Panasonic WV-CS954 RS485 Setup, Use, Enables X ON/X OFF data flow control, AUTO1, AUTO2

Page 20

RS485 SETUP

Use the following procedure to configure the RS485 setup when you want to use the system controller to control the camera (pan, tilt, etc.) via the camera's data port.

1.Display the setup menu (page 21), move the cursor to COMMUNICATION O, and then press the CAM (SET) button.

This will display the RS485 setup menu.

2.Check the unit number. (page 13)

The UNIT NUMBER item shows the unit number specified by DIP Switch 1. The factory default unit number is 1.

If DIP Switch 1 specifies 1 to 96 as the unit number, move the cursor to UNIT NUMBER and then tilt the joystick left or right to select a unit number (1 to 96).

** RS485 SETUP **

UNIT

NUMBER

1

 

SUB ADDRESS

-----

BAUD

RATE

19200

DATA

BIT

8

 

PARITY CHECK

NONE

STOP

BIT

1

 

XON/XOFF

NOT USE

WAIT

TIME

OFF

ALARM DATA

AUTO2

DELAY TIME

OFF

RET

TOP

 

 

Note: It is not necessary to configure the RS485 SET UP menu SUB ADDRESS setting.

3.Move the cursor to BAUD RATE, and then tilt the joystick left or right to select a baud rate setting. Tilting the joystick cycles through the baud rate (transmission speed) display in the sequence shown below. (unit: bits/s) The factory default setting is 19200.

2400 4800 9600 19200

4.Move the cursor to DATA BIT, and then tilt the joystick left or right to select a data bit setting (7 or 8).

The factory default setting is 8.

5.Move the cursor to PARITY CHECK, and then tilt the joystick left or right to select a parity bit setting (NONE, ODD, EVEN).

The factory default setting is NONE.

6.Move the cursor to STOP BIT, and then tilt the joystick left or right to select a stop bit setting (1 or 2).

The factory default setting is 1.

7.Move the cursor to XON/XOFF, and then tilt the joystick left or right to select an XON/XOFF setting.

The factory default setting is NOT USE.

NOT USE: Disables X ON/X OFF data flow control.

USE

: Enables X ON/X OFF data flow control.

8.Move the cursor to WAIT TIME, and then tilt the joystick left or right to select a wait time setting.

The wait time is the time that the camera should wait before resending data when no receive acknowledgement (ACK) is returned after data is sent.

Tilting the joystick cycles through the wait time display in the sequence shown below. (unit: ms) The factory default setting is OFF.

OFF ↔ 100MS ↔ 200MS ↔ 400MS ↔ 1000MS

9.Move the cursor to ALARM DATA, and then tilt the joystick left or right to select an alarm data send mode setting.

POLLING : Sends alarm data in response to a request by the system controller.

AUTO1

: Sends alarm data each time an alarm

 

signal is input.

AUTO2

: Sends alarm data at five-second intervals.

 

This is the factory default setting.

10.Move the cursor to DELAY TIME, and then tilt the joystick left or right to select a delay time setting. The delay time is the time is the time the camera should wait before sending a receive acknowledge (ACK). The delay time display changes in the sequence shown below. (unit: ms) The factory default setting is OFF.

OFF ↔ 100MS

This setting can be configured only when 2-line configuration is selected by DIP Switch 2. (page 12)

