Panasonic WV-CS954 operating instructions 1POSI, Autopan, PATROL1

Page 37

6.Move the cursor to DWELL TIME, and then tilt the joystick left or right to select an alarm detect dwell time setting.

After alarm detection, the next alarm is not detected until the specified dwell time elapses.

Tilting the joystick cycles through the setting display in the sequence shown below. (unit: sec)

2S ↔ 5S ↔ 10S ↔ 30S

7.Move the cursor to RECOVER TIME, and then tilt the joystick left or right to select an alarm reset time setting.

Tilting the joystick cycles through the setting display in the sequence shown below. (unit: sec, min)

If you set OFF, then it does not reset until some other operation is done. If AUTO TRACK is set, the camera starts automatic tracking when change (movement) is detected in the image during SEQ or SORT.

OFF ↔ 1MIN ↔ 2MIN ↔ 3MIN ↔ 5MIN ↔ 10MIN

AUTO TRACK ↔ 60MIN ↔ 30MIN ↔ 20MIN

Notes:

•Monitoring is usually done in SEQ mode, and when the camera detects change (movement) automatic tracking starts. To have the camera return to SEQ mode after a certain amount of time, set the SELF RETURN setting to SEQ.

•Use the mask setting to mask areas where there is wind movement of curtains, etc.

•Use a lower sensitivity level (LEVEL) setting for areas where illumination is low and prone to digital noise. Also note that operation error can occur when the illuminance of a subject is changed suddenly by the headlights of passing cars, turning lights on or off, etc.

•There is a delay of about 0.2 second from the point that the camera detects change (movement) in the image and the point that a signal is sent to the alarm terminal of a VCR, etc.

•Alarms are not output while the setting menu is displayed, unless demo mode alarm output is turned on.

•Alarms are not output when PAN, TILT, ZOOM, FOCUS or other functions are operating.

•When the motion detector is set to MODE 1 or MODE 2, it outputs alarm data during the blanking period. This can cause operational problems for a VCR or other device that uses a time code signal, etc. Turn off the motion detector when not using coaxial communication.

•The motion detector is not intended for use as specialty device for the prevention of theft, fire, etc. The manufacturer assumes no responsibility for any accidents that occur or any losses incurred while this product is being used.

(2)Preset Alarm Setting (PRESET ALM)

Turning on the preset alarm will output an alarm from the video output port or alarm output connector when the camera completes a move to a preset position. An

alarm is output in the following cases.

-37-

•When the self return function is activated (page 30) and the camera finishes moving to the home position, and when switching to the auto mode.

•When SEQ is selected for the auto mode (page 30), and the camera completes a move to a preset position during sequential movement

•When SORT is selected for the auto mode (page 30), and the camera completes a move to a preset position during SORT movement

•When AUTO PAN is selected for the auto mode (page 30), and the camera completes a preset move up to the AUTO PAN start point

•When the camera completes a move to a preset position during manual operation

•When PLAY is selected for the auto mode (page 32), and the camera completes a preset move up to the patrol start point

Use the following procedures to configure preset alarm settings

1.Move the cursor to PRESET ALM, and then tilt the joystick left or right to toggle it on and off.

ON : Turns on the preset alarm function.

OFF : Turns off the preset alarm function.

Note: Turn off the preset alarm function before downloading or uploading preset data.

(3) Alarm Input/Output (ALARM IN/OUT)

Use this setting to specify what operation the camera should perform when it an alarm signal is input to the alarm input connector or output from the alarm output connector.

Note: While the camera is in the AF mode or the lens moves between WIDE and TELE, alarm input may be ignored if several alarm inputs are received in succession.

1.Move the cursor to the ALARM IN/OUT O and then press the CAM (SET) button.

This will display the alarm setting menu.

2.Move the cursor to ALARM IN 1, and then tilt the joystick left and right to select the operation the camera should perform when an external signal is

received by ALARM IN 1.

OFF

: Ignore alarm input signals.

1POSI

: Move to preset position 1.

AUTOPAN

: Start auto pan.

PATROL1

: Start PATROL 1.

PATROL1 (S) : Start PATROL 1, and maintain the stored picture quality settings (page 32) even after completion.

AUTOTRACK1 : Move to preset position number 1, and then perform auto tracking.

