VistaQuest N7227V5 Programming 5700 RF, Systems, Enter the Installer Code + # +

Page 30

10.Mark the zone number on the transmitter.

11.After the transmitter has been entered into the system, press [✱] to continue.

Typical summary display

Zn ZT – RC In: L

20 03 – 3C RF: –

Pr ogr a m Alpha ?

0 = No 1 = Ye s 0

Ente r Zn Num .

 

(0 0 = Q uit)

2 1

A summary of the programmed values for the selected zone will now be displayed

If all is okay, press [ ✱] for the next display.

Alpha descriptors for the zones can be done now, or may be done at a later time using ✱82 interactive mode (enter “0”).

Refer to ALPHA DESCRIPTOR PROGRAMMING section for performing this procedure in the ✱82 interactive menu mode.

If “0” (no) was entered in response to the Pr ogr a m Alpha ? question, a prompt will then be displayed for entry of the number for the next wireless zone to be programmed.

12.Proceed with the programming of the next wireless zone, starting at step 5 again.

13.To exit field ✱ 56 when completed, key [0 ][0] at the “Enter Zone Number” prompt.

14.Exit the programming mode by keying ✱99.

Special Notes on Zone

•

In field *56, at the summary line for each zone, the entered values can be

Programming (5700 RF

 

checked. If you wish to change anything, press [#] to move to the previous

Systems)

 

entry. Press [#] a number of times to move to earlier entries. Press [✱] to

 

 

move to later entries again.

 

•

Zone entries can be reviewed by pressing [#][5][6]. Changes cannot be

 

 

made here, so this is safer for review. Enter the first zone number to be

 

 

viewed and press [#]. To view each zone, press [#] and the zone number

 

 

will advance to the next programmed zone. When the end of the list is

 

 

reached, press [0][0] to exit. This method of exiting may also be done at any

 

 

time during the review.

 

•

To either temporarily or permanently remove a zone from the system, go

 

 

into programming mode and press [ ✱][5][6]. Enter the zone number and

 

 

press [ ✱]. At the Zone Type prompt, enter [0][0] and [ ✱]. This sets the type

 

 

of the zone to Not Used. The next prompt will be "Delete Zone?". "Yes" will

 

 

permanently remove the zone from the system, while "No" will disable it but

 

 

retain all data except the original zone type. You can then go back to this

 

 

zone later and put back an active Zone Type to re-enable it.

Go/No Go Test Before mounting transmitters permanently, conduct Go/No Go tests to verify adequate signal strength and reorient or relocate transmitters if necessary.

During this mode, wireless receiver gain is reduced by 50%. Testing in this mode assists in determining good mounting locations for the transmitters and verifies that the RF transmission has sufficient signal amplitude margin for the installed system.

1.Enter the Installer Code + # + 4

2.Once transmitters are placed in their desired locations and the approximate length of wire to be run to sensors is connected to the transmitter's screw terminals, fault each transmitter. Do not conduct this test with your hand wrapped around the transmitter as this will cause inaccurate results.

• The keypad will beep three times to indicate signal reception.

