VistaQuest N7227V5 installation instructions Alarm

Page 40

The letter(s) in parentheses after each function described below, such as (A) after ACTION, are those that appear in the various summary displays of programmed data during programming.

ACTION (A) The "ACTION" of the relay is how the relay will respond when it is activated by the "START" programming. You may want the relay to activate momentarily, to pulse on and off continuously, or to remain activated until some other event occurs to stop it. There are four different choices of actions:

•ACTIVATE for 2 SECONDS and then reset.

•ACTIVATE and REMAIN ACTIVATED until stopped by some other event.

•PULSE ON and OFF until stopped by some other event.

•NOT USED when the relay is not used.

START (STT) The "START" programming determines when and under what conditions the relay will be activated. The following

START options are available:

A)1. EVENT (EV) is the condition (Alarm, Fault, Trouble) that must occur to a zone or group of zones (zone list) in order to activate the relay. These conditions apply only when a zone list is used. The different choices for "EVENT" are listed below and in the “Programming Output Relays” section that follows.

• ALARM

Relay action begins upon any alarm in an

 

assigned zone in the zone list.

• FAULT

Relay action begins upon any opening or

 

short in an assigned zone in the zone list.

•TROUBLE Relay action begins upon any trouble condition in an assigned zone in the zone list.

• NOT USED Relay action is not dependent upon one of the above events.

2.ZONE LIST (ZL) is a group of zones to which the “EVENT” applies in order to activate a particular relay. Note that there are a total of 3 zone lists that can be programmed in field ✱81 mode; when the selected EVENT (Alarm, Fault or Trouble) occurs in any zone in the selected “Start” ZONE LIST (1, 2, or 3), activation of the selected relay will

START.

B)1. ZONE TYPE/SYSTEM OPERATION (ZT). If a System Operation, such as “DISARMING” or “ANY FIRE ALARM,” is to activate the relay, the appropriate choice would also be entered under the “ZONE TYPE” option. “ZONE TYPE” is used independently of the “EVENT/ZONE LIST” combination.

If a specific "ZONE TYPE" is chosen, any zone of that re - sponse type going into alarm, trouble, or fault will cause the relay to activate as selected in "ACTION.” If the same “ZONE TYPE” is also chosen for the STOP programming, any zone of that type that restores will de-activate the relay.

If a "SYSTEM OPERATION" is chosen (e.g., End of Exit Time), that operation will cause the relay to activate as selected in "ACTION.” The different choices for "ZONE TYPE" and "SYSTEM OPERATION" are listed in “Programming Output Relays” later in this section, and in the Programming Form.

– 40 –

Page 39 Page 41
Image 40
Page 39 Page 41
Contents VISTA-10SE Recommendations For Smoke And Heat Detectors Recommendations For Proper Intrusion ProtectionTable of Contents Relay Output Devices Sequential Mode For 5800 Series Wireless Transmitters SectionList of Figures HOW to USE this Manual Conventions Used in this Manual Wireless Expansion General DescriptionAC Power Supply Back-Up BatteryOptional Phone module Supports the Ademco 4285 Phone module Communication FormatsInstalling the Lock if used Installing the ControlMounting the Cabinet Relay Unit if installed in cabinet Standard Phone Line Connections Standard Telephone Line ConnectionsWiring The AC Transformer Installing The Back-Up BatteryWiring Table Do not Connect the Wires to the Battery YETWiring To The Keypads Installing Remote KeypadsKeypads That May Be Used Mounting the Keypads Keypad Connections To The Control BoardPreliminary Check-out Procedure Using a Supplementary Power Supply For KeypadsBasic HARD-WIRED Zones Installing the Hard-Wired ZonesWiring Burglary and Panic Devices To Zones Wiring 4-Wire Smoke/Combustion Detectors on ZoneProgramming Hard-Wired Zones Zone Types Special Notes on Zone Check-Out Procedure For Hard-Wired ZonesProgramming Wireless RF Zone Expansion 5800 RF Systems Wireless Systems AvailableSeries Receiver Wireless Zones Wireless System Operation and Transmitter SupervisionTransmitter Battery Life Wireless System Installation AdvisoriesInstallation and Setup of the 4281/5881 Wireless Receivers Receiver SupervisionSeries Transmitter Setup BoardSetting the DIP Switches On 5700 SeriesRefer to the Compatible 5700 Series TransmittersDIP Switch Tables for 5700 RF System Wireless Devices Compatible 5700 Series Transmitters Model Product Zone/ID # DescriptionProgramming the Control For a 5700 Wireless System Using the House ID Sniffer Mode 5700 SystemsEnter your Installer Code + # + Zone Programming For 5700 TransmittersProgramming Guide Programming 5700 RF Enter the Installer Code + # +Systems Series Transmitter Setup Compatible 5800 Series Transmitters TempProgramming the RF Transmitters 5800 RF Systems GBDEnrolling 5800 Transmitters Into The System RF House ID CodeEnrolling Through Zone Programming ZN ZT RC In L 0 0 0 0 RF Recommend that you confirm the programming of every Transmitter before proceeding to the next zoneSniffer Mode Check-Out Procedure for Wireless ZonesTransmitter ID Go/No Go Test Relay Device Basics Relay Output DevicesRelay Modules Alarm Programming Output Relays Choices for Zone Types Example of Output Relay Programming Installing the Phone module Phone Module WiringPhone Module General InformationTerminal Connects to Caller ID UnitsWiring Notes 4285Programming The Control For Phone Access Press 95. Ring Detection CountVoice Answering Module Downloading Field 95 ProgrammingTo Check Phone module Operation From an On-Premises Phone Checking the Operation of the 4285 Phone moduleTo Check Phone module Operation From an Off-Premises Phone External Sounders Press 30. Alarm Bell Timeout Testing the SounderSounder Connections Press 51. Confirmation of Arming DingGeneral Information Long Range RadioConnection Wiring Connections Audio Alarm Verification AAVProgramming Connection Of AAV Unit When Not Using a 4285 Phone module Final Power UP To bypass this delay, press # +Calculating the Battery Size Needed ExampleMaking the Battery ConnectionsDevice Current # Units Total Current Total =Entering Zone Descriptors program menu mode SectionProgramming the Descriptors PressO R Press 8 to save all words in memory Press 6 to accept the selected wordAlternate Method For Programming Zone Descriptors Method Alpha Vocabulary List For Adding Custom WordsSequential Mode For 5800 Series Wireless Transmitters Serial # ↑ Page System Communication Following describes each format in greater detailAdemco Contact ID Reporting takes the following format +1/4+1 Report Standard ExpandedCommunication Programming Table of Contact ID Event CodesPress 45 Phone System Select Enter 1 digit default = Press 46 Report FORMAT, PRIMARY/SECONDARYPress 47 SPLIT/DUAL Reporting To Primary Phone No To Secondary Phone NoTo Program System Status and Restore Report Codes 60 68, 70 Press 60 Trouble Report CodePress 61 Bypass Report Code Press 62 AC Loss Report CodePress65 OPEN/EXIT Alarm Report CODE, 1st Digits Press 67 RF XMTR. LOW Battery Report CodePress 68 Cancel Report Code Press 70 Alarm Restore Report CODE, 1st DigitPress 74 LOW BAT Restore Report Code Press 75 RF XMTR. LOW Battery Restore CodePress 92 Number of Reports in Armed Period Press 94 Download Phone NumberTesting the System Test ProcedureTo the Installer System Operation To program a Duress codeTo change the Duress code To delete the Duress codeFeatures for Each Arming Mode Keypad FunctionsDisarmed, Not Ready Forced Quick BypassKeys Displayed as Zone If usedRelay Outputs Security Code + # +Trouble Conditions See Troubleshooting Guide also Troubleshooting Guide System including WirelessControl Before you call Technical Support, be sure you PleaseRead the Instructions Specifications & Accessories SpecificationsVISTA-10SE Security Control Remote Keypad Remote KeypadsRelay Module Phone Module Transmitter ModuleZones With the Ademco VISTA-10SE Accessories Compatible Devices No CNAdemco 702 Outdoor SirenFederal Communications Commission FCC Part 15 Statement Federal Communications Commission FCC Part 68 StatementUL Notices Canadian Department of Communications DOC Statement Limitations of this Alarm System ADT VISTA-10SE Summary of Connections Ademco Limited Warranty
Top Page Image Contents