Alliance Laundry Systems PHM798N, PHM802N manual Contents

Page 3

Table of

Contents

Safety Information	2
Explanation of Safety Messages	2
Important Safety Instructions	2
Safety Decals	4
Operator Safety	5
Safe Operating Environment	6
Environmental Conditions	6
Machine Location	6
Input and Output Services	7
AC Inverter Drive	7
Introduction	8
Model Identification	8
Delivery Inspection	9
Name plate Location	9
Nameplate Location - UniLinc Models	9
Replacement Parts	9
Customer Service	9
Specifications and Dimensions	11
Machine Dimensions	15
UWTV Models Through 3/31/09	15
UW Design 1 and Design 2 Models
Starting 4/1/09 Through 10/3/10	18
UW Design 3 Models starting 10/4/10	21
Machine Foundation Requirements	24
Concrete Foundation Pad Installation	25
Floor Load Data	27
Mounting Bolt Installation Requirements	30
Machine Mounting and Grouting	31
Mounting Bolt Hole Locations	32
Grout Placement	37
Gap Setting for Vibration Switch	38
Drain Connection Requirements	42
Water Connection	44
Electrical Installation Requirements	46
Steam Requirements (Steam Heat Option Only)	51
Chemical Injection Supply System	52
External Supplies	55
Chemical Injection Using Internal 24VAC Control Transformer ...	56
Chemical injection Using External AC Power Source	57
External Supply Signals	58

© Copyright 2011, Alliance Laundry Systems LLC

All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher.

F8138601

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

1

Image 3

Contents Washer-Extractors Page Contents Important Safety Instructions Explanation of Safety MessagesSafety Information Safety Decals Operator Safety Safe Operating Environment Environmental ConditionsMachine Location AC Inverter Drive Input and Output ServicesModel Identification IntroductionName plate Location Replacement PartsCustomer Service Delivery InspectionModel Number Familiarization Guide Models Starting 4/1/09 0001Drive Train Information Weight And Shipping InformationWash Cylinder Information Door Opening InformationBalance Detection Direct Steam Heating OptionalElectrical Heating Optional Overall width, in. mm MED Uwtv Models Through 3/31/09 Machine DimensionsSpecifications and Dimensions Crush hazardUW35TV UW125TV Models UW150TV Models Dimension 35 125 Models Models UW Design 3 Models starting 10/4/10 Refer to and Figure Base BA Base Overall PHM807N Machine Foundation Requirements Proceed to Machine Mounting and Grouting section Concrete Foundation Pad InstallationLength for ONE Machine Floor Load Data 1272 1442 Speed 1745 2392 Speed 1797 2342 10.4 Mounting Bolt Installation Requirements Machine Mounting and Grouting Speed Models only Mounting Bolt Hole LocationsVARIABLE-SPEED Model Front of Machine 80 / 100 Models 1181 mm 178 mm 254 mm Model 35 2-SPEED Model Grout PlacementFor UniLinc Models, Navigate to the Inputs Outputs Menu Gap Setting for Vibration SwitchPound Model 60, 80, 100 and 125 Pound Models Design 1 150 Pound Model Drain Connection Requirements Drain Trough ConfigurationDrain Information Specifications 100 125 150 Water Connection Water Supply Information Specifications 80/100 125/150Air Cushions Risers 50Hz Conversion Electrical Installation RequirementsDo not use a phase adder on any variable- speed machine Specifications and Dimensions Cycle CodeM30 Control Models only Steam Supply Information 100 125/150 Steam Requirements Steam Heat Option OnlyChemical Injection Supply System Chemical Injection Supply System Connecting External Liquid Supplies to the Washer-ExtractorPHM553N External Supplies Chemical Injection Using Internal 24VAC Control Transformer Chemical injection Using External AC Power Source External Supply Signals ES1 Power supply Supply 1 Signal K1 Contact