Alliance Laundry Systems PHM1263R manual Production Test Cycle On/Off PtEn

Page 36

Programming Control

12.Production Test Cycle (On/Off) “PtEn”

This option allows the owner to enable or disable access to the production test cycle. Refer to Production Test Cycle section for more information.

How to Program the Production Test Cycle (On/Off)

1.Control must be in Manual Mode. Refer to Entering the Manual Mode.

2.Press the #3 (>) or the #6 (<) keypad until

Prog” appears in the display. Press the START (enter) keypad and “dCYC” will appear in the display.

3.Press the #3 (>) or the #6 (<) keypad to scroll through the programmable options until “PtEn” appears in the display.

4.When “PtEn” appears in the display, press the START (enter) keypad. The current Production Test Cycle status will appear in the display.

on” = Option Enabled “oFF” = Option Disabled

5.Press the #3 (>) or the #6 (<) keypad to change the current status.

6.Press the START (enter) keypad when the desired status appears in the display. The next option, “rAEn”, will appear in the display.

NOTE: To program “rAEn” (Manual Rapid Advance [on/off]), refer to option 13. To program other options, refer to the appropriate section.

How to Exit Programming Feature

Press the #5 (<) keypad until the control returns to Start Mode.

13.Manual Rapid Advance (On/Off) “rAEn”

This option allows the owner to enable or disable the rapid advance feature. Refer to Rapid Advance Feature section for more information.

How to Program the Manual Rapid Advance (On/Off)

1.Control must be in Manual Mode. Refer to Entering the Manual Mode.

2.Press the #3 (>) or the #6 (<) keypad until

Prog” appears in the display. Press the START (enter) keypad and “dCYC” will appear in the display.

3.Press the #3 (>) or the #6 (<) keypad to scroll through the programmable options until “rAEn” appears in the display.

4.When “rAEn” appears in the display, press the START (enter) keypad. The current Manual Rapid Advance status will appear in the display. “on” = Option Enabled

oFF” = Option Disabled

5.Press the #3 (>) or the #6 (<) keypad to change the current status.

6.Press the START (enter) keypad when the desired status appears in the display. The next option, rtc-”, will appear in the display.

NOTE: To program “nCtd” (No Cycle Time Display), refer to option 14. To program other options, refer to the appropriate section.

How to Exit Programming Feature

Press the #5 (<) keypad until the control returns to Start Mode.

34

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F8208801

Image 36
Contents Washer-Extractor Page W030 Contents Temperature Controlled Fill Enable/Disable tCF Model Identification Power Failure Recovery Preliminary InformationAbout the Control Glossary of TermsControl Identification Select Cycle Pads Refer to FigureDisplay Identification Light Emitting Diodes LEDs Refer to FigureFour 7-Segment Digits Washer-Extractor Operation Special Features Entering the Manual Mode How to Enter the Manual ModeManual Diagnostics Manual ProgrammingOption Description Default Value Range Number Display Programming ControlWhat Can Be Programmed? Programmable Options AvailableFLEn TEnPCoLd/Uarn/Hotor SUEnProgramming Control Manual Mode Flowchart Manual Programming Flowchart 1 Manual Programming Flowchart 2 Manual Programming Flowchart 3 Option available on software version 2 onlyDiagnostic Tests Flowchart Default Cycle dCYC How to Program Default CycleHow to Exit Programming Feature Audio Signal AUd How to Program the Audio SignalHow to Read Table Mode Card End Key InputRemove Coin Not Cycle Pressed UsedError Code Programming Err How to Program Error Code ProgrammingLEr3 ESdSAT FRI Thur WED TUE MON SUN SAT FRI Thur WED TUE MON SUN OFF How to Enter Cycle Programming How to Program Cycle Agitate AgItCycle Programming Cy Final Description StatusHow to Program Cycle Segment SEg1 Fill Step Description StatusSupply Description Status/ValueStep Agitate Description Status/Value StepProgramming Drain Step Extract DescriptionHow to Program Number of Balance Retries Programming Cycle Time DisplayIR Access On/Off IrA How to Program the IR Access On/OffHow to Program Fahrenheit/Celsius Fahrenheit/Celsius t FCHot Water Temperature FH Warm Water Temperature FHCHow to Program Hot Water Temperature How to Program Warm Water TemperatureCold Water Temperature FC Cooldown Enable/Temperature CodnHow to Program Cold Water Temperature How to Program Cooldown Enable/ TemperatureHow to Program the Production Test Cycle On/Off How to Program the Manual Rapid Advance On/OffProduction Test Cycle On/Off PtEn Manual Rapid Advance On/Off rAEnHow to Program in the Cycle Time Display How to Program the Programmable Cycle Time DisplayNo Cycle Time Display nCtd Programmable Cycle Time Display PCtdSlow Drain Detection Adjust SdAd How to Program the Pause/Resume ModeHow to Program the Time and Date Set Real-Time Clock rtC-’Manual Diagnostics On/Off dAEn How to Program the Manual Diagnostics On/OffHow to Program Low Water Level Low Water Level FLoHow to Program Medium Water Level How to Program High Water LevelMedium Water Level FnEd High Water Level FHITemperature Controlled Fill Enable/Disable tCF How to Program Temperature Controlled FillHow to Program Auto-Water Leak Detection Auto-Water Leak Detection ALdHow to Enter Audit Feature How to Read Audit DataHow to Exit Audit Feature Collecting Audit InformationManual Reset How to Enter Manual ResetTesting Machine Electronic Control Functions How to Enter Testing FeatureHow to Start Tests How to Exit Testing FeatureD001 D002D003 TxxxDiagnostic Test Descriptions Temperature Sensor Display Test VAC Switch Input TestVFD Drive Fault Input Test Frame Balance Switch Input TestProduction Test Cycle Production Test Cycle Quick Reference Chart Display Test Cycle Step CommentsLoAg then Ag thenRAg then DrAI thenError Codes Error Codes DoorRapid Advance Feature How to Use Rapid AdvanceHow to Exit Rapid Advance Feature Communications Mode How to Begin Communications with An External DeviceInfra-red Communications Default Cycles Default Cycles Cycle Stops Reclaim Delicates 90C 60C 40C 90C Perm 60C Perm Cycle reference CY08 CY09 Cycle Stops 40C Perm 70C Perm 50C Gentle 30C Gentle Blank CY17 CY18