Kathrein UFD 580S manual Antenna Setup, Antenna Rotor/Positioner DiSEqC1.2

Page 75

Installation Menu

Antenna Setup

This menu is exclusively intended for service purposes and be used to align the antenna in an emergency, if no measuring instruments are available.

The first line is used to specify the satellite and the second line to specify the transponder.

The polarisation of the received signal and the transmitted symbol rate are shown on the next line.

The bars provide information about the strength (relative level) of the signal and its quality. However, this information cannot be used to draw any conclusions about the quality of the antenna system or the cable connection.

Antenna Rotor/Positioner (DiSEqC™1.2)

For operation with a rotor (DiSEqC™1.2), select “On” on the “Motor/Goto 0°” line.

On the next line, “Move/Save”, you can align the antenna to the east

or to the west using the or button. Press to confirm. The optimum setup can be viewed in the "Level" bar chart.

On the “Set Limit” line, you can press or to specify the outermost aiming point (limited by a wall or other obstruction) in a westerly or easterly direction.

Always read the operating manual supplied by the rotor manufacturer thoroughly (particularly with regard to settings different to those described above).

75

Image 75
Contents Twin-DVR Sat Receiver UFD 580/580S With Hard Disk Drive Important Information PrefaceContents Factory Default Entering the Password Parental Control UFOmicro Safety Instructions Important Information Remote control RC Receiver-Features    Remote Control Menu FunctionsView of front panel flap folded down View of rear panel Controls, Displays und ConnectionsYou must run through steps 4-6 for each satellite received Operating Instructions Menu ConceptAlphanumeric Inputs Alphanumeric Assignment of Remote Control Number Buttons Language Selection OSDButton Sat if Connection Connection and SetupConnecting the Unit Reception System PresetsReception Operation on one Antenna ConnectionSpdif Connections Electrical/Optical Inserting Batteries in the Remote ControlTV and Video Recorder Connection Audio ConnectionGetting Started Initial SetupPower Failure Safety Error SignallingReceiver Presetting On Screen Display OSD Important On-Screen DisplaysHelp Function Error Signalling TV Channel IdentifierRadio Channel Identifier TV/Radio Channel List Videotext Teletext Channel List Selecting a TV ProgrammeReception Status Selecting a TV Programme by Number Switching to a Radio Programme Common Interface Follow the instructions given by your Pay TV providerYou alone are responsible for use of the cards Common Interface Picture-in-Picture PIP Twin FunctionsOne-Touch Recording Time-ShiftAccessing the Tvtv EPG for the First Time Tvtv EPG and TimerCurrent View Accessing the Tvtv EPGProgramme List Programmes Sorted by Category HighlightsSearch Function Details Programming a Recording Press  to save the selected recording data Timer List Overlaps of series timer recordings are displayed in orange Tvtv EPG and Timer Key to Symbols Explanation SF2 Channel ListTuner input LNB Configuration OverviewHard Disk Recorder Recording and Watching TVHard Disk Capacity RecordingTime-Shift Recording One-Touch Recording OTR Stopping a Recording Timer RecordingSpecial Functions Playback and Recording Split TakePlayback Fast Forward/Fast Rewind no picture = Index marks at the end of a recording Setting Index Marks Skip PointsTime-Shifted Playback Audio ModeDelete SearchMuting Audio SettingsSetting the Volume Stereo and Two-Channel Sound PlaybackFavourites Programme ListGenerating a Favourites List Alphabetical Channel Search Programme List Sorting Programmes Manually Adding Programmes Deleting ProgrammesProgramme List Selecting the Last Programmes Received Factory Default Entering the Password PasswordPassword Parental Control Password Backup Operation Using the Front PanelSetting System Parameters Local Time/Timer System ParametersSystem Information Mode TV TypeAspect Ratio ScreenAdding/Removing Satellites Satellite SetupRemoving Satellites Entering a Satellite NameInstallation Menu LNB ConfigurationOscillator Frequency L.O Changing the Oscillator Frequency OperationReceiving Two Satellites Tuner Select DiSEqC SettingAntenna Rotor/Positioner DiSEqC1.2 Antenna SetupSatellite Scan TP Edit/Scan Transponder Selection ASTRA, 12,603.75 MHz, symbol rate 22MSymb/s, horizontal Important Note on Deleting TranspondersAll new programmes are added to the existing programme list DiSEqC UFO Setup KHz SignalTone Burst and DiSEqC Signal UFO mini Tone BurstDiSEqC DiSEqC RepeatReset does not delete the pre-programming Procedure seeFactory Set Logging on to UFOmicro Playback Video Recorder ConnectionSoftware and Programme List Update Software and Programme List Update Operating System Software Download Receiver to Receiver Data TransferPreparations Programme List DownloadTechnical Appendix Technical FeaturesTechnical Data Temperature range ConnectionsGeneral Accessories VHS/S-VHS SwitchingScart Socket Assignment Connection Example Problem Cause Remedy TroubleshootingShort Technical Guide DiSEqC componentsEB/NO ratio Video bit rate Symbol rateProgramme package TransponderGlossary Satellite ServiceService Service Service 936.2576/B/0605/ZWT Technical data subject to change