Panasonic KX-FC195AL manual Battery charge, Battery icon Battery strength, Battery life

Page 22

2. Preparation

2.2 Battery charge

Place the handset on the cradle of the base unit for about 7 hours before initial use.

1

2

Note:

LClean the handset charge contacts (1) and the base unit charge contacts (2) with a dry cloth once a month, or the batteries may not charge properly.

Battery strength

LDuring charging, the battery icon on the handset display is shown as follows.

When the batteries are fully charged, 0677794 flashes.

The handset is automatically turned on when placed on the base unit.

In normal use, the handset and the base unit should be powered on at all times.

LWhile the handset is off the base unit, the battery icon is shown as follows.

Battery icon	Battery strength
67779	High

68779	Medium

68879	Low

0688794	Needs to be recharged

Battery life

–When using fully charged nickel metal hydride (Ni-MH) batteries (700 mAh): Talk time: Approx. 10 hours Standby time: Approx. 120 hours

–When using fully charged nickel cadmium (Ni-Cd) batteries (250 mAh):

Talk time: Approx. 4 hours

Standby time: Approx. 40 hours

LTimes indicated are for peak performance. L The batteries cannot be overcharged.

L For maximum battery life, it is recommended that the handset is not recharged until 0688794 flashes or the handset beeps intermittently while it is in use.

L Battery life is dependent on usage conditions and ambient temperature.

Important:

LTo prevent battery consumption, be sure to press {ih} if a busy tone sounds when/after using the handset.

e.g., After receiving fax documents using the handset.

20

Image 22

Contents Operating Instructions How to use the operating instructions OpenHandset Location of controlsBase unit KeysFor your future reference CopyrightPage Important information InstallationService difficulties Instructions to customerFor best performance Battery chargeOperating distance and noise Important safety instructions InstallationBattery Introduction Installation PhonebookIndex Included accessories Quantity SpecificationsAvailable accessories Accessory informationModel No Specifications/Usage Description of base unit buttons OverviewReceiver Microphone Description of handset buttons Description of handset displayInk film Before installationInstalling the ink film Raising the antennaReplacing the ink film IncorrectPaper tray Metal recording paper guideBattery replacement Battery installationRecording paper Power on Turning the handset power on/offPower off Connections Battery icon Battery strength Battery chargeBattery strength Battery lifeRinger volume Adjusting handset volumeBase unit help function Speaker volume Adjusting base unit volumeHandset receiver volume Fax voice guidance volumeDate and time Setting the time and date on the handsetSetting the date and time on the base unit Example 1515 24 hour clock entry PressYour logo To delete a character To select characters using a or BTo change capital or lower-case letters Keys CharactersExample +64 9 Your fax numberTo delete a number Making phone calls With the handsetAnswering phone calls With the base unitDigital SP-PHONEand talk into the microphone Handset locatorStoring names and telephone numbers into the phonebook Press LOCATOR/HOLDEditing a stored entry Making a phone call using the phonebookHot key Erasing a stored entryHelpful hints Making a phone call using a hot keyErasing a hot key To delete a character/numberCaller ID service Handset only Making a phone call using the navigator directoryHow Caller ID is displayed Visual Call Waiting Call Waiting ID Service Calling back will not be possible in the following casesStoring caller information into the phonebook Handset only This feature is not available in the following casesErasing caller information Sending a fax manually Sending a fax using the navigator directory Documents you can sendAdding a new entry into the broadcast memory Broadcast transmissionProgramming entries into the broadcast memory Erasing a stored entry from the broadcast memoryHow to receive calls with the base unit Activating TEL modeTo cancel broadcast transmission Receiving a fax manuallyActivating TAD/FAX mode Activating FAX only modeReceiving a fax automatically Ring setting in TAD/FAX mode Receiving a voice message and fax document in one callUsing with the ring detection feature More copying features Making a copyTo collate multiple copies Example Making 2 copies of a 4-page original documentErasing your recorded greeting message Recording your greeting messageLeaving a message for others or yourself StopListening to recorded messages Erasing recorded messagesWhen voice memory is full Voice guide Remote operations using the remote command keyKey Remote command Operating from a remote locationAllowing callers to leave private messages Other remote operationsTo use a mailbox Recording your mailbox greeting messagesListening to recorded mailbox messages Leaving messages in a mailboxTransferring recorded messages to another telephone How this feature worksRecording your transfer greeting message Pager call To check the transfer greeting messageTo erase your transfer greeting message Example 202 555 1234PP12345678PP5555#Programming advanced features Basic featuresProgramming basic features Base unit programmingAdvanced features Code #42 Setting the message alert Code #31 Activating the Distinctive Ring featureCode #34 Setting the quick scan Code #43 Setting the recording time alertCode #47 Setting the fax voice guidance Code #44 Setting the memory reception alertCode #46 Setting friendly reception Code #51 Setting the mailbox 1 passwordHandset programming Ringer option settings Setting the time of alarmChanging the time alarm frequency Ringer volume SeeSelecting the talk mode display Display option settings Selecting the standby mode displaySelecting the display language Setting the direct call number Call option settings Setting the call BARChanging the direct call setting Resetting the handset settings to their default settings Setting the auto talkSetting the battery type Feature Default settingCancelling a call restricted number Handset programming using the base unit PINSetting call restriction Changing base unit PINHandset can be reset to the following default settings Registering a handset to a base unit Cancelling a handsetOperating additional units Example Additional handsets registered to 2 base unitsSetting all handsets to ring Selecting the ringer modeCancelling a base unit Setting the selected handsets to ringIntercom between handsets Transferring calls between handsets/Conference callCommunication Error Code 40-42, 46-72, FF Error messages ReportsError messages Base unit display Communication Error Code 43Cannot make and receive calls When a function does not work, check hereGeneral Unit does not workCordless handset Fax sending Fax receivingCopying Recording paper jam If a power failure occursWhen the recording paper has jammed in the unit Answering deviceCorrect When the recording paper was not fed into the unit properly Document jams sendingThermal head cleaning Document feeder cleaningDo not use paper products, such as paper towels or tissues Help Fax number list Setup listReference lists and reports Printer testTechnical data about this product RF Transmission Power Paper specificationsDuplex procedure StandardApprox g Index TAD/FAX Index Page Page 62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan