Alliance Laundry Systems PHM798N, PHM802N UW Design 3 Models starting 10/4/10 Refer to and Figure

Page 23

Specifications and Dimensions

UW Design 3 Models starting 10/4/10

(Refer to Figure 7 and Figure 8)

	Dimension	35		60		80		100		125			150

		in.	mm	in.	mm	in.	mm	in.	mm	in.	mm	in.	mm
		in.	mm	in.	mm	in.	mm	in.	mm	in.	mm	in.	mm

	A	30.125	765	35.625	905	41.125	1045	41.125	1045	48	1219	50	1270

	B	32.37	822	36.07	916	41.06	1043	41.06	1043	47.91	1217	50.23	1276

	C	23.41	595	28.07	713	29.29	744	29.29	744	28.5	723	31.41	798

	D	45.27	1150	46.81	1189	50	1270	56.03	1423	55.04	1398	62	1575

	E	54.32	1380	64.40	1636	67.75	1721	67.75	1721	72.18	1833	78.77	2001

	F1	36.18	919	38.87	987	45.56	1157	48.08	12.21	48.25	1226	56.26	1429
	G	6.79	172	14.73	374	15.94	405	15.94	405	11.71	297	15.69	399

	H	47.06	1195	53.71	1364	56.42	1433	56.42	1433	57.92	1471	64.36	1635

	J	2.3	58	2.3	58	2.3	58	2.3	58	2.3	58	2.3	58

	K	4.9	124	4.9	124	4.9	124	4.9	124	4.9	124	4.9	124

	L	7.8	198	7.8	198	7.8	198	7.8	198	7.8	198	7.8	198

	M	10.4	264	10.4	264	10.4	264	10.4	264	10.4	264	10.4	264

	N	2.6	66	2.6	66	2.6	66	2.6	66	2.6	66	2.6	66

	O	2.85	72	2.85	72	2.85	72	2.85	72	2.85	72	2.85	72

1The overhang dimension for the premium wet clean module option (compatible with wet-clean-capable washer-extractors only) adds 24 inches (60.96 cm) to combined machine dimensions E and G.

Table 3

F8138601

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

21

Image 23

Contents Washer-Extractors Page Contents Important Safety Instructions Explanation of Safety MessagesSafety Information Safety Decals Operator Safety Machine Location Safe Operating EnvironmentEnvironmental Conditions AC Inverter Drive Input and Output ServicesModel Identification IntroductionName plate Location Replacement PartsCustomer Service Delivery InspectionModel Number Familiarization Guide Models Starting 4/1/09 0001Drive Train Information Weight And Shipping InformationWash Cylinder Information Door Opening InformationElectrical Heating Optional Balance DetectionDirect Steam Heating Optional Overall width, in. mm MED Uwtv Models Through 3/31/09 Machine DimensionsSpecifications and Dimensions Crush hazardUW35TV UW125TV Models UW150TV Models Dimension 35 125 Models Models UW Design 3 Models starting 10/4/10 Refer to and Figure Base BA Base Overall PHM807N Machine Foundation Requirements Proceed to Machine Mounting and Grouting section Concrete Foundation Pad InstallationLength for ONE Machine Floor Load Data 1272 1442 Speed 1745 2392 Speed 1797 2342 10.4 Mounting Bolt Installation Requirements Machine Mounting and Grouting Speed Models only Mounting Bolt Hole LocationsVARIABLE-SPEED Model Front of Machine 80 / 100 Models 1181 mm 178 mm 254 mm Model 35 2-SPEED Model Grout PlacementFor UniLinc Models, Navigate to the Inputs Outputs Menu Gap Setting for Vibration SwitchPound Model 60, 80, 100 and 125 Pound Models Design 1 150 Pound Model Drain Connection Requirements Drain Trough ConfigurationDrain Information Specifications 100 125 150 Water Connection Water Supply Information Specifications 80/100 125/150Air Cushions Risers 50Hz Conversion Electrical Installation RequirementsDo not use a phase adder on any variable- speed machine Specifications and Dimensions Cycle CodeM30 Control Models only Steam Supply Information 100 125/150 Steam Requirements Steam Heat Option OnlyChemical Injection Supply System Chemical Injection Supply System Connecting External Liquid Supplies to the Washer-ExtractorPHM553N External Supplies Chemical Injection Using Internal 24VAC Control Transformer Chemical injection Using External AC Power Source External Supply Signals ES1 Power supply Supply 1 Signal K1 Contact