Nortel Networks NN44200-313 quick start Installing cables and grounds

Page 43

Installing cables and grounds 43

6Set the SCSI ID on the tape drive to 6.

7Install the monitor, keyboard, and mouse in the same location as the server.

If you are using a KVM-type box, ensure that you have visual contact with the LEDs on the CallPilot server.

8Plug the keyboard and mouse cables into the PS/2 connectors on the rear panel according to the labels.

9Plug the monitor into the video connector on the rear panel. Tighten screws on the connector.

10Install the USB dongle into USB port 0. Ensure that the feature key is in place.

—End—

Installing cables and grounds

Perform the following procedure to install cables and grounds for the

CallPilot server.

This procedure assumes that the cable and RJ45 are terminated properly according to IEEE 802 Ethernet standards and are of sufﬁcient length. This procedure does not cover Ethernet cables of customized length.

Step Action

1Install and connect the ELAN Ethernet cable to the NIC 2 connector labeled on the back of the server from the ELAN hub or Ethernet switch.

Or, use an Ethernet cross-over cable to connect directly to the CS 1000 or M1 switch. If you use this method, no device other than CallPilot can connect to the ELAN subnet.

Note: Connect the CS 1000 or M1 switch ELAN to the same subnet as the CallPilot server ELAN.

2Install and connect the Ethernet cable for the Nortel server subnet to the NIC 1 connector labeled on the back of the server from the Nortel server subnet hub or Ethernet switch.

Not all sites require a Nortel server subnet; this subnet is used for the following features: Desktop Messaging, CallPilot Reporter, My CallPilot, CallPilot Manager remote access, and Application Builder.

Note: Leave the Ethernet cable for the Nortel server subnet unplugged on the server side until antivirus software is installed on the server.

Nortel CallPilot

Quickstart Guide

NN44200-313 01.02 Standard

5.019 May 2008

Copyright © 2007-2008, Nortel Networks

Image 43

Contents Quickstart Guide Page Page Page Contents CallPilot server preinstallation Getting help over the phone from a Nortel Solutions Center How to get helpGetting help from the Nortel Web site Getting help through a Nortel distributor or reseller Prerequisites to CallPilot 5.0 installation CallPilot 5.0 installationCS 1000/M1 system status check tasks CallPilot 5.0 installation tasksTime requirements Task Time to completion Time requirementsCallPilot 5.0 installation CS 1000/M1 system status check tasks CS 1000/M1 system status checkChecking the currently conﬁgured VAS IDs Checking the current IP address of the PBX LDEnabling the Elan interface of the PBX LD Checking the Elan interface status of the PBX LDChecking the status of the Elan connection to the PBX LD 16 CS 1000/M1 system status check CallPilot resource conﬁguration tasks CallPilot resource conﬁgurationLD 17 Conﬁguring the Elan ID Prompt Response Conﬁguring a new Elan ID and VAS ID LDLD 17 Conﬁguring the VAS ID Prompt Response LD 17 Conﬁguring system parameters Prompt Response Conﬁguring system parameters LDPrompt Response Secu YESDeﬁning CallPilot in the customer data block LD LD 15 Conﬁguring Call Redirection Prompt Response LD 15 Conﬁguring End-to-End Signaling Tone Prompt ResponseHloc Conﬁguring the Route Data Block LDIsdn YES PNIIdef LOC Rcls EXT Conﬁguring Automatic Call Distribution LDLD 16 Conﬁguring the Route Data Block Prompt Response RouteMWC Maxp Conﬁguring the Dfdn LDREQ NEW Type ACD Cust AcdnLD 23 Conﬁguring the CDN queue Prompt Conﬁguring the CDN queue LDLD 23 Conﬁguring Dfdn Prompt Response NcfwLD 11 Conﬁguring ACD agents Prompt Response Conﬁguring ACD agents LDType CDN Cust DfdnKEY MSB NRD TRN Provisioning telephones LDCLS KEYCLS FNA MWA HTA Hunt LD 11 Provisioning telephones Prompt ResponseZone FDNEnabling card slots LD Saving CS 1000/M1 changes LD 600r CallPilot server CallPilot server general description600r CallPilot server front panel 600r CallPilot server front panel LEDs Label Description Back panel1005r CallPilot server DVD/CD/CD-RW ID LEDUSB Label Description Label Description USB 0 dongle connects here Recommended tools CallPilot server preinstallationChoosing a location CallPilot server preinstallation tasksPreparing the site Unpacking the server Connecting to the networkEnd CallPilot server installation tasks CallPilot server installationRack-mounting the server Installing peripheral devices Installing cables and grounds Continue with Performing preboot checks Connecting the server to power and starting it Performing preboot checksStep Action Logging on to the CallPilot server Completing the Setup Wizard and installing PEPsCallPilot server conﬁguration CallPilot server conﬁguration tasksCallPilot server conﬁguration Running the Conﬁguration Wizard Mailbox number PasswordType the Computer name From the Application Name list, select Voice Messaging From the Template Name list, select Regular User Template Conﬁguring new mailboxes and additional tasksBacking up the system End CallPilot server testing tasks CallPilot server testingChecking CallPilot connectivity and channels Verifying that you can log on to mailboxes Verifying that you can retrieve a message Verifying that you can leave a messageTesting pcAnywhere using a remote PC Following is a complete list of CallPilot 5.0 NTPs What is next?CallPilot server testing Installing the CallPilot 5.0 image Appendix Installing the CallPilot 5.0 imageReturn to CallPilot server conﬁguration Checking for existing phantom loops Appendix Conﬁguring phantom DNsConﬁguring a phantom superloop LD 10 Creating a phantom DN Prompt Response Creating a phantom DNCden CLS WTA UNR FTR Quickstart Guide