Proxim CPN 63708 manual Procedures, Tftp Server Setup, Procedure Description

Page 64

Tsunami MP.11 Installation and Management

Chapter 7. Procedures

This chapter contains a set of procedures, as described in the following table:

Procedure	Description

TFTP Server Setup	Prepares the TFTP server for transferring files to and from the
	MP.11. This procedure is used by the other procedures that transfer
	files.

Image File Download	Upgrades the embedded software.

Configuration Backup	Saves the configuration of the MP.11.

Configuration Restore	Restores a previous configuration through configuration file
	download.

Soft Reset to Factory	Resets the MP.11 to the factory default settings through the Web or
Default	Command Line Interface.

Hard Reset to Factory	In some cases, it may be necessary to revert to the factory default
Default	settings (for example, if you cannot access the MP.11 or you lost the
	password for the Web Interface.

Force Reload	Completely resets the MP.11 and erases the embedded software.
	Use this procedure only as a last resort if the MP.11 does not boot
	and the “Hard Reset to Factory Default” procedure did not help. If
	you perform a “Forced Reload,” you must download a new image file
	as described in “Image File Download with the Boot Loader.”

Image File Download	If the MP.11 does not contain embedded software, or the embedded
with the Boot Loader	software is corrupt, you can use this procedure to download a new
	image file.

TFTP SERVER SETUP

To download or upload a file, you must connect to the computer with the TFTP server through the MP.11’s Ethernet port. This can be any computer in the network or a computer connected to the MP.11 with a cross-over Ethernet cable. For information about installing the TFTP server, see “Installing Documentation and Software” on page 13.

Ensure that the upload or download directory is correctly set, the required file is present in the directory, and the TFTP server is running. The TFTP server must be running only during file upload and download. You can check the connectivity between the MP.11 and the TFTP server by pinging the MP.11 from the computer that hosts the TFTP server. The ping program should show replies from the MP.11.

Chapter 7. Procedures	64
CPN 63708	Issue Date: 02/05/2003

Image 64

Contents Tsunami MP.11 Copyright TrademarksContents Overview Wireless Network Topologies Point-to-Point LinkPoint-to-Multipoint Network Identifying Network Topology and Equipment InstallationFinding a Suitable Location Installation Product PackageInstalling the MP.11 Tsunami MP.11 Installation and Management Attaching a Kensington Security Lock Optional Switching on the MP.11 Power Ethernet Link Wireless LinkBlinking Green when data sent Blinking Green whenInstalling Documentation and Software Online helpDocumentation ScanTool Tftp serverDesktop Mounting Mounting the MP.11Wall Mounting Tsunami MP.11 Installation and Management Ceiling Mounting MP.11 IP Address Management OverviewScanTool Static or Dynamic IP Address Static IP AddressDynamic IP Address with Dhcp WEB Interface Overview Command Line Interface Overview Ethernet PortSerial Port HyperTerminal Connection Properties Basic Management Rebooting and Resetting RebootingResetting Hardware Click Commands Î RebootGeneral Settings Soft Reset to Factory DefaultClick Commands Î Reset System StatusSystem Configuration IP Configuration DescriptorUp Time IP Address Assignment TypeWireless Slot Default Router IP AddressDefault TTL InterfacesInterface Type Base Station System NameNetwork Name Frequency ChannelEthernet Port Monitoring Settings WirelessShow wif show worp show worpcfg Security Settings EncryptionPasswords Using Telnet to Change PasswordsUsing the Web Interface to Change Passwords Using Snmp to Change PasswordsUpgrading the MP.11 Web Interface StatusStatus tab shows the System Status and the System Traps System StatusConfigure Click Configure Î SystemSystem Systems TrapsNetwork IP ConfigurationDhcp Relay Agent IP Routing Wireless Slot a EthernetSnmp IP Access Table TelnetTrap Groups Trap Host TableSerial Time outRadius Authentication MAC AuthenticationSecurity Filtering EncryptionEthernet Protocol Filter Ethernet Protocol FilteringWired MAC Address Wired MaskWireless MAC Address Static MAC Pair FilteringSpanning Tree Wireless MaskComment Wireless Threshold Storm ThresholdPer Address Threshold Ethernet ThresholdBroadcast Protocol Filtering MonitorGeneral Worp Icmp RadiusPer Station FeaturesLink Test IP ARP Table Learn Table IP RoutesCommands DownloadServer IP address File NameReboot UploadReset HelpCommand Line Interface Using Command HelpBoot Loader Command Line Interface IntroductionShow Command Set CommandViewing and Changing Parameters Entering StringsViewing Table Contents Working with TablesCreating a Table Row Modifying a Table EntryModifying Several Table Entries Enabling, Disabling, or Deleting a Table RowTftp Server Setup ProceduresProcedure Description Image File Download Click Commands Æ DownloadCLI Image File Download Configuration Backup CLI Configuration File UploadClick Commands Æ Upload File Type Config File Operation UploadCLI Configuration File Download Configuration RestoreFile Type Config File Operation Download Hard Reset to Factory Default Soft Reset to Factory DefaultCLI Soft Reset to Factory Defaults Image File Download with the Bootloader Forced ReloadCommand Line Interface Command prompt is displayed enter the following commandsFor example Specifications Hardware SpecificationsChannel Frequencies Radio SpecificationsChannel ID FCC/World Etsi GHz France Japan GHz Troubleshooting LED IndicatorsMP.11 Does Not Boot MP.11 Connectivity IssuesSerial Link Does Not Work HyperTerminal Connection Properties Setup and Configuration Ethernet Link does not workSetup and Configuration Lost the MP.11 PasswordMP.11 Responds Slowly Web Interface Does Not WorkTftp Server Does Not Work Command Line Interface Does Not WorkOnline Help Is Not Available Changes Do Not Take Effect Glossary ARPHttp Icmp WEP