VistaQuest N7227V5 installation instructions Relay Unit if installed in cabinet

Page 12

4204 Relay Unit (if installed in cabinet)

1.Insert self-tapping screws (provided) in two adjacent raised cabinet tabs. Leave the heads projecting 1/8".

2.Hang the unit on the screw heads via two of the slotted holes at the rear of its housing, as shown in Figure 2.

3.The 4204's cover can be left off if the unit's DIP switch is set with its position 1 "ON" (to the right) as shown in its instructions. The tampered cover is necessary for installations outside of the control's cabinet.

CIRCUIT

BOARD

CABINET

DETAIL B
SIDE VIEW OF		DETAIL A
LONG MOUNTING CLIPS	CONTROL	SIDE VIEW OF
	CONTROL	BOARD SUPPORTING SLOTS
	CIRCUIT	BOARD SUPPORTING SLOTS
	CIRCUIT
	BOARD

Figure 2. Installing The PC Board in the Cabinet Alone, or (if used), With a 4204 Relay Unit

Figure 3. Installing The PC Board And RF Receiver Together In The Cabinet

– 12 –

Image 12

Contents VISTA-10SE Recommendations For Smoke And Heat Detectors Recommendations For Proper Intrusion ProtectionTable of Contents Relay Output Devices Sequential Mode For 5800 Series Wireless Transmitters SectionList of Figures HOW to USE this Manual Conventions Used in this Manual Wireless Expansion General DescriptionAC Power Supply Back-Up BatteryOptional Phone module Supports the Ademco 4285 Phone module Communication FormatsInstalling the Control Installing the Lock if usedMounting the Cabinet Relay Unit if installed in cabinet Standard Phone Line Connections Standard Telephone Line ConnectionsWiring The AC Transformer Installing The Back-Up BatteryWiring Table Do not Connect the Wires to the Battery YETInstalling Remote Keypads Wiring To The KeypadsKeypads That May Be Used Mounting the Keypads Keypad Connections To The Control BoardPreliminary Check-out Procedure Using a Supplementary Power Supply For KeypadsBasic HARD-WIRED Zones Installing the Hard-Wired ZonesWiring Burglary and Panic Devices To Zones Wiring 4-Wire Smoke/Combustion Detectors on ZoneProgramming Hard-Wired Zones Zone Types Check-Out Procedure For Hard-Wired Zones Special Notes on ZoneProgramming Wireless RF Zone Expansion 5800 RF Systems Wireless Systems AvailableSeries Receiver Wireless Zones Wireless System Operation and Transmitter SupervisionTransmitter Battery Life Wireless System Installation AdvisoriesInstallation and Setup of the 4281/5881 Wireless Receivers Receiver SupervisionSeries Transmitter Setup BoardSetting the DIP Switches On 5700 SeriesRefer to the Compatible 5700 Series TransmittersDIP Switch Tables for 5700 RF System Wireless Devices Compatible 5700 Series Transmitters Model Product Zone/ID # DescriptionProgramming the Control For a 5700 Wireless System Using the House ID Sniffer Mode 5700 SystemsEnter your Installer Code + # + Zone Programming For 5700 TransmittersProgramming Guide Enter the Installer Code + # + Programming 5700 RFSystems Series Transmitter Setup Compatible 5800 Series Transmitters TempProgramming the RF Transmitters 5800 RF Systems GBDRF House ID Code Enrolling 5800 Transmitters Into The SystemEnrolling Through Zone Programming ZN ZT RC In L 0 0 0 0 RF Recommend that you confirm the programming of every Transmitter before proceeding to the next zoneCheck-Out Procedure for Wireless Zones Sniffer ModeTransmitter ID Go/No Go Test Relay Output Devices Relay Device BasicsRelay Modules Alarm Programming Output Relays Choices for Zone Types Example of Output Relay Programming Installing the Phone module Phone Module WiringPhone Module General InformationTerminal Connects to Caller ID UnitsWiring Notes 4285Programming The Control For Phone Access Press 95. Ring Detection CountVoice Answering Module Downloading Field 95 ProgrammingChecking the Operation of the 4285 Phone module To Check Phone module Operation From an On-Premises PhoneTo Check Phone module Operation From an Off-Premises Phone External Sounders Press 30. Alarm Bell Timeout Testing the SounderSounder Connections Press 51. Confirmation of Arming DingLong Range Radio General InformationConnection Audio Alarm Verification AAV Wiring ConnectionsProgramming Connection Of AAV Unit When Not Using a 4285 Phone module Final Power UP To bypass this delay, press # +Calculating the Battery Size Needed ExampleMaking the Battery ConnectionsDevice Current # Units Total Current Total =Entering Zone Descriptors program menu mode SectionProgramming the Descriptors PressO R Press 6 to accept the selected word Press 8 to save all words in memoryAlternate Method For Programming Zone Descriptors Method Alpha Vocabulary List For Adding Custom WordsSequential Mode For 5800 Series Wireless Transmitters Serial # ↑ Page System Communication Following describes each format in greater detailAdemco Contact ID Reporting takes the following format +1/4+1 Report Standard ExpandedCommunication Programming Table of Contact ID Event CodesPress 45 Phone System Select Enter 1 digit default = Press 46 Report FORMAT, PRIMARY/SECONDARYPress 47 SPLIT/DUAL Reporting To Primary Phone No To Secondary Phone NoTo Program System Status and Restore Report Codes 60 68, 70 Press 60 Trouble Report CodePress 61 Bypass Report Code Press 62 AC Loss Report CodePress65 OPEN/EXIT Alarm Report CODE, 1st Digits Press 67 RF XMTR. LOW Battery Report CodePress 68 Cancel Report Code Press 70 Alarm Restore Report CODE, 1st DigitPress 74 LOW BAT Restore Report Code Press 75 RF XMTR. LOW Battery Restore CodePress 92 Number of Reports in Armed Period Press 94 Download Phone NumberTesting the System Test ProcedureTo the Installer System Operation To program a Duress codeTo change the Duress code To delete the Duress codeFeatures for Each Arming Mode Keypad FunctionsDisarmed, Not Ready Forced Quick BypassKeys Displayed as Zone If usedRelay Outputs Security Code + # +Trouble Conditions See Troubleshooting Guide also Troubleshooting Guide System including WirelessControl Please Before you call Technical Support, be sure youRead the Instructions Specifications & Accessories SpecificationsVISTA-10SE Security Control Remote Keypad Remote KeypadsTransmitter Module Relay Module Phone ModuleZones With the Ademco VISTA-10SE Accessories Compatible Devices No CNAdemco 702 Outdoor SirenFederal Communications Commission FCC Part 15 Statement Federal Communications Commission FCC Part 68 StatementUL Notices Canadian Department of Communications DOC Statement Limitations of this Alarm System ADT VISTA-10SE Summary of Connections Ademco Limited Warranty