Proxim CPN 63708 Switching on the MP.11, Power Ethernet Link Wireless Link, Blinking Green when

Page 12

Tsunami MP.11 Installation and Management

The Kensington Security Slot is shown in the following figures (the figure on the left shows the slot with the cable cover attached; the figure on the right shows the slot with the cable cover removed).

For information about Kensington security solutions, go to http://www.kensington.com .

SWITCHING ON THE MP.11

The MP.11 can be powered by a power supply or by Active Ethernet through an Active Ethernet splitter. Depending upon the powering method, you can switch the MP.11 on by:

▪

▪

Plugging the power cord of the power supply into an AC power outlet

Connecting the Active Ethernet splitter to the Ethernet cabling

When the power is switched on, the MP.11 performs start-up diagnostics. When the start-up is completed, the LEDs show the operational state of the MP.11. The following table shows the status of the LEDs when the MP.11 is operational. In the event the POWER LED is red, something is wrong; check your setup.

	Power	Ethernet Link	Wireless Link

	OFF when no power is	OFF when not connected.	OFF wireless interface is up
	present or	Green when connected at	properly, but no wireless link
	malfunctioning	Green when connected at	established.
	malfunctioning	10 Mbps.	established.
		10 Mbps.
	Green when power is	Blinking Green when	Green immediately after
	present and the unit is	Blinking Green when	connecting a link.
	present and the unit is	data sent.	connecting a link.
	operational.	data sent.
	operational.		Blinking Green when data sent.
		Amber when connected at	Blinking Green when data sent.
	Amber when the unit	Amber when connected at
	Amber when the unit	100 Mbps.	Amber when in Forced Reload
	has a failure (try Reload	100 Mbps.	Amber when in Forced Reload
	has a failure (try Reload		state.
	to fix the problem).	Blinking Amber when	state.
	to fix the problem).	Blinking Amber when
	Red when there is a	data sent.	Red when the wireless interface
	Red when there is a		is down.
	fatal error in the unit.	Red when there is an error	is down.
	fatal error in the unit.	Red when there is an error
		in data transfer.	Blinking Red when there is a
			data packet error (loss).

Chapter 2. Installation	12
CPN 63708	Issue Date: 02/05/2003

Image 12

Contents Tsunami MP.11 Copyright TrademarksContents Overview Wireless Network Topologies Point-to-Point LinkPoint-to-Multipoint Network Installation Identifying Network Topology and EquipmentFinding a Suitable Location Installation Product PackageInstalling the MP.11 Tsunami MP.11 Installation and Management Attaching a Kensington Security Lock Optional Switching on the MP.11 Power Ethernet Link Wireless LinkBlinking Green when data sent Blinking Green whenInstalling Documentation and Software Online helpDocumentation ScanTool Tftp serverMounting the MP.11 Desktop MountingWall Mounting Tsunami MP.11 Installation and Management Ceiling Mounting Management Overview MP.11 IP AddressScanTool Static or Dynamic IP Address Static IP AddressDynamic IP Address with Dhcp WEB Interface Overview Command Line Interface Overview Ethernet PortSerial Port HyperTerminal Connection Properties Basic Management Rebooting and Resetting RebootingResetting Hardware Click Commands Î RebootGeneral Settings Soft Reset to Factory DefaultClick Commands Î Reset System StatusSystem Configuration IP Configuration DescriptorUp Time IP Address Assignment TypeWireless Slot Default Router IP AddressDefault TTL InterfacesInterface Type Base Station System NameNetwork Name Frequency ChannelEthernet Port Monitoring Settings WirelessShow wif show worp show worpcfg Security Settings EncryptionPasswords Using Telnet to Change PasswordsUsing the Web Interface to Change Passwords Using Snmp to Change PasswordsUpgrading the MP.11 Web Interface StatusStatus tab shows the System Status and the System Traps System StatusConfigure Click Configure Î SystemSystem Systems TrapsIP Configuration NetworkDhcp Relay Agent IP Routing Wireless Slot a EthernetSnmp IP Access Table TelnetTrap Groups Trap Host TableSerial Time outMAC Authentication Radius AuthenticationSecurity Filtering EncryptionEthernet Protocol Filter Ethernet Protocol FilteringWired MAC Address Wired MaskWireless MAC Address Static MAC Pair FilteringWireless Mask Spanning TreeComment Wireless Threshold Storm ThresholdPer Address Threshold Ethernet ThresholdMonitor Broadcast Protocol FilteringGeneral Worp Icmp RadiusFeatures Per StationLink Test IP ARP Table Learn Table IP RoutesCommands DownloadServer IP address File NameReboot UploadReset HelpCommand Line Interface Using Command HelpBoot Loader Command Line Interface IntroductionShow Command Set CommandViewing and Changing Parameters Entering StringsViewing Table Contents Working with TablesCreating a Table Row Modifying a Table EntryModifying Several Table Entries Enabling, Disabling, or Deleting a Table RowProcedures Tftp Server SetupProcedure Description Click Commands Æ Download Image File DownloadCLI Image File Download Configuration Backup CLI Configuration File UploadClick Commands Æ Upload File Type Config File Operation UploadConfiguration Restore CLI Configuration File DownloadFile Type Config File Operation Download Soft Reset to Factory Default Hard Reset to Factory DefaultCLI Soft Reset to Factory Defaults Image File Download with the Bootloader Forced ReloadCommand Line Interface Command prompt is displayed enter the following commandsFor example Specifications Hardware SpecificationsRadio Specifications Channel FrequenciesChannel ID FCC/World Etsi GHz France Japan GHz Troubleshooting LED IndicatorsMP.11 Connectivity Issues MP.11 Does Not BootSerial Link Does Not Work HyperTerminal Connection Properties Setup and Configuration Ethernet Link does not workSetup and Configuration Lost the MP.11 PasswordMP.11 Responds Slowly Web Interface Does Not WorkCommand Line Interface Does Not Work Tftp Server Does Not WorkOnline Help Is Not Available Changes Do Not Take Effect Glossary ARPHttp Icmp WEP