Panasonic WV-CS954 operating instructions Deleting a Preset Position DEL

●Deleting a Preset Position (DEL)

1.Move the cursor to DEL, and then press the CAM (SET) button.

This deletes the contents of the currently selected position number and displays the position selection menu.

		PRESET NO.			1*
POSITION SET
PRESET ID				ON
ALC/MANUAL				ALC
AF MODE				MANUAL L
DWELL TIME				10S
SCENE FILE				OFF
PRESET SPEED				••••••••I
				L	H
RET TOP
			DEL
	**PRESET POSITION**
	1	2*		3*	4*
5*		6*		7*	8*
9*		10*		11*	12*
13*		14*		15*	16*
17*		18*		19*	20*
21*		22*		23*	24*
25*		26*		27*	28*
29*		30*		31*	32*

ID:DOOR 033-064 225-256

RET TOP

(3) Home Position Setting (HOME POSITION)

A currently configured preset position can be designated as the home position.

Pressing the HOME button of the system controller will cause the camera to move to the currently specified home position. Use the following procedure to make a preset position the home position.

1.Move the cursor to HOME POSITION, and then tilt the joystick left or right to select the position number of the preset position you want to make the home position.

This causes the preset position whose position number you select to become the home position. If you do not want to use the home position function, select OFF for the HOME POSITION setting.

(4) Self Return Setting (SELF RETURN)

The self return setting can be used to specify automatic return to a particular mode if a certain amount of time elapses without any operation being performed.

1.Move the cursor to SELF RETURN, and then tilt the joystick left or right to select a self return trigger setting. Tilting the joystick cycles through the self return display in the sequence shown below. (unit: sec, min)

OFF ↔ 1S ↔ 2S ↔ 3S ↔ ....... ↔ 10S ↔ 20S ↔ 30S ↔ 40S

↔	↔
60MIN	50S
↔	↔
30MIN ↔ 20MIN ↔	10MIN ↔ 5MIN ↔ 3MIN ↔ 2MIN ↔ 1MIN

2.If you selected any setting other than OFF in step 1, press the CAM (SET) button and then tilt the joystick left or right to select a self return mode.

OFF ↔ AUTO ↔ HOME ↔ APAN ↔ SEQ ↔ SORT

TRK ↔ PTR4 ↔ PTR3 ↔ PTR2 ↔ PTR1

OFF	: In the auto mode, exits the auto mode
	when the trigger time elapses.

AUTO (AUTO MODE setting not OFF) : Returns to the auto mode when the trigger time elapses.

AUTO (AUTO MODE setting OFF) : Returns to the home position when the trigger time

	elapses.
HOME	: Returns to the home position when the
	trigger time elapses.
APAN	: Activates auto pan when the trigger
	time elapses.
SEQ	: Activates the sequence function when
	the trigger time elapses.
SORT	: Activates the sort function when the
	trigger time elapses.

PTR 1 to 4: Activates the patrol function when the

	trigger time elapses.
TRK	: After the trigger time elapses, the
	camera returns to the home position
	and then automatic tracking starts.
	Following that, after a set time, the
	camera returns to the home position
	and starts to continue automatic
	tracking.

Note: The HOME setting should be selected when you want to normally leave the camera in the home position and occasionally perform pan and tilt, or when you want to activate SEQ.

(5) Auto Mode Setting (AUTO MODE)

Use the auto mode setting to specify the camera movement mode (OFF, SEQ, SORT, AUTO PAN, PATROL 1~4, AUTO TRACK).

After selecting AUTO PAN, you can use the AUTO PAN setting menu to configure detailed settings.

1.Move the cursor to AUTO MODE, and then tilt the joystick left or right to select a camera movement mode setting.

OFF	: Manual movement only
SEQ	: Sequentially		switches	between
	preset	positions in		position
	number	sequence.		(sequential
	movement)
SORT	: Sequentially		switches	between
	preset positions counterclockwise,
	starting from the camera home
	position. (sort movement)
AUTO PAN	: Camera pans automatically within
	the range specified by PAN.
	Selecting AUTO PAN and pressing
	the CAM (SET) button will display

the AUTO PAN setting menu, which can be used for configuring detailed settings. (page 31)

PATROL 1 to 4 : Operates the camera in accordance with patrol function settings.

-30-