-20-

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Color Cctv Camera English Version Important Safety Instructions EnglishDisclaimer of Warranty Limitation of LiabilityOptional Accesories FeaturesAccesories Precautions Operating Precautions Self-diagnosing Function Contents Construction Ensuring Trouble-free OperationInstallation Precautions Beware of high humidity DIP Switch SettingsCommunication Parameters DIP Switch Unit Number DIP Switch RS485 Communication Parameters DIP Switch DIP Switch Unit NumberCamera Installation Installing the CameraBack Removing the Decorative Camera Uninstalling the CameraUninstalling the Camera Connections How to Assemble the Cable with the Accessory Connector Connect this to 24 V AC Class 2 Power Supply onlyRS485 Setup Enables X ON/X OFF data flow controlUSE AUTO1Using the Setup Menu Displaying the Setup MenuLanguage Setting When using the WV-CU650ALC Camera SettingsUsing the Camera Setup Menu When SUPER-D 3 is turned off When SUPER-D 3 is turned onShutter Speed Shutter OFF ↔ AutoOFF Adjusting the Phase for Line-lock SynchronizationOn MID Resolution Resolution Black and White Mode BW ModeBetween the color mode and the black White mode in accordance with pictureAuto Focus AF Mode ExampleZoom Limit Zoom Limit Auto Image Stabilizer StabilizerUsing the Pan/Tilt Setup Menu Position Setting Position SETPosition Number Selection Preset PAN / TiltPreset ID Setting Preset ID Auto Focus AF Mode Preset Speed Setting Preset SpeedScene File Setting Scene File Light Control ALC/MANUALDeleting a Preset Position DEL Configuring Auto PAN Detailed Settings PAN LimitAuto PAN Key Setting Auto PAN KEY Patrol Function Setting PatrolPrivacy Zone Setting Privacy Zone Image Hold Setting Image HoldDigital Flip Setting Digital Flip Proportional Pan/Tilt Setting PROPO. P/TArea Title Setting Area Title On UserTilt Angle Setting Tilt Angle Cleaning Settings CleaningAlarm Settings Using the Alarm Setup MenuConfiguring Detailed Motion Detector Settings for Mode ModePATROL1 1POSIAutopan Alarm 2POSIPATROL2 3POSISpecial Settings Using the Special Setup MenuAdjusting Picture Quality To delete a blemish compensation patternScene Select Settings Scene Select SettingUsing the Scene Select Setting Menu Quick Menu Settings Displaying the Quick Setup MenuPassword Settings Password Lock SettingsTurning Password Lock On and Off Changing the PasswordOK Reset RET TOP Controller Operation Setting ShortcutsIris Close Troubleshooting FIXProblem 37-38 36-37 Periodically check the power cord and plug Specifications GeneralPan and Tilt LensMain Functions Version Français Instructions DE Sécurité Importantes Limitation DE Responsabilité Déni DE LA GarantieDéni DE LA Garantiecaractéristiques AccessoiresAccessoires EN Option Mesures DE Précautions Précautions Pendant LE Fonctionnement Que faire si le message Over Heat apparaît sur l’écranNe pas mouiller la caméra Nettoyage de la caméra vidéoFonction d’auto-diagnostic Installation DE LA Caméra Vidéo Utilisation DU Menu DE ConfigurationRéglages DE LA Caméra Vidéo PAN/AZIMUTHObjectif ’objectif ne peut pas être remplacé Fonctionnement sans problèmePrécautions Pour L’INSTALLATION Emplacement et installation de la caméraLes vis doivent être commandées séparément Câblage de la caméra vidéoRéglages DES Interrupteurs DIP Paramètres de communications Interrupteur DIPÉmission de chaleur Degré d’humidité élevéNuméro de caméra vidéo déterminé Interrupteur DIP CaméraParamètres de communication RS485 Interrupteur DIP Interrupteur DIP Numéro deInstallation DE LA Caméra Vidéo Installation de la caméra vidéoBague du fil de sécurité Enlever la caméra vidéo Enlever LA CaméraRetrait du couvercle décoratif Capacités entrée/sortie d’alarme Informations relatives aux connecteurs accessoiresBranchements Mesures de précautionsComment assembler le câble et le connecteur acces- soire RS485 Ajust UtiliseActive le contrôle de flux de données ON/X OFFRéglage de langue Utilisation DU Menu DE ConfigurationAffichage du menu de configuration Réglages DE LA Caméra Vidéo Utilisation du menu de réglage de la CaméraOUI OUI Eleve OUI BASOUI Moyen Résolution Résolution Mode noir et blanc Mode NBSélectionne le mode noir et blanc Sélectionne le mode couleurMode de mise au point automatique Mode AF ExempleLimite de réglage de zoom Limite Zoom Stabilisateur d’images automatiquePAN/AZIMUTH Sélection du numéro de position PrepoZOOM/FOCUS PAN/AZIMUTHContrôle de lumière ALC/MANUEL Orig SÉQTRI SuivConfiguration des réglages détaillés d’AUTO PAN DemarageLimit PAN PAN/AZIMUTH ∑BOUTON SET ZOOM/FOCUS ∑BOUTON SET Maintien d’Image Image Memo 12 Réglage du titre de zone Titre ZoneTitre Zoneutil 14 Réglages de nettoyage Nettoyage Réglages DE L’ALARME Utilisation du menu de réglage de ’alarme1POSITION PATR12POSITION PATR23POSITION PATR3Pour effacer un motif de compensation d’imperfections Réglages SpéciauxUtilisation du menu de réglage spécial Auto Élevé BAL BLC PERM2 Réglage DE Sélection DE ScèneUtilisation du menu de réglage de Sélection de scène Réglages DU Menu Rapide Affichage du menu de réglage rapideRéglages DU MOT DE Passe Réglages du verrouillage du mot de Passe MOT DE PasseNouveau MOT PASSE? Raccourcis Opération du contrôleur RéglageIris Fermer EN CAS DE Problèmes ProblèmeCause et action recommandée 88-89 87-88 Problème Caractéristiques Techniques Vision Nuit OFF CAG ÉlevéCAG OUI BAS, OUI MOYEN, OUI ELEVE, OFF OFF, SÉQ, TRI, Auto PAN, PATR, Suivi AutoSÉQ, TRI, Auto PAN, PATR, Suivi Auto OUI/OFF103 Imprimé au Japon

WV-CS954 specifications

The Panasonic WV-CS954 is a sophisticated and versatile CCTV camera designed for high-performance surveillance applications. This model is equipped with advanced features that make it ideal for various environments, whether indoor or outdoor.

One of the standout characteristics of the WV-CS954 is its exceptional image quality. The camera utilizes a high-resolution 1/3-inch CCD sensor that delivers crisp and clear images with a resolution of 540 TV lines. This ensures that even the finest details are captured, enabling effective monitoring and identification of subjects in various lighting conditions.

The WV-CS954 is also equipped with a powerful 10x optical zoom lens, enabling users to zoom in on subjects without sacrificing image clarity. This feature is particularly useful in scenarios where details are crucial, such as monitoring entry points or observing large areas. The camera also incorporates a digital zoom capability, which further extends its versatility for surveillance needs.

In terms of technology, the WV-CS954 integrates advanced features such as auto focus and auto iris functions, enhancing its performance in fluctuating light conditions. These technologies help maintain optimal exposure and sharpness, ensuring reliable operation regardless of the environment.

Another notable feature of the WV-CS954 is its pan and tilt capability. The camera can be remotely controlled to pan 360 degrees and tilt up to 180 degrees, offering flexible coverage of expansive areas. This allows operators to monitor large spaces efficiently, making it an excellent choice for retail stores, parking lots, and other open environments.

The camera is also designed with durability in mind. Its robust construction and weather-resistant design make it suitable for outdoor use, capable of withstanding various environmental challenges. Additionally, the WV-CS954 is compatible with various mounting options, further enhancing its adaptability in different settings.

For connectivity, the WV-CS954 supports both analog and digital interface options, making it easy to integrate into existing security systems. It is also compatible with Panasonic's comprehensive suite of video management software, enabling seamless surveillance operations.

In conclusion, the Panasonic WV-CS954 is a reliable and feature-rich surveillance camera that offers exceptional image quality, flexible monitoring capabilities, and robust design. Its advanced technologies and user-friendly features make it a top choice for security professionals looking to enhance their surveillance solutions.
Top Page Image Contents