Logicube Omniclone Xi user manual Removal and Installation of the Power Supply

Page 54

USER REPLACEABLE HARDWARE

Power Supply

The OCXi and OCX5i models have an internal power supply that can also be replaced by the user. When it is determined that the power supply needs to be replaced, please follow the procedure below:

Replacement Power Supplies are available from Logicube. Please contact Logicube Sales for more information.

NOTE: The Omniclone OCX2i uses a separate power supply that is not physically connected to the unit.

Removal and Installation of the Power Supply

1.Remove the AC Power Cord from the power supply.

2.Remove the two screws located on either side of the Power Supply.

3.Turn the unit over and remove the six screws that hold the power supply to the bottom of the unit.

4.Lift up on the power supply module to remove it from the unit.

5.Disconnect the cable harness from the main circuit board.

6.Installation of the Power Supply is the opposite of removal.

48	Logicube Omniclone Xi ™ User’s Manual

Image 54

Contents Logicube, Inc Chatsworth, CA Phone 818 700 Fax 818 700 Version Date 2/20/06Limitation of Liability and Warranty Information WarrantyLogicube Disclaimer Table of Contents Omnidiagnostics Logicube Omniclone Xi Software Update Loading Software Through the Parallel PortPage Introduction to the Logicube Omniclone IntroductionFeatures IntroductionUsing this guide System descriptionIntroduction Logicube Omniclone Introduction Applying power to the Logicube Omniclone Connecting Parallel IDE, EIDE, Udma DrivesGetting Started Fast Start Connecting Serial ATA Sata Drives Connecting other types of drivesTouch Screen Power and Reset buttonsUser interface Calibrating the Touch ScreenIndicator Lights ButtonsInstalling and Removing the Light Bar Buttons and InterfaceMain Menu Screen Cloning Modes and SettingsTime/Date Settings About ScreenCloning DrivesClever Clone Mode Selective Partitions Mode OptionalClever Clone Step-by-Step Selective Partitions Step-by-Step CleverCopy Mirror Clone Mode Mirror Clone Step-by-StepMaster Manager Mode Optional Master Manager Step-by-StepDell Optiplex Computers and Master Manager Optional Preference Settings Verify SettingsVerify Speed Geometry CHS Translation ModesOn Error Optional General PreferencesIntroduction On Error Step-by-Step Set OptionSet Option Step-by-Step Last DriveLast Drive Step-by-Step Removing a Password Database/Barcode Option PasswordSetting a Password Step-by-Step DatabaseOmniDiagnostics OmniDiagnostics FeaturesScan Target Mode Scan Target Mode Step-by-Step Repair Target ModeRepair Target Mode Step-by-Step WipeClean Target ModeWipeClean Settings Wipeclean Target Step-by-StepOmnidiagnostics System Contents Database/Barcode OptionCompact Flash CF Files Breakdown of Config.txt Database.csv Database Step-by-Step Database Settings Menu Creating a New Config List, Step-by-Step Barcode Scanner Settings Barcode ScannerDATABASE/BARCODE Option Using the USB Port Minimum requirementsHow to use under Windows for Master Drive Management Removing USB devicesUsing the USB Port Compact Flash CF Card Connecting the CF Drive to Windows via USB Connecting Through the Software Setup MenuCompact Flash CF Card User Replaceable Hardware Drive CablesRemoval and Installation of a Drive Station Proper Handling of Drive CablesDrive Stations Power Supply Removal and Installation of the Power SupplyLogicube Omniclone Xi Software Updating Procedures Loading Software Using the Compact FlashSoftware Loading Instructions Software Loading Instructions Host PC preparationLogicube Omniclone Xi Software Update Frequently Asked Questions and Answers FAQ’sFrequently Asked Questions and Answers Frequently Asked Questions and Answers Troubleshooting Guide Frequently Asked Questions and Answers Frequently Asked Questions and Answers Cloning, Hard Drive ReferenceGlossary ClusterReference DefragmentGeometry, Hard Drive LargeMaster Drive, Logicube Omniclone Master/Single Drive, IDE Parallel PortPartition RAM Disk SectorSlave Drive, IDE Target Drive, Logicube Omniclone Translation Mode, CHSWiping, Data Index FdiskIndex Reference Index