Panasonic WV-CS954 Adjusting the Phase for Line-lock Synchronization, On MID, Off

Page 24

Notes:

When AUTO is selected for the shutter setting, fluorescent lighting may cause flickering of the picture. If this happens, select OFF or 1/100 for the shutter speed setting.

AUTO is disabled when MANUAL is selected for light control (ALC/MANUAL) and FIX is selected for electronic sensitivity enhancement (SENS UP).

(4)Gain Control (AGC)

1.Move the cursor to AGC, and then tilt the joystick left or right to select a gain control setting.

ON (LOW) : Low gain

ON (MID)

: Medium gain

ON (HIGH) : High gain

OFF

: Fixed gain

Note: When AGC is turned on, the noise reduction function automatically activates under low illumination to reduce digital noise. This also, however, can cause afterimages to be generated by moving objects, and by panning and tilting the camera. For more information, see the DNR setting (page 25).

(5)Electronic Sensitivity Enhancement (SENS UP)

1. Move the cursor to SENS UP, and then tilt the joystick left or right to select an electronic sensitivity enhancement setting.

The electronic sensitivity enhancement setting can be changed only when OFF or AUTO is selected for the shutter speed (SHUTTER) setting. Tilting the joystick cycles through the settings display in the sequence shown below.

When SUPER-D 3 is turned off

OFF X2 AUTO X4 AUTO X6 AUTO X10 AUTO X16 AUTO

 

 

 

 

X32 FIX

 

 

 

X32 AUTO

X10 FIX

X6 FIX

X4 FIX

X2 FIX

X16 FIX

OFF

When SUPER-D 3 is turned on

OFF X2 AUTO X4 AUTO X6 AUTO

X32 AUTO X16 AUTO X10 AUTO

Note: The following are the differences between AUTO and FIX.

AUTO: Selecting X32 AUTO, for example, automatically increases sensitivity, up to a maximum of 32 times.

FIX : Selecting X32 FIX, for example, increases sensitivity 32 times.

The FIX settings cannot be selected when the shutter speed (SHUTTER) setting is 1/100.

Caution: Turning on SENS UP can cause digital noise and white spots (blemish) to appear in the picture.

(6) Synchronization (SYNC)

This camera supports the following three sync modes, which are listed in priority sequence from highest priority to lowest.

-24-

(1)Multiplexed vertical drive (VD2)

(2)Internal sync (INT)

(3)Line-lock (LL)

Input of a multiplexed vertical driver (VD2) signal automatically switches to VD2 sync, regardless of the camera's current sync mode (SYNC). In this case, the camera setting menu shows EXT (VD2) for the SYNC setting, which cannot be changed to internal sync (INT) or line-lock (LL).

The following procedures explain how to select internal sync (INT) and line-lock sync (LL), and how to perform phase adjustment when line-lock sync (LL) is selected.

1.Move the cursor to SYNC, and then tilt the joystick left or right to select the sync mode.

INT : Internal sync

LL: Line-lock (Cannot be used in areas with 50 Hz power.)

Selecting LL and pressing the CAM (SET) button will display the SYNC setting menu, which can be used for configuring detailed settings. (This page)

Adjusting the Phase for Line-lock Synchronization

Connect the video output signal of the camera being adjusted and the reference video output signal to a two-input oscilloscope.

Set the oscilloscope to the vertical rate, and then expand the vertical sync portion on the oscilloscope.

1.Move the cursor to COARSE, and then tilt the joystick left or right to align the coarse adjustment of the vertical phases of the camera being adjusted with that of the reference camera.

Coarse adjustment be performed across 16 steps (1 through 16). Adjusting past step 16 returns to step 1.

 

** SYNC **

V PHASE

 

 

COARSE

 

1(1--16)

FINE

••••I••••

 

-

+

RET TOP

2.Move the cursor to FINE, and then tilt the joystick left or right to align the fine adjustment of the vertical phases of the camera being adjusted with that of the reference camera.

Notes:

To reset COARSE and FINE to the preset values, press the F2 button. For WV-RM70, press the right and left switches simultaneously. COARSE is preset to zero-crossing of the AC line phase.

If the AC line phase contains spike noise, etc., the vertical phase of the video output signal may be disturbed.

