Cypress CY7C638xx, CY7C63310 manual SPI Configure Register

Page 41

CY7C63310, CY7C638xx

15.2 SPI Configure Register

Table 15-2. SPI Configure Register (SPICR) [0x3D] [R/W]

Bit #

7

6

5

 

4

3

2

1

 

0

Field

Swap

LSB First

 

Comm Mode

CPOL

CPHA

 

SCLK Select

Read/Write

R/W

R/W

R/W

 

R/W

R/W

R/W

R/W

 

R/W

Default

0

0

0

 

0

0

0

0

 

0

 

 

 

 

 

 

 

 

 

 

 

Bit 7: Swap

0 = Swap function disabled.

1 = The SPI block swaps its use of SMOSI and SMISO. This is useful in implementing single wire communications similar to SPI. Bit 6: LSB First

0 = The SPI transmits and receives the MSB (Most Significant Bit) first.

1 = The SPI transmits and receives the LSB (Least Significant Bit) first. Bit [5:4]: Comm Mode [1:0]

0 0: All SPI communication disabled.

0 1: SPI master mode

1 0: SPI slave mode

1 1: Reserved

Bit 3: CPOL

This bit controls the SPI clock (SCLK) idle polarity. 0 = SCLK idles low

1 = SCLK idles high

Bit 2: CPHA

The Clock Phase bit controls the phase of the clock on which data is sampled. Table 15-4on page 42 shows the timing for the various combinations of LSB First, CPOL, and CPHA.

Bit [1:0]: SCLK Select

This field selects the speed of the master SCLK. When in master mode, SCLK is generated by dividing the base CPUCLK.

Note for Comm Modes 01b or 10b (SPI Master or SPI Slave)

When configured for SPI, (SPI Use = 1 Table 14-14on page 39), the input/output direction of pins P1.3, P1.5, and P1.6 is set automatically by the SPI logic. However, pin P1.4's input/output direction is NOT automatically set; it must be explicitly set by firmware. For SPI Master mode, pin P1.4 must be configured as an output; for SPI Slave mode, pin P1.4 must be configured as an input.

Table 15-3. SPI SCLK Frequency

SCLK

CPUCLK

SCLK Frequency when CPUCLK =

Select

Divisor

12 MHz

24 MHz

00

6

2 MHz

4 MHz

 

 

 

 

01

12

1 MHz

2 MHz

 

 

 

 

10

48

250 kHz

500 kHz

 

 

 

 

11

96

125 kHz

250 kHz

 

 

 

 

