Proxim CPN 63708 manual MP.11 Connectivity Issues, MP.11 Does Not Boot, Serial Link Does Not Work

Page 75

Tsunami MP.11 Installation and Management

Power

Ethernet Link

Wireless Link

 

 

 

OFF when no power is

OFF when not connected.

OFF wireless interface is up

present or

Green when connected at

properly, but no wireless link

malfunctioning

established.

10 Mbps.

 

 

Green when power is

Blinking Green when

Green immediately after

present and the unit is

connecting a link.

data sent.

operational.

 

 

Blinking Green when data sent.

 

Amber when connected at

Amber when the unit

 

100 Mbps.

Amber when in Forced Reload

has a failure (try Reload

 

state.

to fix the problem).

Blinking Amber when

 

Red when there is a

data sent.

Red when the wireless interface

 

is down.

fatal error in the unit.

Red when there is an error

 

 

in data transfer.

Blinking Red when there is a

 

 

data packet error (loss).

 

 

 

MP.11 CONNECTIVITY ISSUES

The issues described in this section relate to the connections of the MP.11.

MP.11 Does Not Boot

The MP.11 shows no activity (the power LED is off).

1.Ensure that the power supply is properly working and correctly connected.

2.Ensure that all cables are correctly connected.

3.Check the power source.

4.If you are using an Active Ethernet splitter, ensure that the voltage is correct.

Serial Link Does Not Work

The MP.11 cannot be reached through the serial port.

1.Check the cable connection between the MP.11 and the computer.

2.Ensure that the correct COM port is used.

3.Start the terminal program; set the following connection properties (also see “HyperTerminal Connection Properties”), and then connect.

COM port

For example, COM1 or COM2, to which the MP.11 serial port is connected

Bits per second

9600

Data bits

0

Stop bits

1

Flow control

None

Parity

None

Line ends

Carriage return with line feed

4.Ensure that the MP.11 and the computer use the same serial port configuration parameters.

Chapter 9. Troubleshooting

75

CPN 63708

Issue Date: 02/05/2003

Page 74 Page 76
Image 75
Page 74 Page 76
Contents Tsunami MP.11 Trademarks CopyrightContents Overview Point-to-Point Link Wireless Network TopologiesPoint-to-Multipoint Network Installation Identifying Network Topology and EquipmentFinding a Suitable Location Product Package InstallationInstalling the MP.11 Tsunami MP.11 Installation and Management Attaching a Kensington Security Lock Optional Blinking Green when Switching on the MP.11Power Ethernet Link Wireless Link Blinking Green when data sentTftp server Installing Documentation and SoftwareOnline help Documentation ScanToolMounting the MP.11 Desktop MountingWall Mounting Tsunami MP.11 Installation and Management Ceiling Mounting Management Overview MP.11 IP AddressScanTool Static IP Address Static or Dynamic IP AddressDynamic IP Address with Dhcp WEB Interface Overview Ethernet Port Command Line Interface OverviewSerial Port HyperTerminal Connection Properties Basic Management Click Commands Î Reboot Rebooting and ResettingRebooting Resetting HardwareSystem Status General SettingsSoft Reset to Factory Default Click Commands Î ResetSystem Configuration IP Address Assignment Type IP ConfigurationDescriptor Up TimeInterfaces Wireless SlotDefault Router IP Address Default TTLFrequency Channel Interface TypeBase Station System Name Network NameEthernet Port Wireless Monitoring SettingsShow wif show worp show worpcfg Encryption Security SettingsUsing Snmp to Change Passwords PasswordsUsing Telnet to Change Passwords Using the Web Interface to Change PasswordsUpgrading the MP.11 System Status Web InterfaceStatus Status tab shows the System Status and the System TrapsSystems Traps ConfigureClick Configure Î System SystemIP Configuration NetworkDhcp Relay Agent IP Routing Ethernet Wireless Slot aSnmp Trap Host Table IP Access TableTelnet Trap GroupsTime out SerialMAC Authentication Radius AuthenticationSecurity Encryption FilteringEthernet Protocol Filtering Ethernet Protocol FilterStatic MAC Pair Filtering Wired MAC AddressWired Mask Wireless MAC AddressWireless Mask Spanning TreeComment Ethernet Threshold Wireless ThresholdStorm Threshold Per Address ThresholdMonitor Broadcast Protocol FilteringGeneral Worp Radius IcmpFeatures Per StationLink Test IP ARP Table IP Routes Learn TableFile Name CommandsDownload Server IP addressUpload RebootHelp ResetIntroduction Command Line InterfaceUsing Command Help Boot Loader Command Line InterfaceEntering Strings Show CommandSet Command Viewing and Changing ParametersModifying a Table Entry Viewing Table ContentsWorking with Tables Creating a Table RowEnabling, Disabling, or Deleting a Table Row Modifying Several Table EntriesProcedures Tftp Server SetupProcedure Description Click Commands Æ Download Image File DownloadCLI Image File Download File Type Config File Operation Upload Configuration BackupCLI Configuration File Upload Click Commands Æ UploadConfiguration Restore CLI Configuration File DownloadFile Type Config File Operation Download Soft Reset to Factory Default Hard Reset to Factory DefaultCLI Soft Reset to Factory Defaults Forced Reload Image File Download with the BootloaderCommand prompt is displayed enter the following commands Command Line InterfaceFor example Hardware Specifications SpecificationsRadio Specifications Channel FrequenciesChannel ID FCC/World Etsi GHz France Japan GHz LED Indicators TroubleshootingMP.11 Connectivity Issues MP.11 Does Not BootSerial Link Does Not Work HyperTerminal Connection Properties Ethernet Link does not work Setup and ConfigurationWeb Interface Does Not Work Setup and ConfigurationLost the MP.11 Password MP.11 Responds SlowlyCommand Line Interface Does Not Work Tftp Server Does Not WorkOnline Help Is Not Available Changes Do Not Take Effect ARP GlossaryHttp Icmp WEP
Top Page Image Contents