Alliance Laundry Systems PHM802N, PHM798N manual Introduction, Model Identification

Page 10

Introduction

Model Identification

Information in this manual is applicable to these models:

UW35TV	UWL060K1L	UWN035K1L	UWN100K1M	UWU060K1L

UW60TV	UWL060K1M	UWN035K1M	UWN100T3V	UWU060K1M

UW80TV	UWL060T3L	UWN035T3L	UWN125K1M	UWU060T3L

UW100TV	UWL060T3M	UWN035T3M	UWN125K1V	UWU060T3M

UW125TV	UWL060T3V	UWN035T3V	UWN125T3V	UWU060T3V

UW150TV	UWL080K1M	UWN060K12	UWN150T3V	UWU080K1M

UWL035K12	UWL080T3V	UWN060K1L	UWU035K12	UWU080T3V

UWL035K1L	UWL100K1M	UWN060K1M	UWU035K1L	UWU100K1M

UWL035K1M	UWL100T3V	UWN060T3L	UWU035K1M	UWU100T3V

UWL035T3L	UWL125K1M	UWN060T3M	UWU035T3L	UWU125K1M

UWL035T3M	UWL125T3V	UWN060T3V	UWU035T3M	UWU125T3V

UWL035T3V	UWL150T3V	UWN080K1M	UWU035T3V	UWU150T3V

UWL060K12	UWN035K12	UWN080T3V	UWU060K12

8

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F8138601

Image 10

Contents Washer-Extractors Page Contents Explanation of Safety Messages Important Safety InstructionsSafety Information Safety Decals Operator Safety Environmental Conditions Safe Operating EnvironmentMachine Location Input and Output Services AC Inverter DriveIntroduction Model IdentificationDelivery Inspection Replacement PartsCustomer Service Name plate Location0001 Model Number Familiarization Guide Models Starting 4/1/09Door Opening Information Weight And Shipping InformationWash Cylinder Information Drive Train InformationDirect Steam Heating Optional Balance DetectionElectrical Heating Optional Overall width, in. mm MED Crush hazard Machine DimensionsSpecifications and Dimensions Uwtv Models Through 3/31/09UW35TV UW125TV Models UW150TV Models Dimension 35 125 Models Models UW Design 3 Models starting 10/4/10 Refer to and Figure Base BA Base Overall PHM807N Machine Foundation Requirements Concrete Foundation Pad Installation Proceed to Machine Mounting and Grouting sectionLength for ONE Machine Floor Load Data 1272 1442 Speed 1745 2392 Speed 1797 2342 10.4 Mounting Bolt Installation Requirements Machine Mounting and Grouting Mounting Bolt Hole Locations Speed Models onlyVARIABLE-SPEED Model Front of Machine 80 / 100 Models 1181 mm 178 mm 254 mm Model Grout Placement 35 2-SPEED ModelGap Setting for Vibration Switch For UniLinc Models, Navigate to the Inputs Outputs MenuPound Model 60, 80, 100 and 125 Pound Models Design 1 150 Pound Model Drain Trough Configuration Drain Connection RequirementsDrain Information Specifications 100 125 150 Water Supply Information Specifications 80/100 125/150 Water ConnectionAir Cushions Risers Electrical Installation Requirements 50Hz ConversionDo not use a phase adder on any variable- speed machine Specifications and Dimensions Code CycleM30 Control Models only Steam Requirements Steam Heat Option Only Steam Supply Information 100 125/150Chemical Injection Supply System Connecting External Liquid Supplies to the Washer-Extractor Chemical Injection Supply SystemPHM553N External Supplies Chemical Injection Using Internal 24VAC Control Transformer Chemical injection Using External AC Power Source External Supply Signals ES1 Power supply Supply 1 Signal K1 Contact