**ALARM IN/OUT**

ALARM IN1

OFF

 

ALARM IN2

OFF

 

ALARM IN3

OFF

ALARM IN4

OFF

CNT-CLS 1

OFF

TIME OUT

100MS

CNT-CLS 2

OFF

COAX ALM OUT

OFF

RET TOP

 

 

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Color Cctv Camera English Version English Important Safety InstructionsLimitation of Liability Disclaimer of WarrantyAccesories FeaturesOptional Accesories Precautions Operating Precautions Self-diagnosing Function Contents Ensuring Trouble-free Operation ConstructionInstallation Precautions Communication Parameters DIP Switch DIP Switch SettingsBeware of high humidity Unit Number DIP Switch DIP Switch Unit Number RS485 Communication Parameters DIP SwitchInstalling the Camera Camera InstallationBack Uninstalling the Camera Uninstalling the CameraRemoving the Decorative Camera Connections Connect this to 24 V AC Class 2 Power Supply only How to Assemble the Cable with the Accessory ConnectorEnables X ON/X OFF data flow control RS485 SetupUSE AUTO1Displaying the Setup Menu Using the Setup MenuLanguage Setting When using the WV-CU650Using the Camera Setup Menu Camera SettingsALC When SUPER-D 3 is turned on When SUPER-D 3 is turned offShutter Speed Shutter OFF ↔ AutoOn MID Adjusting the Phase for Line-lock SynchronizationOFF Black and White Mode BW Mode Resolution ResolutionBetween the color mode and the black White mode in accordance with pictureExample Auto Focus AF ModeZoom Limit Zoom Limit Auto Image Stabilizer StabilizerPosition Setting Position SET Using the Pan/Tilt Setup MenuPosition Number Selection Preset PAN / TiltPreset ID Setting Preset ID Preset Speed Setting Preset Speed Auto Focus AF ModeScene File Setting Scene File Light Control ALC/MANUALDeleting a Preset Position DEL PAN Limit Configuring Auto PAN Detailed SettingsPatrol Function Setting Patrol Auto PAN Key Setting Auto PAN KEYImage Hold Setting Image Hold Privacy Zone Setting Privacy ZoneProportional Pan/Tilt Setting PROPO. P/T Digital Flip Setting Digital FlipArea Title Setting Area Title On UserCleaning Settings Cleaning Tilt Angle Setting Tilt AngleUsing the Alarm Setup Menu Alarm SettingsConfiguring Detailed Motion Detector Settings for Mode ModeAutopan 1POSIPATROL1 2POSI AlarmPATROL2 3POSIUsing the Special Setup Menu Special SettingsAdjusting Picture Quality To delete a blemish compensation patternUsing the Scene Select Setting Menu Scene Select SettingScene Select Settings Displaying the Quick Setup Menu Quick Menu SettingsPassword Lock Settings Password SettingsTurning Password Lock On and Off Changing the PasswordOK Reset RET TOP Shortcuts Controller Operation SettingIris Close FIX TroubleshootingProblem 37-38 36-37 Periodically check the power cord and plug General SpecificationsPan and Tilt LensMain Functions Version Français Instructions DE Sécurité Importantes Déni DE LA Garantie Limitation DE ResponsabilitéAccessoires EN Option AccessoiresDéni DE LA Garantiecaractéristiques Mesures DE Précautions Que faire si le message Over Heat apparaît sur l’écran Précautions Pendant LE FonctionnementNe pas mouiller la caméra Nettoyage de la caméra vidéoFonction d’auto-diagnostic Utilisation DU Menu DE Configuration Installation DE LA Caméra VidéoRéglages DE LA Caméra Vidéo PAN/AZIMUTHFonctionnement sans problème Objectif ’objectif ne peut pas être remplacéEmplacement et installation de la caméra Précautions Pour L’INSTALLATIONLes vis doivent être commandées séparément Câblage de la caméra vidéoParamètres de communications Interrupteur DIP Réglages DES Interrupteurs DIPÉmission de chaleur Degré d’humidité élevéCaméra Numéro de caméra vidéo déterminé Interrupteur DIPInterrupteur DIP Numéro de Paramètres de communication RS485 Interrupteur DIPInstallation de la caméra vidéo Installation DE LA Caméra VidéoBague du fil de sécurité Retrait du couvercle décoratif Enlever LA CaméraEnlever la caméra vidéo Informations relatives aux connecteurs accessoires Capacités entrée/sortie d’alarmeBranchements Mesures de précautionsComment assembler le câble et le connecteur acces- soire Utilise RS485 AjustActive le contrôle de flux de données ON/X OFFAffichage du menu de configuration Utilisation DU Menu DE ConfigurationRéglage de langue Utilisation du menu de réglage de la Caméra Réglages DE LA Caméra VidéoOUI OUI Moyen OUI BASOUI Eleve Mode noir et blanc Mode NB Résolution RésolutionSélectionne le mode noir et blanc Sélectionne le mode couleurExemple Mode de mise au point automatique Mode AFLimite de réglage de zoom Limite Zoom Stabilisateur d’images automatiqueSélection du numéro de position Prepo PAN/AZIMUTHPAN/AZIMUTH ZOOM/FOCUSContrôle de lumière ALC/MANUEL SÉQ OrigTRI SuivDemarage Configuration des réglages détaillés d’AUTO PANLimit PAN PAN/AZIMUTH ∑BOUTON SET ZOOM/FOCUS ∑BOUTON SET 12 Réglage du titre de zone Titre Zone Maintien d’Image Image MemoTitre Zoneutil 14 Réglages de nettoyage Nettoyage Utilisation du menu de réglage de ’alarme Réglages DE L’ALARMEPATR1 1POSITIONPATR2 2POSITION3POSITION PATR3Utilisation du menu de réglage spécial Réglages SpéciauxPour effacer un motif de compensation d’imperfections Utilisation du menu de réglage de Sélection de scène Réglage DE Sélection DE ScèneAuto Élevé BAL BLC PERM2 Affichage du menu de réglage rapide Réglages DU Menu RapideRéglages du verrouillage du mot de Passe MOT DE Passe Réglages DU MOT DE PasseNouveau MOT PASSE? Opération du contrôleur Réglage RaccourcisIris Fermer Problème EN CAS DE ProblèmesCause et action recommandée 88-89 87-88 Problème Vision Nuit OFF CAG Élevé Caractéristiques TechniquesOFF, SÉQ, TRI, Auto PAN, PATR, Suivi Auto CAG OUI BAS, OUI MOYEN, OUI ELEVE, OFFSÉQ, TRI, Auto PAN, PATR, Suivi Auto OUI/OFF103 Imprimé au Japon

