Alliance Laundry Systems PHM1263R manual Off

Page 27

Programming Control

Table 4 (continued)

Day(s) of the Week Enabled Values

	Day Of Week	SAT	FRI	THUR	WED	TUE	MON	SUN
	Value	SAT	FRI	THUR	WED	TUE	MON	SUN
	Value
	84	ON	OFF	ON	OFF	ON	OFF	OFF
	85	ON	OFF	ON	OFF	ON	OFF	ON
	86	ON	OFF	ON	OFF	ON	ON	OFF
	87	ON	OFF	ON	OFF	ON	ON	ON
	88	ON	OFF	ON	ON	OFF	OFF	OFF
	89	ON	OFF	ON	ON	OFF	OFF	ON
	90	ON	OFF	ON	ON	OFF	ON	OFF
	91	ON	OFF	ON	ON	OFF	ON	ON
	92	ON	OFF	ON	ON	ON	OFF	OFF
	93	ON	OFF	ON	ON	ON	OFF	ON
	94	ON	OFF	ON	ON	ON	ON	OFF
	95	ON	OFF	ON	ON	ON	ON	ON
	96	ON	ON	OFF	OFF	OFF	OFF	OFF
	97	ON	ON	OFF	OFF	OFF	OFF	ON
	98	ON	ON	OFF	OFF	OFF	ON	OFF
	99	ON	ON	OFF	OFF	OFF	ON	ON
	100	ON	ON	OFF	OFF	ON	OFF	OFF
	101	ON	ON	OFF	OFF	ON	OFF	ON
	102	ON	ON	OFF	OFF	ON	ON	OFF
	103	ON	ON	OFF	OFF	ON	ON	ON
	104	ON	ON	OFF	ON	OFF	OFF	OFF
	105	ON	ON	OFF	ON	OFF	OFF	ON
	106	ON	ON	OFF	ON	OFF	ON	OFF
	107	ON	ON	OFF	ON	OFF	ON	ON
	108	ON	ON	OFF	ON	ON	OFF	OFF
	109	ON	ON	OFF	ON	ON	OFF	ON
	110	ON	ON	OFF	ON	ON	ON	OFF
	111	ON	ON	OFF	ON	ON	ON	ON
	112	ON	ON	ON	OFF	OFF	OFF	OFF
	113	ON	ON	ON	OFF	OFF	OFF	ON
	114	ON	ON	ON	OFF	OFF	ON	OFF
	115	ON	ON	ON	OFF	OFF	ON	ON
	116	ON	ON	ON	OFF	ON	OFF	OFF
	117	ON	ON	ON	OFF	ON	OFF	ON
	118	ON	ON	ON	OFF	ON	ON	OFF
	119	ON	ON	ON	OFF	ON	ON	ON
	120	ON	ON	ON	ON	OFF	OFF	OFF
	121	ON	ON	ON	ON	OFF	OFF	ON
	122	ON	ON	ON	ON	OFF	ON	OFF
	123	ON	ON	ON	ON	OFF	ON	ON
	124	ON	ON	ON	ON	ON	OFF	OFF
	125	ON	ON	ON	ON	ON	OFF	ON
	126	ON	ON	ON	ON	ON	ON	OFF
	127	ON	ON	ON	ON	ON	ON	ON

Table 4

F8208801

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

25

Image 27

Contents Washer-Extractor Page W030 Contents Temperature Controlled Fill Enable/Disable tCF Model Identification Glossary of Terms Power Failure RecoveryPreliminary Information About the ControlSelect Cycle Pads Refer to Figure Control IdentificationDisplay Identification Light Emitting Diodes LEDs Refer to FigureFour 7-Segment Digits Washer-Extractor Operation Special Features Manual Programming Entering the Manual ModeHow to Enter the Manual Mode Manual DiagnosticsProgrammable Options Available Option Description Default Value Range Number DisplayProgramming Control What Can Be Programmed?SUEn FLEnTEnP CoLd/Uarn/HotorProgramming Control Manual Mode Flowchart Manual Programming Flowchart 1 Manual Programming Flowchart 2 Option available on software version 2 only Manual Programming Flowchart 3Diagnostic Tests Flowchart Default Cycle dCYC How to Program Default CycleHow to Exit Programming Feature How to Program the Audio Signal Audio Signal AUdNot Cycle Pressed Used How to Read TableMode Card End Key Input Remove CoinESd Error Code Programming ErrHow to Program Error Code Programming LEr3SAT FRI Thur WED TUE MON SUN SAT FRI Thur WED TUE MON SUN OFF Final Description Status How to Enter Cycle ProgrammingHow to Program Cycle Agitate AgIt Cycle Programming CyFill Step Description Status How to Program Cycle Segment SEg1Agitate Description Status/Value Step SupplyDescription Status/Value StepExtract Description Programming Drain StepProgramming Cycle Time Display How to Program Number of Balance RetriesFahrenheit/Celsius t FC IR Access On/Off IrAHow to Program the IR Access On/Off How to Program Fahrenheit/CelsiusHow to Program Warm Water Temperature Hot Water Temperature FHWarm Water Temperature FHC How to Program Hot Water TemperatureHow to Program Cooldown Enable/ Temperature Cold Water Temperature FCCooldown Enable/Temperature Codn How to Program Cold Water TemperatureManual Rapid Advance On/Off rAEn How to Program the Production Test Cycle On/OffHow to Program the Manual Rapid Advance On/Off Production Test Cycle On/Off PtEnProgrammable Cycle Time Display PCtd How to Program in the Cycle Time DisplayHow to Program the Programmable Cycle Time Display No Cycle Time Display nCtdHow to Program the Pause/Resume Mode Slow Drain Detection Adjust SdAdSet Real-Time Clock rtC-’ How to Program the Time and DateLow Water Level FLo Manual Diagnostics On/Off dAEnHow to Program the Manual Diagnostics On/Off How to Program Low Water LevelHigh Water Level FHI How to Program Medium Water LevelHow to Program High Water Level Medium Water Level FnEdHow to Program Temperature Controlled Fill Temperature Controlled Fill Enable/Disable tCFAuto-Water Leak Detection ALd How to Program Auto-Water Leak DetectionCollecting Audit Information How to Enter Audit FeatureHow to Read Audit Data How to Exit Audit FeatureHow to Enter Manual Reset Manual ResetHow to Exit Testing Feature Testing Machine Electronic Control FunctionsHow to Enter Testing Feature How to Start TestsTxxx D001D002 D003Diagnostic Test Descriptions Frame Balance Switch Input Test Temperature Sensor Display TestVAC Switch Input Test VFD Drive Fault Input TestProduction Test Cycle Display Test Cycle Step Comments Production Test Cycle Quick Reference ChartDrAI then LoAg thenAg then RAg thenError Codes Door Error CodesRapid Advance Feature How to Use Rapid AdvanceHow to Exit Rapid Advance Feature Communications Mode How to Begin Communications with An External DeviceInfra-red Communications Default Cycles Default Cycles Cycle Stops Reclaim Delicates 90C 60C 40C 90C Perm 60C Perm Cycle reference CY08 CY09 Cycle Stops 40C Perm 70C Perm 50C Gentle 30C Gentle Blank CY17 CY18