Programming Control
What Can Be Programmed?
This feature allows the owner to program cycle information and other features by using the keypads. The control must have the Manual Programming Mode enabled, which is the factory default. This mode can only be turned “OFF” and “ON” by using an external device. Refer to this section when programming the control.
This section offers a detailed description of all available programmable options.
Each description includes instructions on when and why the option might be used and, more importantly, how to program the option.
For more advanced users, a quick reference list (refer to Table 1) of the options available through the programming mode is available. Programming flowcharts (refer to Figures Figure
NOTE: The letters and numbers in the Option Display column of the Programmable Options List are what will be shown in the display when that option is selected.
Programmable Options Available
Option | Option | Description | Default | Value Range |
Number | Display |
| Value |
|
1 | “dCYC” | Default Cycle | “Cy05”* | |
|
|
|
|
|
2 | “AUd” | Audio Signal | “29”* | |
|
|
|
|
|
3 |
| Errors | — | — |
|
|
|
|
|
a. | “E FL” | Fill Errors | “on” | “on”/“oFF” |
|
|
|
|
|
b. | “E dr” | Drain Error | “on” | “on”/“oFF” |
|
|
|
|
|
c. | “E Ub” | Unbalance Error Display | “on” | “on”/“oFF” |
|
|
|
|
|
d. | “E oP” | Open Thermister Error Display | “on” | “on”/“oFF” |
|
|
|
|
|
e. | “E SH” | Shorted Thermistor Error Display | “on” | “on”/“oFF” |
|
|
|
|
|
f. | “E Ht” | Heat Error Display (Heater only) | “on” | “on”/“oFF” |
|
|
|
|
|
g. | Water Leak Detection Error | — | — | |
|
|
|
|
|
1. | “LEr1” | 1. Water Leak Detection During a Machine Cycle | “oFF” | “on”/“oFF” |
|
| (On/Off) |
|
|
|
|
|
|
|
2. | “LEr2” | 2. Water Leak Detection Day of Week Enable | “127”* | |
|
|
|
|
|
3. | “LEr3”*** | 3. Number of Cycles Between Water Leak | “0” | |
|
| Detection During a Machine Cycle |
|
|
|
|
|
|
|
h. | “E Sd” | Slow Drain Detection | “oFF” | “on”/“oFF” |
|
|
|
|
|
4 | Cycle Programming | Refer to Operation Manual for default cycle | ||
|
|
|
| information |
|
|
|
|
|
a. | “AgIt” | Cycle Agitate | — | — |
|
|
|
|
|
1. | “tyPE” | Agitate Type | ** | |
|
|
|
|
|
2. | “ASPd” | Agitate Speed (VFD only) | ** | “Lo”/“rEg”* |
|
|
|
|
|
b. | “Segx” | Cycle Segment Programming | — | — |
|
|
|
| |
|
|
|
|
|
1. | “SgEn” | Segment Enable/Disable | ** | “on”/“oFF” |
|
|
|
|
|
Table 1 (continued)
F8208801 | © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT | 11 |