CPOL=0 SCK CPOL=0 SCK CPOL=1 Package Handling Ordering InformationPin 300-Mil Molded DIP P1 Package DiagramsPin 300-Mil Molded DIP P3 Pin 300-Mil Soic S13 Pin QFN Package Document History Updated part numbers in the header Added block diagrams and timing diagramsRemoved 638xx die diagram and die form pad assignment Removed Gpio port 4 configuration detailsCMCC/PYRS VGT/AESAUSB Sales, Solutions, and Legal InformationWorldwide Sales and Design Support Products PSoC Solutions

CY7C638xx, CY7C63310 specifications

The Cypress CY7C63310 and CY7C638xx series are advanced USB microcontrollers designed for various applications requiring reliable performance and flexibility. These chips are notable for their integration of several key technologies, enabling developers to create innovative electronic designs effortlessly.

The CY7C63310 is a part of the Cypress USB microcontroller family that boasts a fully integrated 8051-compatible microprocessor core. This architecture allows for efficient execution of high-level programming languages like C, enhancing code development efforts. The microcontroller supports USB 2.0 full-speed operation, allowing for high data transfer rates of up to 12 Mbps, essential for applications involving data communication.

One of the standout features of the CY7C63310 is its programmable GPIO (General-Purpose Input/Output) pins, which provide developers with the versatility to configure these pins as inputs, outputs, or alternate functions. This flexibility is particularly advantageous in applications where custom interfaces are essential, such as human-machine interfaces, sensor control, and USB peripherals.

Moreover, the CY7C638xx series presents an even broader array of features. These devices typically support various memory configurations, enabling designers to select from different on-chip RAM and flash memory options. This variety empowers projects requiring a mix of program and data storage capabilities, all while ensuring that performance remains optimal.

Both the CY7C63310 and CY7C638xx series leverage Cypress's EZ-USB technology, which simplifies the process of USB interface implementation. The EZ-USB architecture minimizes the effort associated with USB protocol complexity, allowing developers to focus on the core functionality of their applications.

These microcontrollers also incorporate features such as low-power operation, making them ideal for battery-operated devices. With various power management modes, designers can optimize energy consumption according to the specific needs of their applications.

In terms of connectivity, these chips support multiple interface standards, including SPI, I2C, and UART. These capabilities ensure that developers can easily interface with other components and systems, enhancing the overall utility of the microcontroller.

In summary, the Cypress CY7C63310 and CY7C638xx microcontrollers stand out for their robust features, including integrated USB functionality, flexible GPIO options, and support for various communication protocols. These attributes make them suitable for a wide range of applications, from consumer electronics to industrial automation, making them an excellent choice for developers seeking reliable and adaptable microcontroller solutions.
Top Page Image Contents