Alliance Laundry Systems PHM798N Delivery Inspection, Name plate Location, Replacement Parts

Page 11

This manual is designed as a guide to the installation of the Pocket Hardmount washer-extractor.

NOTE: All information, illustrations, and specifications contained in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.

IMPORTANT: Warranty is void unless washer- extractor is installed according to instructions in this manual. Installation should comply with minimum specifications and requirements, and with applicable municipal building codes, water supply regulations, electrical wiring regulations and any other relevant statuary regulations. Due to varied requirements, applicable local codes should be thoroughly understood and all pre-installation work arranged for accordingly.

Delivery Inspection

Upon delivery, visually inspect crate, protective cover, and unit for any visible shipping damage. If the crate, protective cover, or unit is damaged or signs of possible damage are evident, have the carrier note the condition on the shipping papers before the shipping receipt is signed, or advise the carrier of the condition as soon as it is discovered.

Remove the crate and protective cover as soon after delivery as possible. If any damage is discovered upon removal of the crate and/or protective cover, advise the carrier and file a written claim immediately.

Name plate Location

The nameplate is located on the back of the machine. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. Refer to Figure 1 and Figure 2.

Nameplate Location - UniLinc Models

On UniLinc models, nameplate information is also programmed into the control. To access machine ID through the control:

1.Press and hold , then , then keypads at the same time.

2.Press the keypad until Diagnostic is highlighted.

3.Press the keypad.

4.Press the keypad until machine ID is highlighted.

Introduction

5. Press the keypad.

Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. Refer to Figure 1.

MODEL EXAMPLE OF NAMEPLATE LOCATION

1

2

 

PHM798N

1In Control (UniLinc Models)

2At Back of Machine

Figure 1

Replacement Parts

If literature or replacement parts are required, contact the source from which the washer-extractor was purchased or contact Alliance Laundry Systems LLC at (920) 748-3950 for the name of the nearest authorized parts distributor. A parts manual may be ordered by returning the reply card provided with each washer-extractor.

Customer Service

For technical assistance, contact your local distributor or call:

(920)748-3121 Ripon, Wisconsin

A record of each washer-extractor is on file with the manufacturer. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. Refer to Figure 1 and Figure 2.

F8138601

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Washer-Extractors Page Contents Important Safety Instructions Explanation of Safety MessagesSafety Information Safety Decals Operator Safety Machine Location Safe Operating EnvironmentEnvironmental Conditions AC Inverter Drive Input and Output ServicesModel Identification IntroductionName plate Location Replacement PartsCustomer Service Delivery InspectionModel Number Familiarization Guide Models Starting 4/1/09 0001Drive Train Information Weight And Shipping InformationWash Cylinder Information Door Opening InformationElectrical Heating Optional Balance DetectionDirect Steam Heating Optional Overall width, in. mm MED Uwtv Models Through 3/31/09 Machine DimensionsSpecifications and Dimensions Crush hazardUW35TV UW125TV Models UW150TV Models Dimension 35 125 Models Models UW Design 3 Models starting 10/4/10 Refer to and Figure Base BA Base Overall PHM807N Machine Foundation Requirements Proceed to Machine Mounting and Grouting section Concrete Foundation Pad InstallationLength for ONE Machine Floor Load Data 1272 1442 Speed 1745 2392 Speed 1797 2342 10.4 Mounting Bolt Installation Requirements Machine Mounting and Grouting Speed Models only Mounting Bolt Hole LocationsVARIABLE-SPEED Model Front of Machine 80 / 100 Models 1181 mm 178 mm 254 mm Model 35 2-SPEED Model Grout PlacementFor UniLinc Models, Navigate to the Inputs Outputs Menu Gap Setting for Vibration SwitchPound Model 60, 80, 100 and 125 Pound Models Design 1 150 Pound Model Drain Connection Requirements Drain Trough ConfigurationDrain Information Specifications 100 125 150 Water Connection Water Supply Information Specifications 80/100 125/150Air Cushions Risers 50Hz Conversion Electrical Installation RequirementsDo not use a phase adder on any variable- speed machine Specifications and Dimensions Cycle CodeM30 Control Models only Steam Supply Information 100 125/150 Steam Requirements Steam Heat Option OnlyChemical Injection Supply System Chemical Injection Supply System Connecting External Liquid Supplies to the Washer-ExtractorPHM553N External Supplies Chemical Injection Using Internal 24VAC Control Transformer Chemical injection Using External AC Power Source External Supply Signals ES1 Power supply Supply 1 Signal K1 Contact
Top Page Image Contents