Nortel Networks NN44200-313 quick start CallPilot server conﬁguration tasks

Page 47

47

CallPilot server conﬁguration

This task describes the CallPilot server conﬁguration.

CallPilot server conﬁguration tasks

The following is a list of tasks you perform to conﬁgure the CallPilot server. To link to detailed procedures for each task, click the text.

•"Logging on to the CallPilot server" (page 47)

•"Completing the Setup Wizard and installing PEPs" (page 47)

•"Running the Conﬁguration Wizard" (page 49)

•"Conﬁguring new mailboxes and additional tasks" (page 52)

•"Backing up the system" (page 53)

Logging on to the CallPilot server

Perform the following procedure to log on to the CallPilot server.

Step Action

1From the local console, for the user name, enter administrator.

2From the local console, for the password, enter Bvw250.

—End—

Completing the Setup Wizard and installing PEPs

Perform the following procedure to install Service Updates (SU) and PEPs on the CallPilot server.

Step Action

1After you log on, the Setup Wizard appears automatically. Click Next on the Welcome page of the Setup Wizard.

2Insert the PEP CD into the DVD-ROM drive.

Nortel CallPilot

Quickstart Guide

NN44200-313 01.02 Standard

5.019 May 2008

Copyright © 2007-2008, Nortel Networks

Image 47

Contents Quickstart Guide Page Page Page Contents CallPilot server preinstallation Getting help from the Nortel Web site How to get helpGetting help over the phone from a Nortel Solutions Center Getting help through a Nortel distributor or reseller Prerequisites to CallPilot 5.0 installation CallPilot 5.0 installationCS 1000/M1 system status check tasks CallPilot 5.0 installation tasksTime requirements Task Time to completion Time requirementsCallPilot 5.0 installation CS 1000/M1 system status check tasks CS 1000/M1 system status checkChecking the currently conﬁgured VAS IDs Checking the current IP address of the PBX LDChecking the status of the Elan connection to the PBX LD Checking the Elan interface status of the PBX LDEnabling the Elan interface of the PBX LD 16 CS 1000/M1 system status check CallPilot resource conﬁguration tasks CallPilot resource conﬁgurationLD 17 Conﬁguring the VAS ID Prompt Response Conﬁguring a new Elan ID and VAS ID LDLD 17 Conﬁguring the Elan ID Prompt Response LD 17 Conﬁguring system parameters Prompt Response Conﬁguring system parameters LDPrompt Response Secu YESDeﬁning CallPilot in the customer data block LD LD 15 Conﬁguring Call Redirection Prompt Response LD 15 Conﬁguring End-to-End Signaling Tone Prompt ResponseHloc Conﬁguring the Route Data Block LDIsdn YES PNIIdef LOC Rcls EXT Conﬁguring Automatic Call Distribution LDLD 16 Conﬁguring the Route Data Block Prompt Response RouteMWC Maxp Conﬁguring the Dfdn LDREQ NEW Type ACD Cust AcdnLD 23 Conﬁguring the CDN queue Prompt Conﬁguring the CDN queue LDLD 23 Conﬁguring Dfdn Prompt Response NcfwLD 11 Conﬁguring ACD agents Prompt Response Conﬁguring ACD agents LDType CDN Cust DfdnKEY MSB NRD TRN Provisioning telephones LDCLS KEYCLS FNA MWA HTA Hunt LD 11 Provisioning telephones Prompt ResponseZone FDNEnabling card slots LD Saving CS 1000/M1 changes LD 600r CallPilot server front panel CallPilot server general description600r CallPilot server 600r CallPilot server front panel LEDs Label Description Back panel1005r CallPilot server USB ID LEDDVD/CD/CD-RW Label Description Label Description USB 0 dongle connects here Recommended tools CallPilot server preinstallationPreparing the site CallPilot server preinstallation tasksChoosing a location Unpacking the server Connecting to the networkEnd Rack-mounting the server CallPilot server installationCallPilot server installation tasks Installing peripheral devices Installing cables and grounds Continue with Performing preboot checks Connecting the server to power and starting it Performing preboot checksStep Action Logging on to the CallPilot server Completing the Setup Wizard and installing PEPsCallPilot server conﬁguration CallPilot server conﬁguration tasksCallPilot server conﬁguration Running the Conﬁguration Wizard Mailbox number PasswordType the Computer name From the Application Name list, select Voice Messaging From the Template Name list, select Regular User Template Conﬁguring new mailboxes and additional tasksBacking up the system End Checking CallPilot connectivity and channels CallPilot server testingCallPilot server testing tasks Verifying that you can log on to mailboxes Verifying that you can retrieve a message Verifying that you can leave a messageTesting pcAnywhere using a remote PC Following is a complete list of CallPilot 5.0 NTPs What is next?CallPilot server testing Installing the CallPilot 5.0 image Appendix Installing the CallPilot 5.0 imageReturn to CallPilot server conﬁguration Conﬁguring a phantom superloop Appendix Conﬁguring phantom DNsChecking for existing phantom loops Cden Creating a phantom DNLD 10 Creating a phantom DN Prompt Response CLS WTA UNR FTR Quickstart Guide