Alliance Laundry Systems PHM802N, PHM798N Electrical Installation Requirements, 50Hz Conversion

Page 48

Specifications and Dimensions

Electrical Installation Requirements

IMPORTANT: Electrical ratings are subject to change. Refer to serial decal for electrical ratings information specific to your machine.

WARNING

This machine must be installed, adjusted, and serviced by qualified electrical maintenance personnel familiar with the construction and operation of this type of machinery. They must also be familiar with the potential hazards involved. Failure to observe this warning may result in personal injury and/or equipment damage, and may void the warranty.

SW004

WARNING

Dangerous voltages are present in the electrical control box(es) and at the motor terminals. Only qualified personnel familiar with electrical test procedures, test equipment, and safety precautions should attempt adjustments and troubleshooting. Disconnect power from the machine and wait 3 minutes before removing the control box cover, and before attempting any service procedures.

W702

WARNING

Ensure that a ground wire from a proven earth ground is connected to the ground lug near the input power block on this machine. Without proper grounding, personal injury from electric shock could occur and machine malfunctions may be evident.

SW008

Electrical connections are made at the rear of the machine. The machine must be connected to the proper electrical supply shown on the identification plate attached to the rear of the machine, using copper conductors only.

IMPORTANT: Alliance Laundry Systems warranty does not cover components that fail as a result of improper input voltage.

Make sure the correct transformer jumper (208 Volt or 240 Volt) is in place. Refer to the “optional” Electrical Service Connection label located on the back of the machine near the electrical service input for machine electrical requirements. Refer to Figure 24.

OPTIONAL ELECTRICAL SERVICE

200-208 VAC CONVERSION

F8099701R1

50Hz CONVERSION

 

CONNECTION BASED ON

VAC: 200-208

WIRES & GROUND: *

 

* As indicated on

1. Refer to the Control Option Diagram.

AVAILABILITY

PHASE: *

REC'D BREAKER: *

 

original serial plate

2. Remove the wire from the 60Hz tap on drain

AMPS: *

 

 

 

 

valve(s).

 

 

 

This unit may be field converted 1. Refer to the Control Transformer area on

 

 

 

3. Connect the wire to the 50Hz Tap on all

Transformer Jumper

drain valves.

 

 

 

by a QUALIFIED Electrician to

the Control Option Diagram.

 

 

 

2. Remove the "240V" Transformer Jumper in

 

 

208V

4. Sign off below.

Connection Drain Valve(s)

the following 200-208 Volts

 

 

 

 

for 50Hz

 

the control box.

 

 

 

 

 

 

Operation Only

50Hz

and/or 50 Hertz.

 

 

 

 

 

 

 

3. Replace with "208V" Transformer Jumper

 

 

 

 

 

 

60Hz N

 

found in the diagram pack.

 

 

 

 

 

 

PRIOR TO CONNECTING

 

 

 

 

 

 

 

4. Sign off below.

 

 

 

 

 

 

 

 

ELECTRICAL SERVICE,

200-208VAC

 

 

on

 

50Hz

 

on

 

COMPLETE THE FOLLOWING

 

 

 

(SIGN)

 

Operation

(SIGN)

 

 

(DATE)

Operation

 

(DATE)

O, Q, X AND Y – VOLTAGE MODELS

PHM740N

N, P AND R – VOLTAGE MODELS

PHM756N

 

Figure 24

On variable-speed models, the AC inverter drive requires a clean power supply free from voltage spikes and surges. A voltage monitor should be used to check incoming power. The customer’s local power company may provide such a monitor.

The following conditions require corrective action, contact the local utility to adjust the voltage. If the local utility cannot adjust the input voltage, install a buckboost transformer to lower the input voltage. Input voltage is above 240V or 480V, phase to ground voltage exceeds 125% of normal line to line voltage, or 240V open delta configuration (stinger leg). Contact the distributor or the manufacturer for assistance.

46

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F8138601

Image 48
Contents Washer-Extractors Page Contents Explanation of Safety Messages Important Safety InstructionsSafety Information Safety Decals Operator Safety Safe Operating Environment Environmental ConditionsMachine Location Input and Output Services AC Inverter DriveIntroduction Model IdentificationReplacement Parts Customer ServiceDelivery Inspection Name plate Location0001 Model Number Familiarization Guide Models Starting 4/1/09Weight And Shipping Information Wash Cylinder InformationDoor Opening Information Drive Train InformationBalance Detection Direct Steam Heating OptionalElectrical Heating Optional Overall width, in. mm MED Machine Dimensions Specifications and DimensionsCrush hazard Uwtv Models Through 3/31/09UW35TV UW125TV Models UW150TV Models Dimension 35 125 Models Models UW Design 3 Models starting 10/4/10 Refer to and Figure Base BA Base Overall PHM807N Machine Foundation Requirements Concrete Foundation Pad Installation Proceed to Machine Mounting and Grouting sectionLength for ONE Machine Floor Load Data 1272 1442 Speed 1745 2392 Speed 1797 2342 10.4 Mounting Bolt Installation Requirements Machine Mounting and Grouting Mounting Bolt Hole Locations Speed Models onlyVARIABLE-SPEED Model Front of Machine 80 / 100 Models 1181 mm 178 mm 254 mm Model Grout Placement 35 2-SPEED ModelGap Setting for Vibration Switch For UniLinc Models, Navigate to the Inputs Outputs MenuPound Model 60, 80, 100 and 125 Pound Models Design 1 150 Pound Model Drain Trough Configuration Drain Connection RequirementsDrain Information Specifications 100 125 150 Water Supply Information Specifications 80/100 125/150 Water ConnectionAir Cushions Risers Electrical Installation Requirements 50Hz ConversionDo not use a phase adder on any variable- speed machine Specifications and Dimensions Code CycleM30 Control Models only Steam Requirements Steam Heat Option Only Steam Supply Information 100 125/150Chemical Injection Supply System Connecting External Liquid Supplies to the Washer-Extractor Chemical Injection Supply SystemPHM553N External Supplies Chemical Injection Using Internal 24VAC Control Transformer Chemical injection Using External AC Power Source External Supply Signals ES1 Power supply Supply 1 Signal K1 Contact