Nortel Networks NN44200-313 quick start Checking the current IP address of the PBX LD

Page 14

14CS 1000/M1 system status check

•"Checking the status of the ELAN connection to the PBX (LD 48)" (page 15)

Checking the current IP address of the PBX (LD 117)

Perform the following procedure to check the current IP address in the CS 1000 or M1 system.

Step Action

1Connect to the PBX.

2If you have not already done so, log on using the proper account with the following syntax:

logi <login name>

3Press Enter.

4At the prompt, type the password for the login name and press Enter.

5Enter LD 117.

6Enter STAT HOST to display the IP addresses and host names conﬁgured in the CS 1000 or M1 system.

Note: If there is no IP provisioning completed, see the CS 1000 System and CallPilot Server Conﬁguration guide (NN44200-312) for advanced provisioning. When provisioning is complete, return to this guide and continue to the next procedure.

7To exit the overlay, enter ****.

—End—

Checking the currently conﬁgured VAS IDs

Step Action

1Connect to the PBX.

2Enter LD 22.

3At the REQ prompt, enter PRT.

4At the TYPE prompt, enter VAS.

5If there are some VAS IDs provisioned, take note of the VAS ID information. If there are no VAS IDs provisioned, this guide explains the steps to provision them in the next chapter.

Nortel CallPilot

Quickstart Guide

NN44200-313 01.02 Standard

5.019 May 2008

Copyright © 2007-2008, Nortel Networks

Image 14

Contents Quickstart Guide Page Page Page Contents CallPilot server preinstallation Getting help from the Nortel Web site How to get helpGetting help over the phone from a Nortel Solutions Center Getting help through a Nortel distributor or reseller CallPilot 5.0 installation Prerequisites to CallPilot 5.0 installationCallPilot 5.0 installation tasks CS 1000/M1 system status check tasksTime requirements Time requirements Task Time to completionCallPilot 5.0 installation CS 1000/M1 system status check CS 1000/M1 system status check tasksChecking the current IP address of the PBX LD Checking the currently conﬁgured VAS IDsChecking the status of the Elan connection to the PBX LD Checking the Elan interface status of the PBX LDEnabling the Elan interface of the PBX LD 16 CS 1000/M1 system status check CallPilot resource conﬁguration CallPilot resource conﬁguration tasksLD 17 Conﬁguring the VAS ID Prompt Response Conﬁguring a new Elan ID and VAS ID LDLD 17 Conﬁguring the Elan ID Prompt Response Secu YES Conﬁguring system parameters LDPrompt Response LD 17 Conﬁguring system parameters Prompt ResponseDeﬁning CallPilot in the customer data block LD LD 15 Conﬁguring End-to-End Signaling Tone Prompt Response LD 15 Conﬁguring Call Redirection Prompt ResponsePNI Conﬁguring the Route Data Block LDIsdn YES HlocRoute Conﬁguring Automatic Call Distribution LDLD 16 Conﬁguring the Route Data Block Prompt Response Idef LOC Rcls EXTAcdn Conﬁguring the Dfdn LDREQ NEW Type ACD Cust MWC MaxpNcfw Conﬁguring the CDN queue LDLD 23 Conﬁguring Dfdn Prompt Response LD 23 Conﬁguring the CDN queue PromptDfdn Conﬁguring ACD agents LDType CDN Cust LD 11 Conﬁguring ACD agents Prompt ResponseKEY Provisioning telephones LDCLS KEY MSB NRD TRNFDN LD 11 Provisioning telephones Prompt ResponseZone CLS FNA MWA HTA HuntEnabling card slots LD Saving CS 1000/M1 changes LD 600r CallPilot server front panel CallPilot server general description600r CallPilot server Back panel 600r CallPilot server front panel LEDs Label Description1005r CallPilot server USB ID LEDDVD/CD/CD-RW Label Description Label Description USB 0 dongle connects here CallPilot server preinstallation Recommended toolsPreparing the site CallPilot server preinstallation tasksChoosing a location Connecting to the network Unpacking the serverEnd Rack-mounting the server CallPilot server installationCallPilot server installation tasks Installing peripheral devices Installing cables and grounds Continue with Performing preboot checks Performing preboot checks Connecting the server to power and starting itStep Action CallPilot server conﬁguration tasks Completing the Setup Wizard and installing PEPsCallPilot server conﬁguration Logging on to the CallPilot serverCallPilot server conﬁguration Mailbox number Password Running the Conﬁguration WizardType the Computer name From the Application Name list, select Voice Messaging Conﬁguring new mailboxes and additional tasks From the Template Name list, select Regular User TemplateBacking up the system End Checking CallPilot connectivity and channels CallPilot server testingCallPilot server testing tasks Verifying that you can log on to mailboxes Verifying that you can leave a message Verifying that you can retrieve a messageTesting pcAnywhere using a remote PC What is next? Following is a complete list of CallPilot 5.0 NTPsCallPilot server testing Appendix Installing the CallPilot 5.0 image Installing the CallPilot 5.0 imageReturn to CallPilot server conﬁguration Conﬁguring a phantom superloop Appendix Conﬁguring phantom DNsChecking for existing phantom loops Cden Creating a phantom DNLD 10 Creating a phantom DN Prompt Response CLS WTA UNR FTR Quickstart Guide