Alliance Laundry Systems PHM1263R Cold Water Temperature FC, Cooldown Enable/Temperature Codn

Page 35

10. Cold Water Temperature “FC”

This option allows the owner to program the cold water temperature for models equipped with temperature sensing capabilities.

How to Program Cold Water Temperature

1.Control must be in Manual Mode. Refer to Entering the Manual Mode.

2.Press the #3 (>) or the #6 (<) keypad until

Prog” appears in the display. Press the START (enter) keypad and “dCYC” will appear in the display.

3.Press the #3 (>) or the #6 (<) keypad to scroll through the programmable options until “FC” appears in the display.

4.When “FC” appears in the display, press the START (enter) keypad. A number will appear in the display. This number corresponds to the current Cold Water Temperature value.

5.Press the #3 (>) or the #6 (<) keypad to increase or decrease the current Cold Water Temperature value to the desired Cold Water Temperature value.

NOTE: Cold Water Temperature is selectable between 35° and 194° Fahrenheit (2° and 90° Celsius). Default temperature value is 35° Fahrenheit (2° Celsius).

NOTE: Refer to option 7 to select Celsius or Fahrenheit display.

6.Press the START (enter) keypad when the correct number appears in the display. The next option, “Codn”, will appear in the display.

NOTE: To program “Codn” (Cooldown Enable/ Temperature), refer to option 11. To program other options, refer to the appropriate section.

How to Exit Programming Feature

Press the #5 (<) keypad until the control returns to Start Mode.

Programming Control

11.Cooldown Enable/Temperature “Codn”

This option allows the owner to enable or disable the Cooldown Water Temperature option. If enabled, the owner can also set the cooldown water temperature.

How to Program Cooldown Enable/ Temperature

1.Control must be in Manual Mode. Refer to Entering the Manual Mode.

2.Press the #3 (>) or the #6 (<) keypad until

Prog” appears in the display. Press the START (enter) keypad and “dCYC” will appear in the display.

3.Press the #3 (>) or the #6 (<) keypad to scroll through the programmable options until “Codn” appears in the display.

4.When “Codn” appears in the display, press the START (enter) keypad. A number or “off” will appear in the display. The number corresponds to the current Cooldown Water Temperature value, and “oFF” appears when cooldown is disabled.

5.Press the #3 (>) or the #6 (<) keypad to change the current status.

NOTE: Cooldown Water Temperature is selectable between 50° and 160° Fahrenheit (10° and 71° Celsius). Default is off.

6.Press the START (enter) keypad when the desired value appears in the display.

NOTE: Refer to option 7 to select Celsius or Fahrenheit display.

7.Press the START (enter) keypad when the correct number appears in the display. The next option, “PtEn”, will appear in the display.

NOTE: To program “PtEn” (Production Test Cycle [on/off]), refer to option 12. To program other options, refer to the appropriate section.

How to Exit Programming Feature

Press the #5 (<) keypad until the control returns to Start Mode.

F8208801

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

33

Image 35
Contents Washer-Extractor Page W030 Contents Temperature Controlled Fill Enable/Disable tCF Model Identification Glossary of Terms Power Failure RecoveryPreliminary Information About the ControlSelect Cycle Pads Refer to Figure Control IdentificationFour 7-Segment Digits Display IdentificationLight Emitting Diodes LEDs Refer to Figure Washer-Extractor Operation Special Features Manual Programming Entering the Manual ModeHow to Enter the Manual Mode Manual DiagnosticsProgrammable Options Available Option Description Default Value Range Number DisplayProgramming Control What Can Be Programmed?SUEn FLEnTEnP CoLd/Uarn/HotorProgramming Control Manual Mode Flowchart Manual Programming Flowchart 1 Manual Programming Flowchart 2 Option available on software version 2 only Manual Programming Flowchart 3Diagnostic Tests Flowchart How to Exit Programming Feature Default Cycle dCYCHow to Program Default Cycle How to Program the Audio Signal Audio Signal AUdNot Cycle Pressed Used How to Read TableMode Card End Key Input Remove CoinESd Error Code Programming ErrHow to Program Error Code Programming LEr3SAT FRI Thur WED TUE MON SUN SAT FRI Thur WED TUE MON SUN OFF Final Description Status How to Enter Cycle ProgrammingHow to Program Cycle Agitate AgIt Cycle Programming CyFill Step Description Status How to Program Cycle Segment SEg1Agitate Description Status/Value Step SupplyDescription Status/Value StepExtract Description Programming Drain StepProgramming Cycle Time Display How to Program Number of Balance RetriesFahrenheit/Celsius t FC IR Access On/Off IrAHow to Program the IR Access On/Off How to Program Fahrenheit/CelsiusHow to Program Warm Water Temperature Hot Water Temperature FHWarm Water Temperature FHC How to Program Hot Water TemperatureHow to Program Cooldown Enable/ Temperature Cold Water Temperature FCCooldown Enable/Temperature Codn How to Program Cold Water TemperatureManual Rapid Advance On/Off rAEn How to Program the Production Test Cycle On/OffHow to Program the Manual Rapid Advance On/Off Production Test Cycle On/Off PtEnProgrammable Cycle Time Display PCtd How to Program in the Cycle Time DisplayHow to Program the Programmable Cycle Time Display No Cycle Time Display nCtdHow to Program the Pause/Resume Mode Slow Drain Detection Adjust SdAdSet Real-Time Clock rtC-’ How to Program the Time and DateLow Water Level FLo Manual Diagnostics On/Off dAEnHow to Program the Manual Diagnostics On/Off How to Program Low Water LevelHigh Water Level FHI How to Program Medium Water LevelHow to Program High Water Level Medium Water Level FnEdHow to Program Temperature Controlled Fill Temperature Controlled Fill Enable/Disable tCFAuto-Water Leak Detection ALd How to Program Auto-Water Leak DetectionCollecting Audit Information How to Enter Audit FeatureHow to Read Audit Data How to Exit Audit FeatureHow to Enter Manual Reset Manual ResetHow to Exit Testing Feature Testing Machine Electronic Control FunctionsHow to Enter Testing Feature How to Start TestsTxxx D001D002 D003Diagnostic Test Descriptions Frame Balance Switch Input Test Temperature Sensor Display TestVAC Switch Input Test VFD Drive Fault Input TestProduction Test Cycle Display Test Cycle Step Comments Production Test Cycle Quick Reference ChartDrAI then LoAg thenAg then RAg thenError Codes Door Error CodesHow to Exit Rapid Advance Feature Rapid Advance FeatureHow to Use Rapid Advance Infra-red Communications Communications ModeHow to Begin Communications with An External Device Default Cycles Default Cycles Cycle Stops Reclaim Delicates 90C 60C 40C 90C Perm 60C Perm Cycle reference CY08 CY09 Cycle Stops 40C Perm 70C Perm 50C Gentle 30C Gentle Blank CY17 CY18