Document 38-08035 Rev. *K

Page 41 of 83

[+] Feedback

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Applications FeaturesCypress Semiconductor Corporation 198 Champion Court San Jose, CA Document 38-08035 Rev. *K Revised December 08Gpio Logic Block DiagramConventions IntroductionPinouts Die Pad Summary Pad Number Pad Name Microns Gpio Port 1 bit 1/USB D- 1 If this pin is used as a Pin DescriptionGpio Port 1 bit 0/USB D+ 1 If this pin is used as a No connect CPU ArchitectureSupply GroundFlags Register CPU RegistersAddressing Modes Source Indexed Opcode Operand Source Direct Opcode Operand10. Destination Direct Opcode Operand Destination Indexed13. Destination Indexed Source Immediate Opcode Operand 12. Destination Direct Source Immediate Opcode Operand14. Destination Direct Source Direct Opcode Operand 15. Source Indirect Post Increment Opcode OperandInstruction Set Summary Sorted Numerically by Opcode Order2 Instruction Set SummaryFlash Program Memory Organization Memory OrganizationPOR/LVD INT0 EP0 EP1 EP2Flash Data Memory OrganizationSrom Stack begins here and grows upwardSrom Function Parameters Variable Name Sram Address Srom Function DescriptionsSrom Return Codes Description ReadBlock Parameters Name Address DescriptionWriteBlock Parameters Name Address Description Protection Modes Settings Description MarketingEraseBlock Parameters Name Address Description Block Block nEraseAll Parameters Name Address Description ProtectBlock Parameters Name Address Description10. Table Read Parameters Name Address Description 11. Return values for Table Read Table Number Return ValueSrom Table 12. Checksum Parameters Name Address Description ClockingChecksum Function Clock Block Diagram Bit 40 Gain Clock Architecture DescriptionIosc Trim Iosctr 0x34 R/W Bit 41 Reserved CPU/USB Clock Config Cpuclkcr 0x30 R/WLposc Trim Lposctr 0x36 R/W Bit 76 Reserved Bit 5 No Buzz OSC Control 0 OSCCR0 0x1E0 R/WTimer Clock Config Tmrclkcr 0x31 R/W USB Osclock Clock Configuration Osclckcr 0x39 R/WBit 72 Reserved = TcapclkCou nte r Terru pt Ntro ller Document 38-08035 Rev. *K Interval Timer Clock ItmrclkTimer Capture Clock Tcapclk Clock IO Config Clkiocr 0x32 R/W CPU Clock During Sleep ModeReset Power on Reset Sleep ModeWatchdog Timer Reset Reset Watchdog Timer Reswdt 0xE3 WWake up Sequence Sleep SequenceWake Up Timing Low Power in Sleep ModeLow Voltage Control Register Lvdcr 0x1E3 R/W Low Voltage Detect ControlBit 76 Reserved Bit 54 PORLEV10 Bit 20 VM20 LVD Trip Point V Min Point V Typ Point V MaxBit 72 Reserved Bit 1 LVD Voltage Monitor Comparators Register Vltcmp 0x1E4 RECO Trim Register ECO Ecotr 0x1EB R/WP0 Data Register P0DATA0x00 R/W General Purpose IO Gpio PortsPort Data Registers P3 Data Register P3DATA 0x03 R/W P1 Data Register P1DATA 0x01 R/WP2 Data Register P2DATA 0x02 R/W Gpio Port Configuration P0.1/CLKOUT Configuration P01CR 0x06 R/W P0.0/CLKIN Configuration P00CR 0x05 R/WP0.5/TIO0 P0.6/TIO1 Configuration P05CR-P06CR 0x0A-0x0B R/W P0.2/INT0-P0.4/INT2 Configuration P02CR-P04CR 0x07-0x09 R/W10. P1.0/D+ Configuration P10CR 0x0D R/W P0.7 Configuration P07CR 0x0C R/W11. P1.1/D- Configuration P11CR 0x0E R/W 12. P1.2 Configuration P12CR 0x0F R/W14. P1.4-P1.6 Configuration P14CR-P16CR 0x11-0x13 R/W 13. P1.3 Configuration P13CR 0x10 R/W15. P1.7 Configuration P17CR 0x14 R/W 16. P2 Configuration P2CR 0x15 R/WSerial Peripheral Interface SPI 17. P3 Configuration P3CR 0x16 R/WSPI Data Register SPI Data Register Spidata 0x3C R/WSPI Configure Register Sclk Ssel DAT a SPI Interface PinsSPI Mode Timing vs. LSB First, Cpol and Cpha Free Running Timer Low order Byte Frtmrl 0x20 R/W Timer RegistersFree Running Timer High-order Byte Frtmrh 0x21 R/W RegistersTimer Capture 1 Rising TIO1R 0x23 R/W Timer Capture 0 Rising TIO0R 0x22 R/WTimer Capture 0 Falling TIO0F 0x24 R/W Timer Capture 1 Falling TIO1F 0x25 R/WBit 74 Reserved Programmable Interval Timer High Pitmrh 0x27 RProgrammable Interval Reload Low Pirl 0x28 R/W 10. Programmable Interval Reload High Pirh 0x29 R/WBit 20 Reserved Timer Capture11. Timer Configuration Tmrcr 0x2A R/W 13. Capture Interrupt Status Tcapints 0x2C R/W 12. Capture Interrupt Enable Tcapinte 0x2B R/WTimer Functional Sequence Diagram Bit Free Running Counter Loading Timing Diagram Architectural Description Interrupt ControllerInterrupt Trigger Conditions Interrupt ProcessingInterrupt Latency PCH PC158 is cleared to zeroInterrupt Clear 0 INTCLR0 0xDA R/W Interrupt RegistersInterrupt Clear 1 INTCLR1 0xDB R/W Interrupt Clear 2 INTCLR2 0xDC R/WBit 60 Reserved Interrupt Mask 2 INTMSK2 0xDF R/W Bit 7 Enable Software Interrupt EnswintInterrupt Mask 3 INTMSK3 0xDE R/W Interrupt Mask 1 INTMSK1 0xE1 R/W Interrupt Vector Clear Register Intvc 0xE2 R/W Interrupt Mask 0 INTMSK0 0xE0 R/WVreg Control Register Vregcr 0x73 R/W Regulator OutputVreg Control USB Transceiver Configure Register Usbxcr 0x74 R/W USB Transceiver ConfigurationUSB/PS2 Transceiver USB Serial Interface Engine SIEUSB Device Address USB DeviceEndpoint 0, 1, and 2 Count USB Device Address Usbcr 0x40 R/WBit 30 Mode Endpoint 0 ModeEndpoint 0 Mode EP0MODE 0x44 R/W Endpoint 1 and 2 Mode EP1MODE EP2MODE 0x45, 0x46 R/W Endpoint 1 and 2 ModeBit 7 Stall Endpoint 0 Data EP0DATA 0x50-0x57 R/WMode Column USB Mode TablesEncoding Column Endpoint 2 Data EP2DATA 0x60-0x67 R/WSETUP, IN, and OUT Columns Details of Mode for Differing Traffic ConditionsCount Fifo Register Summary Addr Name DefaultTmrcr Intvc Voltage vs CPU Frequency Characteristics Voltage Vs CPU Frequency CharacteristicsAbsolute Maximum Ratings DC CharacteristicsDetect 3V RegulatorGeneral Purpose IO Interface AC CharacteristicsParameter Description Conditions Min Typical Max Unit Clock CpuclkSPI Timing Non-USB Mode Driver CharacteristicsUSB Data Timing Clock Timing Gpio Timing DiagramDifferential Data Lines SCK CPOL=0 SCK CPOL=0 SCK CPOL=1 Package Handling Ordering InformationPin 300-Mil Molded DIP P1 Package DiagramsPin 300-Mil Molded DIP P3 Pin 300-Mil Soic S13 Pin QFN Package Document History Updated part numbers in the header Added block diagrams and timing diagramsRemoved 638xx die diagram and die form pad assignment Removed Gpio port 4 configuration detailsCMCC/PYRS VGT/AESAUSB Sales, Solutions, and Legal InformationWorldwide Sales and Design Support Products PSoC Solutions

