Proxim CPN 63708 manual Setup and Configuration, Lost the MP.11 Password, MP.11 Responds Slowly

Page 78

Tsunami MP.11 Installation and Management

SETUP AND CONFIGURATION

The following issues relate to setup and configuration problems.

Lost the MP.11 Password

If you lost your password, you must reset the MP.11 to the default settings. See “Hard Reset to Factory Default” on page 68. The default password is public.

If you record your password, keep it in a safe place.

The MP.11 Responds Slowly

If the MP.11 takes a long time to become available, it could mean that:

▪

▪

▪

No DHCP server is available.

The IP address of the MP.11 is already in use.

Verify that the IP address is assigned only to the MP.11. Do this by switching off the MP.11 and then pinging the IP address. If there is a response to the ping, another device in the network is using the same IP address. If the MP.11 uses a static IP address, switching to DHCP mode could remedy this problem. Also see “Dynamic IP Address with DHCP” on page 19.

There is too much network traffic.

Web Interface Does Not Work

If you cannot connect to the MP.11 through the network:

1.Connect a computer to the serial port of the MP.11 and check the SNMP table. The SNMP table can restrict telnet or HTTP access. For more information, see “Serial Port” on page 22.

2.Open a command prompt window and type:

ping <ip address MP.11> (for example ping 10.0.0.1)

If the MP.11 does not respond, ensure that you have the correct IP address. If the MP.11 responds, the Ethernet connection is working properly, continue with this procedure.

3.Ensure that you are using one of the following Web browsers:

ºMicrosoft Internet Explorer version 5.0 or later

ºNetscape version 6.0 or later

4.Ensure that you are not using a proxy server for the connection with your Web browser (with the CLI command show pelsessions).

5.Ensure that you have not exceeded the maximum number of Web Interface sessions.

Chapter 9. Troubleshooting	78
CPN 63708	Issue Date: 02/05/2003

Image 78

Contents Tsunami MP.11 Copyright TrademarksContents Overview Wireless Network Topologies Point-to-Point LinkPoint-to-Multipoint Network Installation Identifying Network Topology and EquipmentFinding a Suitable Location Installation Product PackageInstalling the MP.11 Tsunami MP.11 Installation and Management Attaching a Kensington Security Lock Optional Blinking Green when data sent Switching on the MP.11Power Ethernet Link Wireless Link Blinking Green whenDocumentation ScanTool Installing Documentation and SoftwareOnline help Tftp serverMounting the MP.11 Desktop MountingWall Mounting Tsunami MP.11 Installation and Management Ceiling Mounting Management Overview MP.11 IP AddressScanTool Static or Dynamic IP Address Static IP AddressDynamic IP Address with Dhcp WEB Interface Overview Command Line Interface Overview Ethernet PortSerial Port HyperTerminal Connection Properties Basic Management Resetting Hardware Rebooting and ResettingRebooting Click Commands Î RebootClick Commands Î Reset General SettingsSoft Reset to Factory Default System StatusSystem Configuration Up Time IP ConfigurationDescriptor IP Address Assignment TypeDefault TTL Wireless SlotDefault Router IP Address InterfacesNetwork Name Interface TypeBase Station System Name Frequency ChannelEthernet Port Monitoring Settings WirelessShow wif show worp show worpcfg Security Settings EncryptionUsing the Web Interface to Change Passwords PasswordsUsing Telnet to Change Passwords Using Snmp to Change PasswordsUpgrading the MP.11 Status tab shows the System Status and the System Traps Web InterfaceStatus System StatusSystem ConfigureClick Configure Î System Systems TrapsIP Configuration NetworkDhcp Relay Agent IP Routing Wireless Slot a EthernetSnmp Trap Groups IP Access TableTelnet Trap Host TableSerial Time outMAC Authentication Radius AuthenticationSecurity Filtering EncryptionEthernet Protocol Filter Ethernet Protocol FilteringWireless MAC Address Wired MAC AddressWired Mask Static MAC Pair FilteringWireless Mask Spanning TreeComment Per Address Threshold Wireless ThresholdStorm Threshold Ethernet ThresholdMonitor Broadcast Protocol FilteringGeneral Worp Icmp RadiusFeatures Per StationLink Test IP ARP Table Learn Table IP RoutesServer IP address CommandsDownload File NameReboot UploadReset HelpBoot Loader Command Line Interface Command Line InterfaceUsing Command Help IntroductionViewing and Changing Parameters Show CommandSet Command Entering StringsCreating a Table Row Viewing Table ContentsWorking with Tables Modifying a Table EntryModifying Several Table Entries Enabling, Disabling, or Deleting a Table RowProcedures Tftp Server SetupProcedure Description Click Commands Æ Download Image File DownloadCLI Image File Download Click Commands Æ Upload Configuration BackupCLI Configuration File Upload File Type Config File Operation UploadConfiguration Restore CLI Configuration File DownloadFile Type Config File Operation Download Soft Reset to Factory Default Hard Reset to Factory DefaultCLI Soft Reset to Factory Defaults Image File Download with the Bootloader Forced ReloadCommand Line Interface Command prompt is displayed enter the following commandsFor example Specifications Hardware SpecificationsRadio Specifications Channel FrequenciesChannel ID FCC/World Etsi GHz France Japan GHz Troubleshooting LED IndicatorsMP.11 Connectivity Issues MP.11 Does Not BootSerial Link Does Not Work HyperTerminal Connection Properties Setup and Configuration Ethernet Link does not workMP.11 Responds Slowly Setup and ConfigurationLost the MP.11 Password Web Interface Does Not WorkCommand Line Interface Does Not Work Tftp Server Does Not WorkOnline Help Is Not Available Changes Do Not Take Effect Glossary ARPHttp Icmp WEP