Panasonic WV-CS954 Auto PAN Key Setting Auto PAN KEY, Patrol Function Setting Patrol

manually, the auto mode function should be cancelled.

To activate the auto mode, select the desired auto mode again or set a time for SELF RETURN in the SET UP menu.

•When 0S is selected, the camera stops without dwelling and starts.

•Auto refreshing may be activated during the patrol play or the auto mode to calibrate the lens position.

(6)AUTO PAN Key Setting (AUTO PAN KEY)

Set the operations of the camera when AUTO PAN is executed from the system controller (page 31, 32).

1.Move the cursor to AUTO PAN KEY, and then tilt the joystick left or right to select a camera movement mode setting.

Tilting the joystick cycles through settings in the sequence shown below.

AUTO PAN ↔ SEQ ↔ SORT ↔ PATROL1 ↔ PATROL2

AUTO TRACK ↔ PATROL4 ↔ PATROL3

Note: Auto Mode can be started, but not stopped, with the AUTO PAN key.

(7) Patrol Function Setting (PATROL)

The patrol function remembers manual operations for later automatic playback when they are needed.

1.Aim the camera, with the menu closed, at the start point of the routine you want it to remember.

2.Move the cursor to NUMBER, and then tilt the joystick left or right to specify the number of patrol routines.

Tilting the joystick cycles through settings in the sequence shown below. The amount of storage time available depends on the number of routines. The storage time display changes in the sequence shown below. (unit: sec, min)

1(2MIN) ↔ 2(1MIN) ↔ 4(30S)

Note that the total patrol time is two minutes, and the time allowed for each routine depends on the number of patrol routines that are configured. The values in parentheses indicate the time of each patrol routine (two minutes for one pattern, one minute each for two patterns, 30 seconds each for four patterns).

**PATROL**

NUMBER	4(30S)
PATROL1*	PLAY
PATROL2	---
PATROL3	---
PATROL4	---

RESET

RET TOP

If you want to change the number of patrol routines from a previous setting, first delete all of the currently store patrol routines. To delete everything, move the cursor to RESET, and press the CAM (SET) button.

-32-

3.Move the cursor to a PATROL number (PATROL 1 through 4), and then tilt the joystick left or right to select a patrol setting.

---: Disables the selected patrol routine.

PLAY : Performs the selected patrol routine.

LEARN : Select this option to teach the camera a series of movements (patrol routine). (An asterisk (*) to the right of a PATROL number indicates that it already has a patrol routine assigned to it.)

DEL→PUSH SET : Press the CAM (SET) button to delete an existing patrol routine.

4.Turn off the menu display with the F2 button on the system controller, and activate the patrol function set in step 3.

Turning on the system controller's menu during a LEARN operation causes the LEARN operation to end. It also ends when the maximum storage time is exceeded. Activate PLAY to check the stored operations.

Notes:

•Selecting LEARN to teach the camera a patrol routine causes the following parameters to be stored along with the camera movements.

(1)Parameters at the Beginning of the Routine

•PAN, TILT, ZOOM, and FOCUS positions

•IRIS level

•Shutter speed (SHUTTER)

•Gain (AGC) setting

•Electronic sensitivity enhancement (SENS UP) setting

•White balance (WHITE BAL) setting

•IMAGE HOLD

•AREA TITLE

•DIGITAL FLIP

•PRIVACY ZONE

•CAMERA ID

•PROPO.PT

•PAN LIMIT

•ZOOM LIMIT

•TILT ANGLE

•BURST

•CLEANING

(2)During Camera Movement

•PAN, TILT, ZOOM, and FOCUS positions

•IRIS operation

•Preset positioning

•In the patrol play mode, the camera movement may occasionally deviate from the entered routine when the routine includes a move to a preset position. If this happens, re-enter the routine of manual operations for patrol-learn.

•In the patrol play mode, black and white automatic switching does not work.

•In the patrol play mode, when the power of the system controller is turned on or off, the patrol play stops. In this case, press the PATROL PLAY button again. (If SELF RETURN is set to ON, the patrol play will start again after elapsing the setting return time.)