ADC AD-464 service manual Steam Models ADS-464

Page 14

B. STEAM MODELS (ADS-464)

MAXIMUM CAPACITY (DRY WEIGHT)

460 lbs.

 

209.09 kg

TOTAL WEIGHT

11,000 lbs.

 

4,949.6 kg

TOTAL SHIPPING WEIGHT (STRETCH WRAP/SKID)

11,162 lbs.

 

5,063.08 kg

TILT HEIGHT

137-1/4"

 

348.6 cm

OPERATING HEIGHT

114-1/2"

 

290.83 cm

FULL TILT DEPTH

117-1/2"

 

298.45 cm

OPERATING DEPTH

95"

 

241.3 cm

WIDTH

122"

 

309.88 cm

TILT LOAD (REAR TILT)

 

15º

 

 

 

 

TILT UNLOAD (FRONT TILT)

 

15º

 

 

 

 

UNLOADING HEIGHT FROM FLOOR

43-3/4"

 

111.12 cm

LOADING HEIGHT FROM FLOOR

65-5/8"

 

166.69 cm

DOOR OPENING

53-1/4" x 49"

 

135.26 cm x 124.46 cm

BASKET DIAMETER

69-1/8"

 

175.58 cm

BASKET DEPTH

80-5/16"

 

203.99 cm

BASKET VOLUME

175 cu. ft.

 

4.96 cu. m

MINIMUM LOAD SIZE

250 lbs.

 

113.64 kg

MAXIMUM LOAD SIZE

460lbs.

 

209.09 kg

BOILER HORSEPOWER

 

60 Bhp

 

 

 

 

STEAM INLET CONNECTION SIZE*

2-1/2" N.P.T.

 

-

STEAM RETURN CONNECTION SIZE (2 PLACES)

1 1/4" N.P.T.

 

-

BASKET MOTORS (2 MOTORS)

(2) 5 HP

 

(2) 3.73 kw

BLOWER MOTOR

25 HP

 

18.65 kw

BLOWER MAXIMUM AIRFLOW

13,000 cfm

 

368 cmm

MAXIMUM DUCT BACK PRESSURE

1.25" (W.C.)

 

3.1 mbar

MINIMUM DUCT DIAMEMTER

24"

 

60.96 cm

COMPRESSED AIR PRESSURE REQUIRED

80 psi (±10 psi)

 

5.63 bar (±.7)

COMPRESSED AIR VOLUME REQUIRED

20 cf/hr

 

.57 cm/hr

COMPRESSED AIR CONNECTION

3/8" N.P.T.

 

-

Shaded areas are stated in metric equivalents

 

 

 

* Size of piping to dryer varies with installation conditions. Contact factory for assistance.

NOTE: ADC reserves the right to make changes in specifications at any time, without notice or obligation.

10

Image 14
Contents American Dryer Corporation Retain This Manual In a Safe Place For Future Reference Important Note to PurchaserFor Your Safety Page Table of Contents Section AIR JET System Section Pendant AssemblySection Sprinkler System Safety Precautions Explosion could ResultStandards National Electric Code ANSI/NFPA no -LATEST EditionLiquids Routine MaintenanceCleaning Monthly Lubrication Adjustments Days After Installation and Every 6 Months ThereafterSpecifications GAS Models ADG-464Steam Models ADS-464 Electrical Service Specifications ADG-464 GASInstallation Requirements Enclosure / AIR Supply / Exhaust RequirementsOperational Service Check Procedure Electrical Requirements and GAS RequirementsComponent DESCRIPTION/REPLACEMENT Tumbler Support and Drive SystemPage Main AIR BLOWER/HEAT Reclaimer System +Z=X Filter element can be cleaned with soap and water Compressed AIR SystemPage Page Page Safety Devices Safety Devices Locations/Functions/Messages Blower Squirrel Cage Fan Motor Assembly Pulley Removal Page Freely Important do not Overtighten V-BELTSImportant do not Overtighten V-BELTS Blower Squirrel Cage Fan Electrical Components Page Tumbler Basket System Page Page Important do not Overtighten Turnbuckle Important do not Overtighten Turnbuckle Result in Damage to the Dryer and will Void the Warranty Important do not Overtighten Bolts Page Rotational Sensor Assembly Current Limiting Device is RequiredPage TOP of Tumbler Basket Temperature Door Assembly Tumbler Basket Electrical Components Page PLC Programmable Logic Controller System PLC Programmable Logic Controller DescriptionPage Page 111 PLC Programmable Logic Controller Component Replacement Page Page RTD Page Switch #1 Recycling Mode Page Page Page Combustion Air Damper Page Page Page Burner Air Switch Page Page Page Page Page Page Heat Reclaimer Settings Page Page Important Allow a full 72 hours for the silicone to cure Page Page Page Page Lint DRAWER/LINT Chamber Switches Base SectionPage Page Resistive Temperature Device RTD RTD Resistive Temperature Device Locations Sprinkler System Sprinkler System DescriptionPage MAN3190 Page AIR JET System AIR JET SystemStack Valve Assembly Pneumatic ValveImportant Take Notice ... small components Page MAN4223 Internal Pilot and External Pilot Air Supply Pendant Assembly Pendant Assembly DescriptionADC450186 05/27/99-25 01/14/00-15