Proxim CPN 63708 manual Rebooting and Resetting, Applying Changes, Resetting Hardware

Page 25

Tsunami MP.11 Installation and Management

REBOOTING AND RESETTING

Some configuration changes require a restart. There are several ways to restart the MP.11, which are described in the following sub-sections.

Applying Changes

Some changes you make become effective only when the MP.11 is rebooted. A reboot stores configuration information in non-volatile memory and then restarts the MP.11 with the new values (see “Soft Reset to Factory Default” on page 26).

In some cases, the MP.11 reminds you that a reboot is required for a change to take effect. You do not must reboot immediately; you can reboot after you have made all your changes.

Rebooting

When you reboot, the changes you have made become effective and the MP.11 is restarted. The changes are saved automatically in non-volatile memory before the actual reboot takes place.

To reboot:

1.Click Commands Î Reboot.

2.Enter the number of seconds to wait before the reboot actually takes place.

3.Click the Reboot button. The MP.11 restarts the embedded software after the entered time has passed. During reboot, you are redirected to a page showing a counting down timer, and you are redirected to the Status page after the timer counts down to 0 (zero). The CLI is disconnected during reboot.

Related CLI command: reboot <number of seconds>

Resetting Hardware

If the MP.11 does not respond for some reason and you are not able to reboot, you can restart by means of a hardware reset. This restarts the MP.11 hardware and embedded software. The last saved configuration is used. The MP.11 automatically saves its configuration every two minutes. Any changes that you have made in the meantime are lost.

To reset the hardware, press and release the RESET button on the MP.11 unit with, for example, a pencil.

Chapter 4. Basic Management	25
CPN 63708	Issue Date: 02/05/2003

Image 25

Contents Tsunami MP.11 Trademarks CopyrightContents Overview Point-to-Point Link Wireless Network TopologiesPoint-to-Multipoint Network Identifying Network Topology and Equipment InstallationFinding a Suitable Location Product Package InstallationInstalling the MP.11 Tsunami MP.11 Installation and Management Attaching a Kensington Security Lock Optional Power Ethernet Link Wireless Link Switching on the MP.11Blinking Green when data sent Blinking Green whenOnline help Installing Documentation and SoftwareDocumentation ScanTool Tftp serverDesktop Mounting Mounting the MP.11Wall Mounting Tsunami MP.11 Installation and Management Ceiling Mounting MP.11 IP Address Management OverviewScanTool Static IP Address Static or Dynamic IP AddressDynamic IP Address with Dhcp WEB Interface Overview Ethernet Port Command Line Interface OverviewSerial Port HyperTerminal Connection Properties Basic Management Rebooting Rebooting and ResettingResetting Hardware Click Commands Î RebootSoft Reset to Factory Default General SettingsClick Commands Î Reset System StatusSystem Configuration Descriptor IP ConfigurationUp Time IP Address Assignment TypeDefault Router IP Address Wireless SlotDefault TTL InterfacesBase Station System Name Interface TypeNetwork Name Frequency ChannelEthernet Port Wireless Monitoring SettingsShow wif show worp show worpcfg Encryption Security SettingsUsing Telnet to Change Passwords PasswordsUsing the Web Interface to Change Passwords Using Snmp to Change PasswordsUpgrading the MP.11 Status Web InterfaceStatus tab shows the System Status and the System Traps System StatusClick Configure Î System ConfigureSystem Systems TrapsNetwork IP ConfigurationDhcp Relay Agent IP Routing Ethernet Wireless Slot aSnmp Telnet IP Access TableTrap Groups Trap Host TableTime out SerialRadius Authentication MAC AuthenticationSecurity Encryption FilteringEthernet Protocol Filtering Ethernet Protocol FilterWired Mask Wired MAC AddressWireless MAC Address Static MAC Pair FilteringSpanning Tree Wireless MaskComment Storm Threshold Wireless ThresholdPer Address Threshold Ethernet ThresholdBroadcast Protocol Filtering MonitorGeneral Worp Radius IcmpPer Station FeaturesLink Test IP ARP Table IP Routes Learn TableDownload CommandsServer IP address File NameUpload RebootHelp ResetUsing Command Help Command Line InterfaceBoot Loader Command Line Interface IntroductionSet Command Show CommandViewing and Changing Parameters Entering StringsWorking with Tables Viewing Table ContentsCreating a Table Row Modifying a Table EntryEnabling, Disabling, or Deleting a Table Row Modifying Several Table EntriesTftp Server Setup ProceduresProcedure Description Image File Download Click Commands Æ DownloadCLI Image File Download CLI Configuration File Upload Configuration BackupClick Commands Æ Upload File Type Config File Operation UploadCLI Configuration File Download Configuration RestoreFile Type Config File Operation Download Hard Reset to Factory Default Soft Reset to Factory DefaultCLI Soft Reset to Factory Defaults Forced Reload Image File Download with the BootloaderCommand prompt is displayed enter the following commands Command Line InterfaceFor example Hardware Specifications SpecificationsChannel Frequencies Radio SpecificationsChannel ID FCC/World Etsi GHz France Japan GHz LED Indicators TroubleshootingMP.11 Does Not Boot MP.11 Connectivity IssuesSerial Link Does Not Work HyperTerminal Connection Properties Ethernet Link does not work Setup and ConfigurationLost the MP.11 Password Setup and ConfigurationMP.11 Responds Slowly Web Interface Does Not WorkTftp Server Does Not Work Command Line Interface Does Not WorkOnline Help Is Not Available Changes Do Not Take Effect ARP GlossaryHttp Icmp WEP