Image 24
Contents Color Cctv Camera English Version Important Safety Instructions EnglishDisclaimer of Warranty Limitation of LiabilityFeatures AccesoriesOptional Accesories Precautions Operating Precautions Self-diagnosing Function Contents Construction Ensuring Trouble-free OperationInstallation Precautions DIP Switch Settings Communication Parameters DIP SwitchBeware of high humidity Unit Number DIP Switch RS485 Communication Parameters DIP Switch DIP Switch Unit NumberCamera Installation Installing the CameraBack Uninstalling the Camera Uninstalling the CameraRemoving the Decorative Camera Connections How to Assemble the Cable with the Accessory Connector Connect this to 24 V AC Class 2 Power Supply onlyRS485 Setup Enables X ON/X OFF data flow controlUSE AUTO1Using the Setup Menu Displaying the Setup MenuLanguage Setting When using the WV-CU650Camera Settings Using the Camera Setup MenuALC When SUPER-D 3 is turned off When SUPER-D 3 is turned onShutter Speed Shutter OFF ↔ AutoAdjusting the Phase for Line-lock Synchronization On MIDOFF Resolution Resolution Black and White Mode BW ModeBetween the color mode and the black White mode in accordance with pictureAuto Focus AF Mode ExampleZoom Limit Zoom Limit Auto Image Stabilizer StabilizerUsing the Pan/Tilt Setup Menu Position Setting Position SETPosition Number Selection Preset PAN / TiltPreset ID Setting Preset ID Auto Focus AF Mode Preset Speed Setting Preset SpeedScene File Setting Scene File Light Control ALC/MANUALDeleting a Preset Position DEL Configuring Auto PAN Detailed Settings PAN LimitAuto PAN Key Setting Auto PAN KEY Patrol Function Setting PatrolPrivacy Zone Setting Privacy Zone Image Hold Setting Image HoldDigital Flip Setting Digital Flip Proportional Pan/Tilt Setting PROPO. P/TArea Title Setting Area Title On UserTilt Angle Setting Tilt Angle Cleaning Settings CleaningAlarm Settings Using the Alarm Setup MenuConfiguring Detailed Motion Detector Settings for Mode Mode1POSI AutopanPATROL1 Alarm 2POSIPATROL2 3POSISpecial Settings Using the Special Setup MenuAdjusting Picture Quality To delete a blemish compensation patternScene Select Setting Using the Scene Select Setting MenuScene Select Settings Quick Menu Settings Displaying the Quick Setup MenuPassword Settings Password Lock SettingsTurning Password Lock On and Off Changing the PasswordOK Reset RET TOP Controller Operation Setting ShortcutsIris Close Troubleshooting FIXProblem 37-38 36-37 Periodically check the power cord and plug Specifications GeneralPan and Tilt LensMain Functions Version Français Instructions DE Sécurité Importantes Limitation DE Responsabilité Déni DE LA GarantieAccessoires Accessoires EN OptionDéni DE LA Garantiecaractéristiques Mesures DE Précautions Précautions Pendant LE Fonctionnement Que faire si le message Over Heat apparaît sur l’écranNe pas mouiller la caméra Nettoyage de la caméra vidéoFonction d’auto-diagnostic Installation DE LA Caméra Vidéo Utilisation DU Menu DE ConfigurationRéglages DE LA Caméra Vidéo PAN/AZIMUTHObjectif ’objectif ne peut pas être remplacé Fonctionnement sans problèmePrécautions Pour L’INSTALLATION Emplacement et installation de la caméraLes vis doivent être commandées séparément Câblage de la caméra vidéoRéglages DES Interrupteurs DIP Paramètres de communications Interrupteur DIPÉmission de chaleur Degré d’humidité élevéNuméro de caméra vidéo déterminé Interrupteur DIP CaméraParamètres de communication RS485 Interrupteur DIP Interrupteur DIP Numéro deInstallation DE LA Caméra Vidéo Installation de la caméra vidéoBague du fil de sécurité Enlever LA Caméra Retrait du couvercle décoratifEnlever la caméra vidéo Capacités entrée/sortie d’alarme Informations relatives aux connecteurs accessoiresBranchements Mesures de précautionsComment assembler le câble et le connecteur acces- soire RS485 Ajust UtiliseActive le contrôle de flux de données ON/X OFFUtilisation DU Menu DE Configuration Affichage du menu de configurationRéglage de langue Réglages DE LA Caméra Vidéo Utilisation du menu de réglage de la CaméraOUI OUI BAS OUI MoyenOUI Eleve Résolution Résolution Mode noir et blanc Mode NBSélectionne le mode noir et blanc Sélectionne le mode couleurMode de mise au point automatique Mode AF ExempleLimite de réglage de zoom Limite Zoom Stabilisateur d’images automatiquePAN/AZIMUTH Sélection du numéro de position PrepoZOOM/FOCUS PAN/AZIMUTHContrôle de lumière ALC/MANUEL Orig SÉQTRI SuivConfiguration des réglages détaillés d’AUTO PAN DemarageLimit PAN PAN/AZIMUTH ∑BOUTON SET ZOOM/FOCUS ∑BOUTON SET Maintien d’Image Image Memo 12 Réglage du titre de zone Titre ZoneTitre Zoneutil 14 Réglages de nettoyage Nettoyage Réglages DE L’ALARME Utilisation du menu de réglage de ’alarme1POSITION PATR12POSITION PATR23POSITION PATR3Réglages Spéciaux Utilisation du menu de réglage spécialPour effacer un motif de compensation d’imperfections Réglage DE Sélection DE Scène Utilisation du menu de réglage de Sélection de scèneAuto Élevé BAL BLC PERM2 Réglages DU Menu Rapide Affichage du menu de réglage rapideRéglages DU MOT DE Passe Réglages du verrouillage du mot de Passe MOT DE PasseNouveau MOT PASSE? Raccourcis Opération du contrôleur RéglageIris Fermer EN CAS DE Problèmes ProblèmeCause et action recommandée 88-89 87-88 Problème Caractéristiques Techniques Vision Nuit OFF CAG ÉlevéCAG OUI BAS, OUI MOYEN, OUI ELEVE, OFF OFF, SÉQ, TRI, Auto PAN, PATR, Suivi AutoSÉQ, TRI, Auto PAN, PATR, Suivi Auto OUI/OFF103 Imprimé au Japon

