Kathrein UFD 580S manual Initial Setup, Getting Started, Power Failure Safety, Error Signalling

Page 16

Initial Setup

Getting Started

Connect the unit to the mains power supply.

Switch on the receiver by pressing the power button on the front of the unit.

The LED shows “- - - - ”.

The operation indicator LED lights up red, the unit is in standby.

Switch on the receiver by pressing the button on the remote control.

The red LED on the front panel of the receiver flashes each time a button on the remote control is pressed.

The screen displays the factory preset programme. In the bottom section of the screen is an information bar showing the name of the programme provider, the time, the timer settings, the programme status and title, provided those details are being broadcast. The LED display indicates the programme's memory location number.

The red standby indicator goes out.

You can now receive the factory preset TV and radio programmes and call them up by pressing the buttons. Press (blue) and to select

radio programmes. Press the blue button again to return to the TV programmes.

For details of how to save additional TV and radio programmes, refer to the "TV/Radio Programme Lists" section.

Please check the time is correct according to whether you are on Summer or Winter time.

When you switch on, the last reception status set is always restored.

Power Failure Safety

After a power failure, the receiver automatically powers up, obtains the time from the reception signal and then returns to standby. This preserves the timer settings.

Error Signalling

If the message “Weak signal or no signal” appears on the screen as well as the display for the last programme received, check the installation of the system and/or the receiver settings. If this only affects individual programme slots, there may be an interrupted signal from the programme provider or a fault in the reception system (cable or satellite system).

First of all, check the connection configuration and whether the default receiver settings are correct for your system. In case of doubt, consult a specialist engineer.

16

Image 16
Contents Twin-DVR Sat Receiver UFD 580/580S With Hard Disk Drive Preface Important InformationContents Factory Default Entering the Password Parental Control UFOmicro Safety Instructions Important Information Receiver-Features Remote control RCRemote Control Menu Functions    Controls, Displays und Connections View of front panel flap folded down View of rear panelYou must run through steps 4-6 for each satellite received Menu Concept Operating InstructionsAlphanumeric Inputs Language Selection OSD Alphanumeric Assignment of Remote Control Number ButtonsButton Connection and Setup Connecting the UnitReception System Presets Sat if ConnectionOperation on one Antenna Connection ReceptionInserting Batteries in the Remote Control TV and Video Recorder ConnectionAudio Connection Spdif Connections Electrical/OpticalInitial Setup Power Failure SafetyError Signalling Getting StartedReceiver Presetting Important On-Screen Displays On Screen Display OSDHelp Function TV Channel Identifier Error SignallingRadio Channel Identifier TV/Radio Channel List Videotext Teletext Selecting a TV Programme Channel ListReception Status Selecting a TV Programme by Number Switching to a Radio Programme Follow the instructions given by your Pay TV provider Common InterfaceYou alone are responsible for use of the cards Common Interface Twin Functions Picture-in-Picture PIPTime-Shift One-Touch RecordingTvtv EPG and Timer Accessing the Tvtv EPG for the First TimeAccessing the Tvtv EPG Current ViewProgramme List Highlights Programmes Sorted by CategorySearch Function Details Programming a Recording Press  to save the selected recording data Timer List Overlaps of series timer recordings are displayed in orange Tvtv EPG and Timer Key to Symbols Explanation Channel List SF2LNB Configuration Overview Hard Disk RecorderRecording and Watching TV Tuner inputRecording Hard Disk CapacityTime-Shift Recording One-Touch Recording OTR Timer Recording Stopping a RecordingSpecial Functions Split Take Playback and RecordingFast Forward/Fast Rewind no picture Playback = Setting Index Marks Skip Points Index marks at the end of a recordingAudio Mode DeleteSearch Time-Shifted PlaybackAudio Settings Setting the VolumeStereo and Two-Channel Sound Playback MutingProgramme List FavouritesGenerating a Favourites List Alphabetical Channel Search Programme List Sorting Programmes Deleting Programmes Manually Adding ProgrammesProgramme List Selecting the Last Programmes Received Password Factory Default Entering the PasswordPassword Parental Control Password Using the Front Panel Backup OperationSetting System Parameters System Parameters Local Time/TimerSystem Information TV Type Aspect RatioScreen ModeSatellite Setup Adding/Removing SatellitesEntering a Satellite Name Removing SatellitesLNB Configuration Installation MenuOscillator Frequency L.O Operation Changing the Oscillator FrequencyReceiving Two Satellites DiSEqC Setting Tuner SelectAntenna Setup Antenna Rotor/Positioner DiSEqC1.2Satellite Scan TP Edit/Scan Transponder Selection Important Note on Deleting Transponders ASTRA, 12,603.75 MHz, symbol rate 22MSymb/s, horizontalAll new programmes are added to the existing programme list KHz Signal DiSEqC UFO SetupTone Burst and DiSEqC Signal Tone Burst DiSEqCDiSEqC Repeat UFO miniProcedure see Reset does not delete the pre-programmingFactory Set Logging on to UFOmicro Video Recorder Connection PlaybackSoftware and Programme List Update Software and Programme List Update Receiver to Receiver Data Transfer PreparationsProgramme List Download Operating System Software DownloadTechnical Features Technical AppendixTechnical Data Connections Temperature rangeGeneral VHS/S-VHS Switching AccessoriesScart Socket Assignment Connection Example Troubleshooting Problem Cause RemedyDiSEqC components Short Technical GuideEB/NO ratio Symbol rate Programme packageTransponder Video bit rateGlossary Service SatelliteService Service Service 936.2576/B/0605/ZWT Technical data subject to change