Proxim CPN 63708 Command Line Interface, Command prompt is displayed enter the following commands

Page 70

Tsunami MP.11 Installation and Management

5.Click OK to start the file transfer.

The MP.11 downloads the image file. The TFTP server program should show download activity after a few seconds. When the download is complete, the MP.11 is ready to start the embedded software.

To access the MP.11 see “Chapter 3. Management Overview” on page 17.

Command Line Interface

To use the CLI through the serial port of the MP.11 you need the following items:

▪

▪

A serial RS-232C cable with a male and a female DB-9 connector.

An ASCII terminal program such as HyperTerminal.

Proxim recommends you switch off the MP.11 and the computer before connecting or disconnecting the serial RS-232C cable.

To download an image file:

1.Set up the TFTP server as described in “TFTP Server Setup” on page 64.

2.Start the terminal program (such as HyperTerminal), set the following connection properties, and then connect:

COM port	(for example COM1 or COM2, to which the MP.11 serial port is
	connected)
Bits per second	9600
Data bits	8
Stop bits	1
Flow control	None
Parity	None

3.Press the RESET button on the MP.11 unit; the terminal program displays Power On Self Test (POST) messages.

4.When the Sending Traps to SNMP manager periodically message is displayed after about 30 seconds, press the ENTER key.

5.The command prompt is displayed; enter the following commands:

set ipaddr <IP address MP.11> set ipsubmask <subnet mask> set ipaddrtype static

set tftpipaddr <IP address TFTP server> set tftpfilename <image file name> set ipgw <gateway IP address>

reboot

Chapter 7. Procedures	70
CPN 63708	Issue Date: 02/05/2003

Image 70

Contents Tsunami MP.11 Copyright TrademarksContents Overview Wireless Network Topologies Point-to-Point LinkPoint-to-Multipoint Network Identifying Network Topology and Equipment InstallationFinding a Suitable Location Installation Product PackageInstalling the MP.11 Tsunami MP.11 Installation and Management Attaching a Kensington Security Lock Optional Blinking Green when data sent Switching on the MP.11Power Ethernet Link Wireless Link Blinking Green whenDocumentation ScanTool Installing Documentation and SoftwareOnline help Tftp serverDesktop Mounting Mounting the MP.11Wall Mounting Tsunami MP.11 Installation and Management Ceiling Mounting MP.11 IP Address Management OverviewScanTool Static or Dynamic IP Address Static IP AddressDynamic IP Address with Dhcp WEB Interface Overview Command Line Interface Overview Ethernet PortSerial Port HyperTerminal Connection Properties Basic Management Resetting Hardware Rebooting and ResettingRebooting Click Commands Î RebootClick Commands Î Reset General SettingsSoft Reset to Factory Default System StatusSystem Configuration Up Time IP ConfigurationDescriptor IP Address Assignment TypeDefault TTL Wireless SlotDefault Router IP Address InterfacesNetwork Name Interface TypeBase Station System Name Frequency ChannelEthernet Port Monitoring Settings WirelessShow wif show worp show worpcfg Security Settings EncryptionUsing the Web Interface to Change Passwords PasswordsUsing Telnet to Change Passwords Using Snmp to Change PasswordsUpgrading the MP.11 Status tab shows the System Status and the System Traps Web InterfaceStatus System StatusSystem ConfigureClick Configure Î System Systems TrapsNetwork IP ConfigurationDhcp Relay Agent IP Routing Wireless Slot a EthernetSnmp Trap Groups IP Access TableTelnet Trap Host TableSerial Time outRadius Authentication MAC AuthenticationSecurity Filtering EncryptionEthernet Protocol Filter Ethernet Protocol FilteringWireless MAC Address Wired MAC AddressWired Mask Static MAC Pair FilteringSpanning Tree Wireless MaskComment Per Address Threshold Wireless ThresholdStorm Threshold Ethernet ThresholdBroadcast Protocol Filtering MonitorGeneral Worp Icmp RadiusPer Station FeaturesLink Test IP ARP Table Learn Table IP RoutesServer IP address CommandsDownload File NameReboot UploadReset HelpBoot Loader Command Line Interface Command Line InterfaceUsing Command Help IntroductionViewing and Changing Parameters Show CommandSet Command Entering StringsCreating a Table Row Viewing Table ContentsWorking with Tables Modifying a Table EntryModifying Several Table Entries Enabling, Disabling, or Deleting a Table RowTftp Server Setup ProceduresProcedure Description Image File Download Click Commands Æ DownloadCLI Image File Download Click Commands Æ Upload Configuration BackupCLI Configuration File Upload File Type Config File Operation UploadCLI Configuration File Download Configuration RestoreFile Type Config File Operation Download Hard Reset to Factory Default Soft Reset to Factory DefaultCLI Soft Reset to Factory Defaults Image File Download with the Bootloader Forced ReloadCommand Line Interface Command prompt is displayed enter the following commandsFor example Specifications Hardware SpecificationsChannel Frequencies Radio SpecificationsChannel ID FCC/World Etsi GHz France Japan GHz Troubleshooting LED IndicatorsMP.11 Does Not Boot MP.11 Connectivity IssuesSerial Link Does Not Work HyperTerminal Connection Properties Setup and Configuration Ethernet Link does not workMP.11 Responds Slowly Setup and ConfigurationLost the MP.11 Password Web Interface Does Not WorkTftp Server Does Not Work Command Line Interface Does Not WorkOnline Help Is Not Available Changes Do Not Take Effect Glossary ARPHttp Icmp WEP