Alliance Laundry Systems PHM1263R manual Production Test Cycle Quick Reference Chart

Page 51

 

 

Testing Machine and Electronic Control Functions

 

 

 

Production Test Cycle Quick Reference Chart

 

 

 

Display

Test Cycle Step

Comments

 

 

 

“S xx”

FEC Control Software

xx is the software version number.

 

Version

 

 

 

 

“o xx”

Output Board Software

xx is the software version number.

 

Version

 

 

 

 

“Ct 3”

Control Type

xx is the control type.

 

 

 

“oPL”

Control Type

OPL.

 

 

 

“USA”

Control Type

Domestic

 

 

 

“drAn” or “PUnP”

Drain Type

Drain or Pump.

 

 

 

“tEnP”

Temp Sensor

Step skipped if not Temperature Sensor-equipped.

 

 

 

“HEAt”

Heater

Step skipped if not heater-equipped.

 

 

 

“rot”

Rotation Sensor

Step skipped if not Rotation Sensor-equipped.

 

 

 

“L dC” or “L AC”

Door Lock Type

“L dC” if 24 VDC lock or “L AC” if 240 VAC unlock solenoid.

 

 

 

“droP” or “drCL”

Door Status

Door open or closed.

 

 

 

“drUL” or “drLo”

Door Lock Status

Door will lock.

 

 

 

8.8.8.8.” + all LEDs

Display Test

All display elements are lit.

 

 

 

PAxx” where xx = 1

Keypad Test step

Advance after all keypads are pressed.

through 12

 

 

 

 

 

A xx

Access Panel Switch Test

xx is either “CL” for closed or “oP” for open.

 

 

 

“Cxxx” or “Pxxx”

Machine Type/Size

 

 

 

 

“HFIL”

Hot Fill to Low Level

All water turned off when Low Level reached.

 

 

 

“CFIL”

Cold Fill to Low Level

All water turned off when Low Level reached.

 

 

 

“bFIL”

Warm Fill to Low Level

All water turned off when Low Level reached.

 

 

 

“bFIH”

Warm Fill to High Level

All water turned off when High Level reached.

 

 

 

“S1” for supply or

Supply #1 or Compartment

 

“C2Co” for compartment

#2 Cold Fill

 

“S2” for supply or

Supply #2 or Compartment

 

“C2Ho” for compartment

#2 Hot Fill

 

“S3” for supply or

Supply #3 or Compartment

 

“C3Co” for compartment

#3 Cold Fill

 

“S4” for supply or

Supply #4 or Compartment

 

“C4Ho” for compartment

#4 Hot Fill

 

“oFLo”

Warm Fill to Overflow

 

 

 

 

“xxxF” degrees F or

Heat water to 110°F or

xxx is degree temperature. This step skipped if not temp-sensor-

“xxxC” degrees C

display temperature

equipped. Heater turned off when temperature reached.

depending on the

 

 

Fahrenheit/Celsius

 

 

programming parameter

 

 

 

 

 

 

Table 15 (continued)

F8208801

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

49

Image 51
Contents Washer-Extractor Page W030 Contents Temperature Controlled Fill Enable/Disable tCF Model Identification Glossary of Terms Power Failure RecoveryPreliminary Information About the ControlSelect Cycle Pads Refer to Figure Control IdentificationDisplay Identification Light Emitting Diodes LEDs Refer to FigureFour 7-Segment Digits Washer-Extractor Operation Special Features Manual Programming Entering the Manual ModeHow to Enter the Manual Mode Manual DiagnosticsProgrammable Options Available Option Description Default Value Range Number DisplayProgramming Control What Can Be Programmed?SUEn FLEnTEnP CoLd/Uarn/HotorProgramming Control Manual Mode Flowchart Manual Programming Flowchart 1 Manual Programming Flowchart 2 Option available on software version 2 only Manual Programming Flowchart 3Diagnostic Tests Flowchart Default Cycle dCYC How to Program Default CycleHow to Exit Programming Feature How to Program the Audio Signal Audio Signal AUdNot Cycle Pressed Used How to Read TableMode Card End Key Input Remove CoinESd Error Code Programming ErrHow to Program Error Code Programming LEr3SAT FRI Thur WED TUE MON SUN SAT FRI Thur WED TUE MON SUN OFF Final Description Status How to Enter Cycle ProgrammingHow to Program Cycle Agitate AgIt Cycle Programming CyFill Step Description Status How to Program Cycle Segment SEg1Agitate Description Status/Value Step SupplyDescription Status/Value StepExtract Description Programming Drain StepProgramming Cycle Time Display How to Program Number of Balance RetriesFahrenheit/Celsius t FC IR Access On/Off IrAHow to Program the IR Access On/Off How to Program Fahrenheit/CelsiusHow to Program Warm Water Temperature Hot Water Temperature FHWarm Water Temperature FHC How to Program Hot Water TemperatureHow to Program Cooldown Enable/ Temperature Cold Water Temperature FCCooldown Enable/Temperature Codn How to Program Cold Water TemperatureManual Rapid Advance On/Off rAEn How to Program the Production Test Cycle On/OffHow to Program the Manual Rapid Advance On/Off Production Test Cycle On/Off PtEnProgrammable Cycle Time Display PCtd How to Program in the Cycle Time DisplayHow to Program the Programmable Cycle Time Display No Cycle Time Display nCtdHow to Program the Pause/Resume Mode Slow Drain Detection Adjust SdAdSet Real-Time Clock rtC-’ How to Program the Time and DateLow Water Level FLo Manual Diagnostics On/Off dAEnHow to Program the Manual Diagnostics On/Off How to Program Low Water LevelHigh Water Level FHI How to Program Medium Water LevelHow to Program High Water Level Medium Water Level FnEdHow to Program Temperature Controlled Fill Temperature Controlled Fill Enable/Disable tCFAuto-Water Leak Detection ALd How to Program Auto-Water Leak DetectionCollecting Audit Information How to Enter Audit FeatureHow to Read Audit Data How to Exit Audit FeatureHow to Enter Manual Reset Manual ResetHow to Exit Testing Feature Testing Machine Electronic Control FunctionsHow to Enter Testing Feature How to Start TestsTxxx D001D002 D003Diagnostic Test Descriptions Frame Balance Switch Input Test Temperature Sensor Display TestVAC Switch Input Test VFD Drive Fault Input TestProduction Test Cycle Display Test Cycle Step Comments Production Test Cycle Quick Reference ChartDrAI then LoAg thenAg then RAg thenError Codes Door Error CodesRapid Advance Feature How to Use Rapid AdvanceHow to Exit Rapid Advance Feature Communications Mode How to Begin Communications with An External DeviceInfra-red Communications Default Cycles Default Cycles Cycle Stops Reclaim Delicates 90C 60C 40C 90C Perm 60C Perm Cycle reference CY08 CY09 Cycle Stops 40C Perm 70C Perm 50C Gentle 30C Gentle Blank CY17 CY18