Alliance Laundry Systems PHM1263R How to Program Cycle Segment SEg1, Fill Step Description Status

Page 29

How to Program Cycle Segment “SEg1”

There are eight programmable cycle segments. Within each segment, there are several programmable options.

1.Press the #3 (>) or the #6 (<) keypad to scroll through the eight programmable Cycle Segments until the desired segment appears in the display.

2.When the desired segment appears in the display, press the START (enter) keypad. “SgEn” (Segment Enable/Disable) will appear in the display.

3.Press the #3 (>) or the #6 (<) keypad to scroll through the Cycle Segment programmable options.

NOTE: If the Segment Enable/Disable is programmed “OFF”, the other Cycle Segment programming options can’t be accessed.

4.Press the START (enter) keypad when the desired Cycle Segment programmable option appears in the display.

Programming Segment Enable/Disable

1.When “SgEn” appears in the display, press the START (enter) keypad. The current Segment Enable/Disable status will appear in the display. “on” = Segment is enabled

oFF” = Segment is disabled

2.Press the #3 (>) or the #6 (<) keypad to change the current status.

NOTE: If the Segment Enable/Disable is programmed “oFF”, the other Cycle Segment programming options can’t be accessed.

3.Press the START (enter) keypad when the desired status appears in the display. The next Cycle Segment option, “FILL”, will appear in the display.

NOTE: To program “FILL” (Fill Step), continue to next Cycle Segment option. To program other options, press the #3 (>) or the #6 (<) keypad and refer to the appropriate section.

How to Exit Programming Feature

Press the #5 (<) keypad until the control returns to Start Mode.

Programming Control

Programming Fill Step

1.When “FILL” appears in the display, press the START (enter) keypad. The first Fill step programming option will appear in the display.

2.Press the #3 (>) or the #6 (<) keypad to scroll through the programmable Fill step options. Refer to Table 6.

NOTE: Fill Step “FLEn” must be enabled to scroll through all Fill Step options.

3.Press the START (enter) keypad when the desired option appears in the display. The current status will appear in the display. Refer to Table 6.

Fill Step

Description

Status

 

 

 

“FLEn”

Fill Step

“on”/”oFF”

 

Enable/Disable

 

 

 

 

“FLEU”

Fill Level

“HI” = high level

 

 

“nEd” = medium level

 

 

“Lo” = low level

 

 

“1-30”

 

 

 

“tEnP”

Fill Temperature

“CoLd” = Cold

 

 

“UArn” = Warm

 

 

“Hot” = Hot

 

 

(35°F-194°F [2°C-90°C])

 

 

 

Table 6

4.Press the #3 (>) or the #6 (<) keypad to change the current status.

5.Press the START (enter) keypad when the desired status appears in the display. The next Fill step option will appear in the display.

NOTE: To program “SUPL” (Supply Step), continue to next Cycle Segment option. To program other options, press the #3 (>) or the #6 (<) keypad the and refer to the appropriate section.

How to Exit Programming Feature

Press the #5(<) keypad until the control returns to Start Mode.

F8208801

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

27

Image 29
Contents Washer-Extractor Page W030 Contents Temperature Controlled Fill Enable/Disable tCF Model Identification Preliminary Information Power Failure RecoveryAbout the Control Glossary of TermsSelect Cycle Pads Refer to Figure Control IdentificationFour 7-Segment Digits Display IdentificationLight Emitting Diodes LEDs Refer to Figure Washer-Extractor Operation Special Features How to Enter the Manual Mode Entering the Manual ModeManual Diagnostics Manual ProgrammingProgramming Control Option Description Default Value Range Number DisplayWhat Can Be Programmed? Programmable Options AvailableTEnP FLEnCoLd/Uarn/Hotor SUEnProgramming Control Manual Mode Flowchart Manual Programming Flowchart 1 Manual Programming Flowchart 2 Option available on software version 2 only Manual Programming Flowchart 3Diagnostic Tests Flowchart How to Exit Programming Feature Default Cycle dCYCHow to Program Default Cycle How to Program the Audio Signal Audio Signal AUdMode Card End Key Input How to Read TableRemove Coin Not Cycle Pressed UsedHow to Program Error Code Programming Error Code Programming ErrLEr3 ESdSAT FRI Thur WED TUE MON SUN SAT FRI Thur WED TUE MON SUN OFF How to Program Cycle Agitate AgIt How to Enter Cycle ProgrammingCycle Programming Cy Final Description StatusFill Step Description Status How to Program Cycle Segment SEg1Description Status/Value SupplyStep Agitate Description Status/Value StepExtract Description Programming Drain StepProgramming Cycle Time Display How to Program Number of Balance RetriesHow to Program the IR Access On/Off IR Access On/Off IrAHow to Program Fahrenheit/Celsius Fahrenheit/Celsius t FCWarm Water Temperature FHC Hot Water Temperature FHHow to Program Hot Water Temperature How to Program Warm Water TemperatureCooldown Enable/Temperature Codn Cold Water Temperature FCHow to Program Cold Water Temperature How to Program Cooldown Enable/ TemperatureHow to Program the Manual Rapid Advance On/Off How to Program the Production Test Cycle On/OffProduction Test Cycle On/Off PtEn Manual Rapid Advance On/Off rAEnHow to Program the Programmable Cycle Time Display How to Program in the Cycle Time DisplayNo Cycle Time Display nCtd Programmable Cycle Time Display PCtdHow to Program the Pause/Resume Mode Slow Drain Detection Adjust SdAdSet Real-Time Clock rtC-’ How to Program the Time and DateHow to Program the Manual Diagnostics On/Off Manual Diagnostics On/Off dAEnHow to Program Low Water Level Low Water Level FLoHow to Program High Water Level How to Program Medium Water LevelMedium Water Level FnEd High Water Level FHIHow to Program Temperature Controlled Fill Temperature Controlled Fill Enable/Disable tCFAuto-Water Leak Detection ALd How to Program Auto-Water Leak DetectionHow to Read Audit Data How to Enter Audit FeatureHow to Exit Audit Feature Collecting Audit InformationHow to Enter Manual Reset Manual ResetHow to Enter Testing Feature Testing Machine Electronic Control FunctionsHow to Start Tests How to Exit Testing FeatureD002 D001D003 TxxxDiagnostic Test Descriptions VAC Switch Input Test Temperature Sensor Display TestVFD Drive Fault Input Test Frame Balance Switch Input TestProduction Test Cycle Display Test Cycle Step Comments Production Test Cycle Quick Reference ChartAg then LoAg thenRAg then DrAI thenError Codes Door Error CodesHow to Exit Rapid Advance Feature Rapid Advance FeatureHow to Use Rapid Advance Infra-red Communications Communications ModeHow to Begin Communications with An External Device Default Cycles Default Cycles Cycle Stops Reclaim Delicates 90C 60C 40C 90C Perm 60C Perm Cycle reference CY08 CY09 Cycle Stops 40C Perm 70C Perm 50C Gentle 30C Gentle Blank CY17 CY18