Alliance Laundry Systems PHM802N, PHM798N manual Machine Foundation Requirements

Page 26

Specifications and Dimensions

Machine Foundation Requirements

A 6 inch (153 mm) (for 35 and 60 2-speed, L-speed and M-speed models) or a 12 inch (305 mm) (for all other models) thickness of 3500 psi reinforced concrete foundation is absolutely necessary because of the high extract speed and the G-forces exerted.

When designing floors or foundations, refer to Table 3 for Floor Load Data for all model sizes. If the foundation requirements have been met, proceed to Mounting Bolt Installation Requirements section.

NOTE: Do not mount on wooden floors, above ground level, or over basements. Installation must be “slab on grade” or equal.

Thoroughness of detail must be stressed with all foundation work to ensure a stable unit installation, eliminating possibilities of excessive vibration during extract.

CAUTION

Ensure that the machine is installed on a floor that is level to within 3/8 inch when the machine is grouted. Also ensure that the floor is of sufficient strength and that the recommended clearances for inspection and maintenance are provided. Never allow the inspection and maintenance space to be blocked.

W760

WARNING

To reduce the risk of fire, this appliance must be bolted to an uncovered concrete floor.

W743

For new foundations a bolt-locator fixture or rebar frame is available and a preferred option. This rigid welded assembly made of reinforcing rod and mounting bolts is designed to be embedded in concrete. Refer to Figure 11.

The washer-extractor must be anchored to a smooth level surface so that the entire base of the machine is supported and rests on the mounting surface. (Do not support the washer-extractor on only four points.)

Make sure to grout machine. Refer to Figure 10 and Figure 11.

24

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F8138601

Image 26

Contents Washer-Extractors Page Contents Explanation of Safety Messages Important Safety InstructionsSafety Information Safety Decals Operator Safety Machine Location Safe Operating EnvironmentEnvironmental Conditions Input and Output Services AC Inverter DriveIntroduction Model IdentificationDelivery Inspection Replacement PartsCustomer Service Name plate Location0001 Model Number Familiarization Guide Models Starting 4/1/09Door Opening Information Weight And Shipping InformationWash Cylinder Information Drive Train InformationElectrical Heating Optional Balance DetectionDirect Steam Heating Optional Overall width, in. mm MED Crush hazard Machine DimensionsSpecifications and Dimensions Uwtv Models Through 3/31/09UW35TV UW125TV Models UW150TV Models Dimension 35 125 Models Models UW Design 3 Models starting 10/4/10 Refer to and Figure Base BA Base Overall PHM807N Machine Foundation Requirements Concrete Foundation Pad Installation Proceed to Machine Mounting and Grouting sectionLength for ONE Machine Floor Load Data 1272 1442 Speed 1745 2392 Speed 1797 2342 10.4 Mounting Bolt Installation Requirements Machine Mounting and Grouting Mounting Bolt Hole Locations Speed Models onlyVARIABLE-SPEED Model Front of Machine 80 / 100 Models 1181 mm 178 mm 254 mm Model Grout Placement 35 2-SPEED ModelGap Setting for Vibration Switch For UniLinc Models, Navigate to the Inputs Outputs MenuPound Model 60, 80, 100 and 125 Pound Models Design 1 150 Pound Model Drain Trough Configuration Drain Connection RequirementsDrain Information Specifications 100 125 150 Water Supply Information Specifications 80/100 125/150 Water ConnectionAir Cushions Risers Electrical Installation Requirements 50Hz ConversionDo not use a phase adder on any variable- speed machine Specifications and Dimensions Code CycleM30 Control Models only Steam Requirements Steam Heat Option Only Steam Supply Information 100 125/150Chemical Injection Supply System Connecting External Liquid Supplies to the Washer-Extractor Chemical Injection Supply SystemPHM553N External Supplies Chemical Injection Using Internal 24VAC Control Transformer Chemical injection Using External AC Power Source External Supply Signals ES1 Power supply Supply 1 Signal K1 Contact