Proxim CPN 63708 manual Attaching a Kensington Security Lock Optional

Page 11

Tsunami MP.11 Installation and Management

6.Connect one end of an Ethernet cable to the Ethernet port. The other end of the cable should not be connected to another device until after installation is complete.

ºUse a straight-through Ethernet cable if you intend to connect the router to a hub, switch, patch panel, or Active Ethernet power injector.

ºUse a cross-over Ethernet cable if you intend to connect the router to a single computer.

7.If you are not using Active Ethernet, or you want to connect the router to Active Ethernet and AC power simultaneously, attach the AC power cable to the router’s power port.

Once attached, the power cable locks into place. To disconnect the power cable, slide back the black plastic fitting and gently pull the cable from the connector.

8.Connect the free end of the Ethernet cable to a hub, switch, patch panel, Active Ethernet power injector, or an Ethernet port on a computer.

9.If using AC power, connect the power cord to a power source (such as a wall outlet) to turn on the unit.

10.Place the unit in the final installation location (see “Mounting the MP.11” on page 14 for details).

11.Replace the back cover, front cover, and cable cover. Be careful to avoid trapping the power and Ethernet cables when replacing the cable cover.

Attaching a Kensington Security Lock (Optional)

If so desired, you can attach a Kensington lock to secure the cable cover into place. This protects the unit from unauthorized tampering.

The MP.11 enclosure includes a Kensington Security Slot for use with a Kensington locking mechanism. When properly installed, a Kensington lock can prevent unauthorized personnel from stealing the MP.11. In addition, the Kensington lock secures the cable cover in place, which prevents tampering with the Ethernet and power cables.

Chapter 2. Installation	11
CPN 63708	Issue Date: 02/05/2003

Image 11

Contents Tsunami MP.11 Trademarks CopyrightContents Overview Point-to-Point Link Wireless Network TopologiesPoint-to-Multipoint Network Finding a Suitable Location InstallationIdentifying Network Topology and Equipment Product Package InstallationInstalling the MP.11 Tsunami MP.11 Installation and Management Attaching a Kensington Security Lock Optional Blinking Green when Switching on the MP.11Power Ethernet Link Wireless Link Blinking Green when data sentTftp server Installing Documentation and SoftwareOnline help Documentation ScanToolWall Mounting Mounting the MP.11Desktop Mounting Tsunami MP.11 Installation and Management Ceiling Mounting ScanTool Management OverviewMP.11 IP Address Static IP Address Static or Dynamic IP AddressDynamic IP Address with Dhcp WEB Interface Overview Ethernet Port Command Line Interface OverviewSerial Port HyperTerminal Connection Properties Basic Management Click Commands Î Reboot Rebooting and ResettingRebooting Resetting HardwareSystem Status General SettingsSoft Reset to Factory Default Click Commands Î ResetSystem Configuration IP Address Assignment Type IP ConfigurationDescriptor Up TimeInterfaces Wireless SlotDefault Router IP Address Default TTLFrequency Channel Interface TypeBase Station System Name Network NameEthernet Port Wireless Monitoring SettingsShow wif show worp show worpcfg Encryption Security SettingsUsing Snmp to Change Passwords PasswordsUsing Telnet to Change Passwords Using the Web Interface to Change PasswordsUpgrading the MP.11 System Status Web InterfaceStatus Status tab shows the System Status and the System TrapsSystems Traps ConfigureClick Configure Î System SystemDhcp Relay Agent IP ConfigurationNetwork IP Routing Ethernet Wireless Slot aSnmp Trap Host Table IP Access TableTelnet Trap GroupsTime out SerialSecurity MAC AuthenticationRadius Authentication Encryption FilteringEthernet Protocol Filtering Ethernet Protocol FilterStatic MAC Pair Filtering Wired MAC AddressWired Mask Wireless MAC AddressComment Wireless MaskSpanning Tree Ethernet Threshold Wireless ThresholdStorm Threshold Per Address ThresholdGeneral MonitorBroadcast Protocol Filtering Worp Radius IcmpLink Test FeaturesPer Station IP ARP Table IP Routes Learn TableFile Name CommandsDownload Server IP addressUpload RebootHelp ResetIntroduction Command Line InterfaceUsing Command Help Boot Loader Command Line InterfaceEntering Strings Show CommandSet Command Viewing and Changing ParametersModifying a Table Entry Viewing Table ContentsWorking with Tables Creating a Table RowEnabling, Disabling, or Deleting a Table Row Modifying Several Table EntriesProcedure Description ProceduresTftp Server Setup CLI Image File Download Click Commands Æ DownloadImage File Download File Type Config File Operation Upload Configuration BackupCLI Configuration File Upload Click Commands Æ UploadFile Type Config File Operation Download Configuration RestoreCLI Configuration File Download CLI Soft Reset to Factory Defaults Soft Reset to Factory DefaultHard Reset to Factory Default Forced Reload Image File Download with the BootloaderCommand prompt is displayed enter the following commands Command Line InterfaceFor example Hardware Specifications SpecificationsChannel ID FCC/World Etsi GHz France Japan GHz Radio SpecificationsChannel Frequencies LED Indicators TroubleshootingSerial Link Does Not Work MP.11 Connectivity IssuesMP.11 Does Not Boot HyperTerminal Connection Properties Ethernet Link does not work Setup and ConfigurationWeb Interface Does Not Work Setup and ConfigurationLost the MP.11 Password MP.11 Responds SlowlyOnline Help Is Not Available Command Line Interface Does Not WorkTftp Server Does Not Work Changes Do Not Take Effect ARP GlossaryHttp Icmp WEP