Logicube Omniclone Xi Getting Started Fast Start, Applying power to the Logicube Omniclone

Page 13

2. Getting Started (Fast Start)

Applying power to the Logicube Omniclone Xi™

The Logicube Omniclone Xi™ is able to detect whether an IDE (parallel) or Serial ATA (SATA) drive is attached to the Master or Target positions. The unit is capable of cloning to/from a SATA drive to an IDE drive and vice versa (as well as IDE to IDE and SATA to SATA).

NOTE: Never attach both an IDE and SATA drive to the same drive position. The unit can only handle one drive on each position.

Before applying power perform the steps listed below.

Connecting Parallel (IDE, EIDE, UDMA) Drives

1.Locate the Master position on the top of your Omniclone-Xi™ unit. You will notice three connections: One for a flat cable (the drive data cable) and another for a small drive power cable. Above is the third connector for the Serial ATA cable.

Note: The drive that is cloned from is always referred to as the Master drive and the drives that are cloned to are always referred to as the Target drives.

2.Attach the 5” UDMA ribbon cable and the drive Power cable to the connectors.

3.Connect the Master hard drive to the cables and verify that the drive’s jumper is set to Single Master.

4.Follow steps 1 – 3 to attach drives to the Target positions of the Logicube Omniclone Xi™.

5.Connect the AC Power Cord to the back of the Logicube Omniclone Xi™ and power-up the

Logicube Omniclone Xi ™ User’s Manual

7

Image 13
Contents Phone 818 700 Fax 818 700 Version Date 2/20/06 Logicube, Inc Chatsworth, CAWarranty Limitation of Liability and Warranty InformationLogicube Disclaimer Table of Contents Omnidiagnostics Loading Software Through the Parallel Port Logicube Omniclone Xi Software UpdatePage Introduction Introduction to the Logicube OmnicloneIntroduction FeaturesSystem description Using this guideIntroduction Logicube Omniclone Introduction Connecting Parallel IDE, EIDE, Udma Drives Applying power to the Logicube OmnicloneGetting Started Fast Start Connecting other types of drives Connecting Serial ATA Sata DrivesUser interface Power and Reset buttonsTouch Screen Calibrating the Touch ScreenButtons Indicator LightsButtons and Interface Installing and Removing the Light BarTime/Date Settings Cloning Modes and SettingsMain Menu Screen About ScreenDrives CloningSelective Partitions Mode Optional Clever Clone ModeClever Clone Step-by-Step Selective Partitions Step-by-Step CleverCopy Mirror Clone Step-by-Step Mirror Clone ModeMaster Manager Step-by-Step Master Manager Mode OptionalDell Optiplex Computers and Master Manager Verify Settings Optional Preference SettingsVerify Speed CHS Translation Modes GeometryGeneral Preferences On Error OptionalIntroduction Set Option On Error Step-by-StepLast Drive Set Option Step-by-StepLast Drive Step-by-Step Setting a Password Step-by-Step Database/Barcode Option PasswordRemoving a Password DatabaseOmniDiagnostics Features OmniDiagnosticsScan Target Mode Repair Target Mode Scan Target Mode Step-by-StepWipeClean Target Mode Repair Target Mode Step-by-StepWipeclean Target Step-by-Step WipeClean SettingsOmnidiagnostics Database/Barcode Option System ContentsCompact Flash CF Files Breakdown of Config.txt Database.csv Database Step-by-Step Database Settings Menu Creating a New Config List, Step-by-Step Barcode Scanner Barcode Scanner SettingsDATABASE/BARCODE Option Minimum requirements Using the USB PortRemoving USB devices How to use under Windows for Master Drive ManagementUsing the USB Port Compact Flash CF Card Connecting Through the Software Setup Menu Connecting the CF Drive to Windows via USBCompact Flash CF Card Drive Cables User Replaceable HardwareProper Handling of Drive Cables Removal and Installation of a Drive StationDrive Stations Removal and Installation of the Power Supply Power SupplyLoading Software Using the Compact Flash Logicube Omniclone Xi Software Updating ProceduresSoftware Loading Instructions Host PC preparation Software Loading InstructionsLogicube Omniclone Xi Software Update FAQ’s Frequently Asked Questions and AnswersFrequently Asked Questions and Answers Frequently Asked Questions and Answers Troubleshooting Guide Frequently Asked Questions and Answers Frequently Asked Questions and Answers Glossary ReferenceCloning, Hard Drive ClusterDefragment ReferenceLarge Geometry, Hard DriveMaster Drive, Logicube Omniclone Parallel Port Master/Single Drive, IDEPartition Sector RAM DiskSlave Drive, IDE Translation Mode, CHS Target Drive, Logicube OmnicloneWiping, Data Fdisk IndexIndex Reference Index