Briggs & Stratton 71019, 71021 Installation, Unpacking, Mounting Guidelines, Delivery Inspection

Page 6

Installation

Unpacking

Delivery Inspection

After removing the carton, carefully inspect the transfer switch components for any damage that may have occurred during shipment.

IMPORTANT: If loss or damage is noted at time of delivery, have the person(s) making delivery note all damage on the freight bill and affix his signature under the consignor's memo of loss or damage. If loss or damage is noted after delivery, contact the carrier for claim procedures. Missing or damaged parts are not warranted.

Shipment Contents

Automatic Power Transfer Switch

Two Current Transformers

Installation and Operator’s Manual

Mounting Guidelines

The Automatic Transfer Switch is enclosed in NEMA Type 3R enclosures suitable for indoor or indoor/outdoor use.

Guidelines for mounting the Automatic Transfer Switch include:

Install the switch on a firm, sturdy supporting structure.

The switch must be installed with minimum NEMA 3R hardware for conduit connections.

To prevent switch contact distortion, level and plumb the enclosure. This can be done by placing washers between the switch enclosure and the mounting surface.

Never install the switch where any corrosive substance might drip onto the enclosure.

Protect the switch at all times against excessive moisture, dust, dirt, lint, construction grit and corrosive vapors.

A typical installation of the Automatic Power Transfer Switch for Models 071018 and 071019 is depicted in Figure 1. An alternative installation of the Automatic Power Transfer Switch is depicted in Figure 2.

It is best if the transfer switch is mounted near the utility watt-hour meter, either inside or outside. Discuss layout suggestions/changes with the owner before beginning the system installation process.

— — — — — — Control Wiring

Watt -

 

Hourmeter

 

Service

 

Disconnect

Contactor

 

Main

Transfer

Circuit

Breaker

Switch

Panel

Generator

Hot Water

 

Heater

 

Branch Circuits

Air

 

 

Conditioner

 

Disconnect Switch

Figure 1 - Typical Transfer Switch Mounting for Models 071018 and 071019

4

BRIGGSandSTRATTON.COM

Image 6
Contents Call Transfer Switch Helpline BRIGGSandSTRATTON.COM 100 AMP/200 AMPWhere to Find Us Transfer SwitchDate Purchased Table of Contents Important Safety Instructions For the Home Owner Installer ResponsibilitiesIntroduction Owner OrientationUnpacking InstallationShipment Contents Mounting GuidelinesAlternate Transfer Switch Mounting Power Wiring Interconnections Utility ConnnectionSupervisory Control Wiring System SetupControls Operation Testing the Automatic Transfer SwitchWhen Calling the Factory Automatic SequenceUL 1008 Listed Transfer Switch Model MaintenanceSpecifications Supervisory Contacts RatingTroubleshooting Problem Cause CorrectionSchematic and Wiring Diagram, Models 071018 Schematic and Wiring Diagram, Models 071020 Illustrated Parts List, Model DescriptionItems Not Illustrated 192166GS ENCLOSURE, 22 x 16 x 197355GS CLIP, Latching Wire192597GS DECAL, Utility 240VAC 196094GS WASHER, Lock 1/4 190984GS DECAL, FuseASSY, Enclosure 196520GS 193159GS DECAL, Reinstall Barrier 192151GS197355GS CLIP, Latching Wire DECAL, UL Listed192879GS INSULATION, Circuit Breaker 196094GS 197355GS CLIP, Latching Wire 195728GSASSY, Enclosure 196521GS 197294GS DECAL, Contacts Rating WASHER, Lock 1/4 192881GSLimited Warranty Reserved Manual de Instalación Del Operario Dónde puede encontrarnos Conectador AutomáticoFecha de compra Mandos MantenimientoEspecificaciones Conserve estas instrucciones Instrucciones importantes de seguridadOrientación para el Propietario IntroduccionPara el Propietario Doméstico Responsabilidades del InstaladorPautas de Montaje InstalacionDesempaque Inspección al Momento de la EntregaFigura 2 Montaje de un Conectador Alternativo Interconexiones de Cableado de Energía Configuración del Sistema Cableado de Control de SupervisiónPrueba del conectador automático MandosSistema Funcionamiento Secuencia AutomáticaUL 1008 Listó Conectador Modelo MantenimientoEspecificaciones Carga máxima/circuitoReparacion de AveriasGarantía Garantía Limitada Reserved Guide dInstallation Et dUtilisation Où nous trouver Commutateur de TransfertDate d’achat Entretien Commandes FonctionnementMise à lessai du commutateur de transfert automatique CaractéristiquesDirectives de sécurité importantes Instalación FonctionnementCommandesVeuillez conserver ces instructions SécuritéAu Propriétaire Résidentiel Responsabilités de lInstallateurIntroduction Conseils au PropriétaireInstalation Consignes dinstallationInstalación Commandes Vérification de la Livraison DéballageIté Etien Interconnexions du câblage dalimentationIté RantieConfiguration du système Câblage de contrôleMise à lessai du commutateur de transfert automatique CommandesFonctionnement Séquence AutomatiqueUL 1008 Enuméré Commutateur de Transfert Modéle EntretienCaractéristiques ModèleDepannage Garantie Limitée