– 30 –

Page 29 Page 31
Image 30
Page 29 Page 31
Contents VISTA-10SE Recommendations For Smoke And Heat Detectors Recommendations For Proper Intrusion ProtectionTable of Contents Relay Output Devices Sequential Mode For 5800 Series Wireless Transmitters SectionList of Figures HOW to USE this Manual Conventions Used in this Manual Wireless Expansion General DescriptionOptional Phone module Supports the Ademco 4285 Phone module AC Power SupplyBack-Up Battery Communication FormatsInstalling the Control Installing the Lock if usedMounting the Cabinet Relay Unit if installed in cabinet Standard Phone Line Connections Standard Telephone Line ConnectionsWiring Table Wiring The AC TransformerInstalling The Back-Up Battery Do not Connect the Wires to the Battery YETInstalling Remote Keypads Wiring To The KeypadsKeypads That May Be Used Mounting the Keypads Keypad Connections To The Control BoardPreliminary Check-out Procedure Using a Supplementary Power Supply For KeypadsWiring Burglary and Panic Devices To Zones Basic HARD-WIRED ZonesInstalling the Hard-Wired Zones Wiring 4-Wire Smoke/Combustion Detectors on ZoneProgramming Hard-Wired Zones Zone Types Check-Out Procedure For Hard-Wired Zones Special Notes on ZoneProgramming Series Receiver Wireless Zones Wireless RF Zone Expansion 5800 RF SystemsWireless Systems Available Wireless System Operation and Transmitter SupervisionInstallation and Setup of the 4281/5881 Wireless Receivers Transmitter Battery LifeWireless System Installation Advisories Receiver SupervisionSeries Transmitter Setup BoardRefer to the Compatible 5700 Series Setting the DIP SwitchesOn 5700 Series TransmittersDIP Switch Tables for 5700 RF System Wireless Devices Compatible 5700 Series Transmitters Model Product Zone/ID # DescriptionEnter your Installer Code + # + Programming the Control For a 5700 Wireless SystemUsing the House ID Sniffer Mode 5700 Systems Zone Programming For 5700 TransmittersProgramming Guide Enter the Installer Code + # + Programming 5700 RFSystems Series Transmitter Setup Compatible 5800 Series Transmitters TempProgramming the RF Transmitters 5800 RF Systems GBDRF House ID Code Enrolling 5800 Transmitters Into The SystemEnrolling Through Zone Programming ZN ZT RC In L 0 0 0 0 RF Recommend that you confirm the programming of every Transmitter before proceeding to the next zoneCheck-Out Procedure for Wireless Zones Sniffer ModeTransmitter ID Go/No Go Test Relay Output Devices Relay Device BasicsRelay Modules Alarm Programming Output Relays Choices for Zone Types Example of Output Relay Programming Phone Module Installing the Phone modulePhone Module Wiring General InformationTerminal Connects to Caller ID UnitsWiring Notes 4285Voice Answering Module Programming The Control For Phone AccessPress 95. Ring Detection Count Downloading Field 95 ProgrammingChecking the Operation of the 4285 Phone module To Check Phone module Operation From an On-Premises PhoneTo Check Phone module Operation From an Off-Premises Phone External Sounders Sounder Connections Press 30. Alarm Bell TimeoutTesting the Sounder Press 51. Confirmation of Arming DingLong Range Radio General InformationConnection Audio Alarm Verification AAV Wiring ConnectionsProgramming Connection Of AAV Unit When Not Using a 4285 Phone module Calculating the Battery Size Needed Final Power UPTo bypass this delay, press # + ExampleDevice Current # Units Total Current Making the BatteryConnections Total =Programming the Descriptors Entering Zone Descriptors program menu modeSection PressO R Press 6 to accept the selected word Press 8 to save all words in memoryAlternate Method For Programming Zone Descriptors Method Alpha Vocabulary List For Adding Custom WordsSequential Mode For 5800 Series Wireless Transmitters Serial # ↑ Page System Communication Following describes each format in greater detailAdemco Contact ID Reporting takes the following format +1/4+1 Report Standard ExpandedCommunication Programming Table of Contact ID Event CodesPress 47 SPLIT/DUAL Reporting Press 45 Phone System Select Enter 1 digit default =Press 46 Report FORMAT, PRIMARY/SECONDARY To Primary Phone No To Secondary Phone NoPress 61 Bypass Report Code To Program System Status and Restore Report Codes 60 68, 70Press 60 Trouble Report Code Press 62 AC Loss Report CodePress 68 Cancel Report Code Press65 OPEN/EXIT Alarm Report CODE, 1st DigitsPress 67 RF XMTR. LOW Battery Report Code Press 70 Alarm Restore Report CODE, 1st DigitPress 92 Number of Reports in Armed Period Press 74 LOW BAT Restore Report CodePress 75 RF XMTR. LOW Battery Restore Code Press 94 Download Phone NumberTesting the System Test ProcedureTo the Installer To change the Duress code System OperationTo program a Duress code To delete the Duress codeDisarmed, Not Ready Features for Each Arming ModeKeypad Functions Forced Quick BypassRelay Outputs Keys Displayed as ZoneIf used Security Code + # +Trouble Conditions See Troubleshooting Guide also Troubleshooting Guide System including WirelessControl Please Before you call Technical Support, be sure youRead the Instructions VISTA-10SE Security Control Remote Keypad Specifications & AccessoriesSpecifications Remote KeypadsTransmitter Module Relay Module Phone ModuleZones With the Ademco VISTA-10SE Ademco 702 Outdoor Accessories Compatible DevicesNo CN SirenFederal Communications Commission FCC Part 15 Statement Federal Communications Commission FCC Part 68 StatementUL Notices Canadian Department of Communications DOC Statement Limitations of this Alarm System ADT VISTA-10SE Summary of Connections Ademco Limited Warranty
Top Page Image Contents