WV-CS954 specifications

The Panasonic WV-CS954 is a sophisticated and versatile CCTV camera designed for high-performance surveillance applications. This model is equipped with advanced features that make it ideal for various environments, whether indoor or outdoor.

One of the standout characteristics of the WV-CS954 is its exceptional image quality. The camera utilizes a high-resolution 1/3-inch CCD sensor that delivers crisp and clear images with a resolution of 540 TV lines. This ensures that even the finest details are captured, enabling effective monitoring and identification of subjects in various lighting conditions.

The WV-CS954 is also equipped with a powerful 10x optical zoom lens, enabling users to zoom in on subjects without sacrificing image clarity. This feature is particularly useful in scenarios where details are crucial, such as monitoring entry points or observing large areas. The camera also incorporates a digital zoom capability, which further extends its versatility for surveillance needs.

In terms of technology, the WV-CS954 integrates advanced features such as auto focus and auto iris functions, enhancing its performance in fluctuating light conditions. These technologies help maintain optimal exposure and sharpness, ensuring reliable operation regardless of the environment.

Another notable feature of the WV-CS954 is its pan and tilt capability. The camera can be remotely controlled to pan 360 degrees and tilt up to 180 degrees, offering flexible coverage of expansive areas. This allows operators to monitor large spaces efficiently, making it an excellent choice for retail stores, parking lots, and other open environments.

The camera is also designed with durability in mind. Its robust construction and weather-resistant design make it suitable for outdoor use, capable of withstanding various environmental challenges. Additionally, the WV-CS954 is compatible with various mounting options, further enhancing its adaptability in different settings.

For connectivity, the WV-CS954 supports both analog and digital interface options, making it easy to integrate into existing security systems. It is also compatible with Panasonic's comprehensive suite of video management software, enabling seamless surveillance operations.

In conclusion, the Panasonic WV-CS954 is a reliable and feature-rich surveillance camera that offers exceptional image quality, flexible monitoring capabilities, and robust design. Its advanced technologies and user-friendly features make it a top choice for security professionals looking to enhance their surveillance solutions.
Top Page Image Contents