Precor M9.35I manual Checking the Alignment and Adjusting the Running Belt

Page 83

Checking the Alignment and Adjusting the Running Belt

Proper belt alignment allows the belt to remain centered and ensures smooth operation. Realigning the belt takes a few simple adjustments. If you are unsure about this procedure, call Precor Customer Support. Refer to Obtaining Service.

To check the alignment:

1.The treadmill has adjustable rear feet. Make sure that the running surface is level before aligning or adjusting the running belt. Refer to step 17.

2.Turn the unit ON.

3.Stand beside the treadmill and press QUICKSTART.

4.If you are prompted for a password, press INCLINE ▼, SPEED ▼, SPEED ▲. The running belt starts automatically after the 3-second countdown appears on the display.

5.Press the SPEED ▲ key until the display shows a speed of 3 mph (5 kph).

6.Walk around to the rear of the unit and observe the belt for a few minutes. The belt should run centered along the running bed. If the belt drifts off center, you will need to make adjustments.

Important: If the belt needs alignment, make the adjustments immediately after turning the treadmill OFF. Failure to do so may cause the belt to tear or fray, which is not covered by the Precor Limited Warranty.

7.To stop the running belt, press the red STOP button.

8.Turn the treadmill OFF.

To adjust the running belt:

CAUTION: To ensure your safety, turn OFF (O) the treadmill before making any adjustments.

1.Locate the right belt adjustment bolt in the rear end cap of the treadmill. (To determine left and right, stand at the rear of the treadmill and face the display.) Make all belt adjustments on the right rear corner bolt using the ¼-inch hex key.

•If the belt is off center to the LEFT, turn the adjusting bolt ¼ turn counterclockwise, which moves the running belt to the right.

•If the belt tracks off center to the RIGHT, turn the bolt ¼ turn clockwise; this moves

the belt to the left.

Important: Do not turn the adjusting bolt more than ¼ turn at a time. Overtightening the bolt can damage the treadmill.

2. Recheck the alignment of the running belt.

M9.3xi Low-Impact Treadmills Assembly Guide

7

Image 83

Contents M9.33i M9.35i Page Important Safety Instructions Grounding Instructions Grounding Instructions Password SecuritySafety Approval Federal Communications Commission, Part Radio Frequency Interference RFIUnits Designated for U.S. Markets Débranchez avant de réparer European ApplicationsCanadian Department of Communications Obtaining Service Table of Contents Precor Residential Equipment Using the Safety Clip Treadmill Safety FeaturesTurning the Unit on and OFF Entering the PasswordUsing the Handrails Guidelines 120Heart Rate Target Zones High range 220 minus your age multiplied by 85%Using the Heart Rate Touch-Sensitive Grips Heart rate target zones and SmartRate LEDs Using SmartRateExercise to Your Target Heart Rate 2 a v e r a g e h e a r t r a t e Heart Rate AnalysisDisplay Console Stop Column 2 Distance and Incline More Information about the Lower DisplayColumn 1 TIME, Segment TIME, and Pace Column 4 CALORIES, CAL PER MIN, and Mets Column 3 Speed and Watts353i KeypadDiagram 7 Column height affected by changes in incline Quickstart User ID Keys Workout Options Choosing Quickstart 2530 Selecting a User IDYou have two options Selecting a Program Cooling Down After a Workout Pausing During a Workout or the Cool-Down Period Same PERS. Best Ending a WorkoutPrograms Program Tips Choosing a Program10K Program 5K ProgramCustom Programs Calories Goal ProgramClearing the Settings in a Custom Program I t n e s s t e s t Distance Goal ProgramFitness Test Program I s t a n c e g o a lFitness Test Scores Using the Fitness TestGuidelines Completing the Fitness TestCardio respiratory Fitness Score Category-Females A r t T e Heart Rate ProgramWarm-up Period R w e i g h t l o s s Using the Heart Rate ProgramHR Programs Heart Rate Program or the HR Weight N t e r v a l 1 Interval ProgramsL e Manual ProgramOne Mile Program N u a lN d o m Random ProgramRun Programs A c k Track ProgramTwo Mile Program A l k i n t h e p a r k Walk in the Park ProgramWalk Programs E i g h t l o s s Weight Loss ProgramAdvanced Programming Tips Advanced Programming and TroubleshootingChanging a User ID to a Name M9.35i Clearing User ID PreferencesSelecting a U.S. Standard or Metric Display Selecting Password Protection Viewing the Odometer Informational DisplaysViewing the Software Version and Part Numbers Viewing the Hour Meter12000 MI 1714 HrS Viewing the Error LogViewing the Serial Number Troubleshooting Error CodesErratic heart rate readings Troubleshooting Heart RateInspection Cleaning the EquipmentChecking the Alignment Running Belt Storing the Chest StrapAdjusting the Running Belt Servicing the Treadmill Long-Term Storage Options / Accessories Limited WarrantyWarranty Periods and Coverage Conditions and Restrictions This limited warranty shall not apply toExclusive Remedies Disclaimer and ReleaseExclusion of Consequential and Incidental Damages Thank You and Welcome to Precor Tell US about Your NEW Precor Product M9.3xi Low Impact Treadmills Product SpecificationsPage Quickstart Use the Safety ClipChoose a Program Assembly Guide Page Required Tools Hardware Kit not to scale Assembly Steps Incline , Speed , Speed Handrail clamp fasteners can damage the cable M9.3xi Low-Impact Treadmills Assembly Guide Checking the Alignment and Adjusting the Running Belt M9.3xi Low-Impact Treadmills Assembly Guide Page Precor Incorporated 20031 142nd Avenue NE Box