CY7C638xx, CY7C63310 specifications

The Cypress CY7C63310 and CY7C638xx series are advanced USB microcontrollers designed for various applications requiring reliable performance and flexibility. These chips are notable for their integration of several key technologies, enabling developers to create innovative electronic designs effortlessly.

The CY7C63310 is a part of the Cypress USB microcontroller family that boasts a fully integrated 8051-compatible microprocessor core. This architecture allows for efficient execution of high-level programming languages like C, enhancing code development efforts. The microcontroller supports USB 2.0 full-speed operation, allowing for high data transfer rates of up to 12 Mbps, essential for applications involving data communication.

One of the standout features of the CY7C63310 is its programmable GPIO (General-Purpose Input/Output) pins, which provide developers with the versatility to configure these pins as inputs, outputs, or alternate functions. This flexibility is particularly advantageous in applications where custom interfaces are essential, such as human-machine interfaces, sensor control, and USB peripherals.

Moreover, the CY7C638xx series presents an even broader array of features. These devices typically support various memory configurations, enabling designers to select from different on-chip RAM and flash memory options. This variety empowers projects requiring a mix of program and data storage capabilities, all while ensuring that performance remains optimal.

Both the CY7C63310 and CY7C638xx series leverage Cypress's EZ-USB technology, which simplifies the process of USB interface implementation. The EZ-USB architecture minimizes the effort associated with USB protocol complexity, allowing developers to focus on the core functionality of their applications.

These microcontrollers also incorporate features such as low-power operation, making them ideal for battery-operated devices. With various power management modes, designers can optimize energy consumption according to the specific needs of their applications.

In terms of connectivity, these chips support multiple interface standards, including SPI, I2C, and UART. These capabilities ensure that developers can easily interface with other components and systems, enhancing the overall utility of the microcontroller.

In summary, the Cypress CY7C63310 and CY7C638xx microcontrollers stand out for their robust features, including integrated USB functionality, flexible GPIO options, and support for various communication protocols. These attributes make them suitable for a wide range of applications, from consumer electronics to industrial automation, making them an excellent choice for developers seeking reliable and adaptable microcontroller solutions.
Top Page Image Contents