WV-CS954 specifications

The Panasonic WV-CS954 is a sophisticated and versatile CCTV camera designed for high-performance surveillance applications. This model is equipped with advanced features that make it ideal for various environments, whether indoor or outdoor.

One of the standout characteristics of the WV-CS954 is its exceptional image quality. The camera utilizes a high-resolution 1/3-inch CCD sensor that delivers crisp and clear images with a resolution of 540 TV lines. This ensures that even the finest details are captured, enabling effective monitoring and identification of subjects in various lighting conditions.

The WV-CS954 is also equipped with a powerful 10x optical zoom lens, enabling users to zoom in on subjects without sacrificing image clarity. This feature is particularly useful in scenarios where details are crucial, such as monitoring entry points or observing large areas. The camera also incorporates a digital zoom capability, which further extends its versatility for surveillance needs.

In terms of technology, the WV-CS954 integrates advanced features such as auto focus and auto iris functions, enhancing its performance in fluctuating light conditions. These technologies help maintain optimal exposure and sharpness, ensuring reliable operation regardless of the environment.

Another notable feature of the WV-CS954 is its pan and tilt capability. The camera can be remotely controlled to pan 360 degrees and tilt up to 180 degrees, offering flexible coverage of expansive areas. This allows operators to monitor large spaces efficiently, making it an excellent choice for retail stores, parking lots, and other open environments.

The camera is also designed with durability in mind. Its robust construction and weather-resistant design make it suitable for outdoor use, capable of withstanding various environmental challenges. Additionally, the WV-CS954 is compatible with various mounting options, further enhancing its adaptability in different settings.

For connectivity, the WV-CS954 supports both analog and digital interface options, making it easy to integrate into existing security systems. It is also compatible with Panasonic's comprehensive suite of video management software, enabling seamless surveillance operations.

In conclusion, the Panasonic WV-CS954 is a reliable and feature-rich surveillance camera that offers exceptional image quality, flexible monitoring capabilities, and robust design. Its advanced technologies and user-friendly features make it a top choice for security professionals looking to enhance their surveillance solutions.