Briggs & Stratton 71021, 71020, 71019, 71018 manual Important Safety Instructions

Page 4

Save These Instructions

Important Safety Instructions

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

The safety alert symbol () is used with a signal word (DANGER, CAUTION, WARNING), a pictorial and/or a safety message to alert you to hazards. DANGER indicates a hazard which, if not avoided, will result in death or serious injury. WARNING indicates a hazard which, if not avoided, could result in death or serious injury. CAUTION indicates a hazard which, if not avoided, might result in minor or moderate injury. NOTICE indicates a situation that could result in equipment damage. Follow safety messages to avoid or reduce the risk of injury or death.

The manufacturer cannot possibly anticipate every possible circumstance that might involve a hazard. The warnings in this manual, and the tags and decals affixed to the unit are, therefore, not all-inclusive. If you use a procedure, work method or operating technique that the manufacturer does not specifically recommend, you must satisfy yourself that it is safe for you and others. You must also make sure that the procedure, work method or operating technique that you choose does not render the transfer switch unsafe.

WARNING

Failure to properly ground transfer switch can result in electrocution.

•DO NOT touch bare wires or receptacles.

•DO NOT use transfer switch with worn, frayed, bare or otherwise damaged wiring.

•DO NOT handle electrical cords while standing in water, while barefoot, or while hands or feet are wet.

•If you must work around a unit while it is operating, stand on an insulated dry surface to reduce shock hazard.

•DO NOT allow unqualified persons or children to operate or service transfer switch.

•In case of an accident caused by electrical shock, immediately shut down the source of electrical power and contact local authorities. Avoid direct contact with the victim.

WARNING

Transfer Switch contains hazardous voltage that can cause personal injury or death.

•Despite the safe design of the transfer switch, operating this equipment imprudently, neglecting its maintenance or being careless can cause possible injury or death.

WARNING

Only qualified electricians should attempt installation of this system, which must strictly comply with applicable codes, standards and regulations.

WARNING

Low voltage wire cannot be installed in same conduit as power voltage wiring.

•Failure to follow above warning could cause personal injury, damage and/or malfunction of equipment.

NOTICE

Improper treatment of transfer switch can damage it and shorten its life.

•Use transfer switch only for intended uses.

•If you have questions about intended use, ask dealer or contact Briggs and Stratton Power Products.

•Do not expose transfer switch to excessive moisture, dust, dirt, or corrosive vapors.

•Remain alert at all times while working on this equipment. Never work on the equipment when you are physically or mentally fatigued.

•If connected devices overheat, turn them off and turn off their circuit breaker/fuse.

2

BRIGGSandSTRATTON.COM

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Call Transfer Switch Helpline BRIGGSandSTRATTON.COM 100 AMP/200 AMPTransfer Switch Where to Find UsDate Purchased Table of Contents Important Safety Instructions Installer Responsibilities IntroductionFor the Home Owner Owner OrientationInstallation Shipment ContentsUnpacking Mounting GuidelinesAlternate Transfer Switch Mounting Power Wiring Interconnections Utility ConnnectionSystem Setup Supervisory Control WiringControls Testing the Automatic Transfer Switch When Calling the FactoryOperation Automatic SequenceMaintenance SpecificationsUL 1008 Listed Transfer Switch Model Supervisory Contacts RatingTroubleshooting Problem Cause CorrectionSchematic and Wiring Diagram, Models 071018 Schematic and Wiring Diagram, Models 071020 Description Illustrated Parts List, ModelItems Not Illustrated ENCLOSURE, 22 x 16 x 197355GS CLIP, Latching Wire 192597GS DECAL, Utility 240VAC 196094GS192166GS WASHER, Lock 1/4 190984GS DECAL, Fuse193159GS DECAL, Reinstall Barrier 192151GS 197355GS CLIP, Latching WireASSY, Enclosure 196520GS DECAL, UL Listed197355GS CLIP, Latching Wire 195728GS ASSY, Enclosure 196521GS192879GS INSULATION, Circuit Breaker 196094GS 197294GS DECAL, Contacts Rating WASHER, Lock 1/4 192881GSLimited Warranty Reserved Manual de Instalación Del Operario Conectador Automático Dónde puede encontrarnosFecha de compra Mantenimiento MandosEspecificaciones Conserve estas instrucciones Instrucciones importantes de seguridadIntroduccion Para el Propietario DomésticoOrientación para el Propietario Responsabilidades del InstaladorInstalacion DesempaquePautas de Montaje Inspección al Momento de la EntregaFigura 2 Montaje de un Conectador Alternativo Interconexiones de Cableado de Energía Configuración del Sistema Cableado de Control de SupervisiónMandos Sistema FuncionamientoPrueba del conectador automático Secuencia AutomáticaMantenimiento EspecificacionesUL 1008 Listó Conectador Modelo Carga máxima/circuitoReparacion de AveriasGarantía Garantía Limitada Reserved Guide dInstallation Et dUtilisation Commutateur de Transfert Où nous trouverDate d’achat Commandes Fonctionnement Mise à lessai du commutateur de transfert automatiqueEntretien CaractéristiquesInstalación FonctionnementCommandes Veuillez conserver ces instructionsDirectives de sécurité importantes SécuritéResponsabilités de lInstallateur IntroductionAu Propriétaire Résidentiel Conseils au PropriétaireConsignes dinstallation Instalación Commandes Vérification de la LivraisonInstalation DéballageIté Interconnexions du câblage dalimentation ItéEtien RantieConfiguration du système Câblage de contrôleCommandes FonctionnementMise à lessai du commutateur de transfert automatique Séquence AutomatiqueEntretien CaractéristiquesUL 1008 Enuméré Commutateur de Transfert Modéle ModèleDepannage Garantie Limitée
Top Page Image Contents