Logicube Omniclone Xi user manual DATABASE/BARCODE Option

Page 45

THE DATABASE/BARCODE OPTION

NOTE: A hands-free stand is available from Wasp Technologies.

Beep Settings – These settings change the volume level of the “beep” that the scanner emits when it successfully reads a barcode.

Enable Bar Code Symbiologies – This setting allows your scanner to read all types of barcodes (i.e. UPC-A,UPC-E,EAN-13, etc.). This setting may be necessary if you are utilizing an unusual barcode type.

NOTE: Advanced barcode settings are available in the User’s Manual that is included with your Barcode Scanner. It is not advised to use these settings as they may interfere with the functionality of the Barcode Scanner on the Omniclone-Xi™.

Logicube Omniclone Xi ™ User’s Manual

39

Image 45

Contents Phone 818 700 Fax 818 700 Version Date 2/20/06 Logicube, Inc Chatsworth, CALimitation of Liability and Warranty Information WarrantyLogicube Disclaimer Table of Contents Omnidiagnostics Loading Software Through the Parallel Port Logicube Omniclone Xi Software UpdatePage Introduction Introduction to the Logicube OmnicloneIntroduction FeaturesSystem description Using this guideIntroduction Logicube Omniclone Introduction Applying power to the Logicube Omniclone Connecting Parallel IDE, EIDE, Udma DrivesGetting Started Fast Start Connecting other types of drives Connecting Serial ATA Sata DrivesUser interface Power and Reset buttonsTouch Screen Calibrating the Touch ScreenButtons Indicator LightsButtons and Interface Installing and Removing the Light BarTime/Date Settings Cloning Modes and SettingsMain Menu Screen About ScreenDrives CloningClever Clone Mode Selective Partitions Mode OptionalClever Clone Step-by-Step Selective Partitions Step-by-Step CleverCopy Mirror Clone Step-by-Step Mirror Clone ModeMaster Manager Step-by-Step Master Manager Mode OptionalDell Optiplex Computers and Master Manager Optional Preference Settings Verify SettingsVerify Speed CHS Translation Modes GeometryOn Error Optional General PreferencesIntroduction Set Option On Error Step-by-StepSet Option Step-by-Step Last DriveLast Drive Step-by-Step Setting a Password Step-by-Step Database/Barcode Option PasswordRemoving a Password DatabaseOmniDiagnostics OmniDiagnostics FeaturesScan Target Mode Repair Target Mode Scan Target Mode Step-by-StepWipeClean Target Mode Repair Target Mode Step-by-StepWipeclean Target Step-by-Step WipeClean SettingsOmnidiagnostics System Contents Database/Barcode OptionCompact Flash CF Files Breakdown of Config.txt Database.csv Database Step-by-Step Database Settings Menu Creating a New Config List, Step-by-Step Barcode Scanner Barcode Scanner SettingsDATABASE/BARCODE Option Minimum requirements Using the USB PortRemoving USB devices How to use under Windows for Master Drive ManagementUsing the USB Port Compact Flash CF Card Connecting Through the Software Setup Menu Connecting the CF Drive to Windows via USBCompact Flash CF Card Drive Cables User Replaceable HardwareRemoval and Installation of a Drive Station Proper Handling of Drive CablesDrive Stations Removal and Installation of the Power Supply Power SupplyLogicube Omniclone Xi Software Updating Procedures Loading Software Using the Compact FlashSoftware Loading Instructions Host PC preparation Software Loading InstructionsLogicube Omniclone Xi Software Update FAQ’s Frequently Asked Questions and AnswersFrequently Asked Questions and Answers Frequently Asked Questions and Answers Troubleshooting Guide Frequently Asked Questions and Answers Frequently Asked Questions and Answers Glossary ReferenceCloning, Hard Drive ClusterDefragment ReferenceGeometry, Hard Drive LargeMaster Drive, Logicube Omniclone Master/Single Drive, IDE Parallel PortPartition RAM Disk SectorSlave Drive, IDE Target Drive, Logicube Omniclone Translation Mode, CHSWiping, Data Fdisk IndexIndex Reference Index