ADC AD-464 service manual Important do not Overtighten V-BELTS

Page 32

5)Remove the two (2) left hand jam nuts and the washers.

6)Remove the blower (squirrel cage fan) along with the 3/8" x 3/8" x 3" key from the blower shaft.

NOTE: Install the 3/8" x 3/8" x 3" key on to the blower shaft before installing the blower (squirrel cage fan).

7)To install new blower (squirrel cage) fan, reverse Step #7 thru Step #1. d.V-Belt Replacement

1)Discontinue electrical service to the dryer.

2)Remove the belt guard.

3)Loosen the bolts securing the blower motor to the motor base; a. Ease off on the tension bolt.

4)Slide the blower motor forward.

5)Remove and replace V-belts.

NOTE: For proper belt replacement, the V-belts should be replaced in matched sets (both belts).

6) Tighten/secure the tension bolt.

IMPORTANT: DO NOT OVERTIGHTEN V-BELTS.

7)Using a straight edge, make certain that the motor pulley and the V-belts are properly aligned.

8)Secure/tighten the bolts from the motor to the motor base.

9)Reinstall the belt guard removed in Step #2.

10)Reestablish electrical service to the dryer.

e.Blower Shaft Replacement

The procedure to replace the blower shaft is the same procedure used to replace the shrouded pillow block bearing. (Refer to page 26 and page 27.)

28

Image 32
Contents American Dryer Corporation Retain This Manual In a Safe Place For Future Reference Important Note to PurchaserFor Your Safety Page Table of Contents Section AIR JET System Section Pendant AssemblySection Sprinkler System Safety Precautions Explosion could ResultStandards National Electric Code ANSI/NFPA no -LATEST EditionLiquids Routine MaintenanceCleaning Monthly Lubrication Adjustments Days After Installation and Every 6 Months ThereafterSpecifications GAS Models ADG-464Steam Models ADS-464 Electrical Service Specifications ADG-464 GASInstallation Requirements Enclosure / AIR Supply / Exhaust RequirementsOperational Service Check Procedure Electrical Requirements and GAS RequirementsComponent DESCRIPTION/REPLACEMENT Tumbler Support and Drive SystemPage Main AIR BLOWER/HEAT Reclaimer System +Z=X Filter element can be cleaned with soap and water Compressed AIR SystemPage Page Page Safety Devices Safety Devices Locations/Functions/Messages Blower Squirrel Cage Fan Motor Assembly Pulley Removal Page Freely Important do not Overtighten V-BELTSImportant do not Overtighten V-BELTS Blower Squirrel Cage Fan Electrical Components Page Tumbler Basket System Page Page Important do not Overtighten Turnbuckle Important do not Overtighten Turnbuckle Result in Damage to the Dryer and will Void the Warranty Important do not Overtighten Bolts Page Rotational Sensor Assembly Current Limiting Device is RequiredPage TOP of Tumbler Basket Temperature Door Assembly Tumbler Basket Electrical Components Page PLC Programmable Logic Controller System PLC Programmable Logic Controller DescriptionPage Page 111 PLC Programmable Logic Controller Component Replacement Page Page RTD Page Switch #1 Recycling Mode Page Page Page Combustion Air Damper Page Page Page Burner Air Switch Page Page Page Page Page Page Heat Reclaimer Settings Page Page Important Allow a full 72 hours for the silicone to cure Page Page Page Page Lint DRAWER/LINT Chamber Switches Base SectionPage Page Resistive Temperature Device RTD RTD Resistive Temperature Device Locations Sprinkler System Sprinkler System DescriptionPage MAN3190 Page AIR JET System AIR JET SystemStack Valve Assembly Pneumatic ValveImportant Take Notice ... small components Page MAN4223 Internal Pilot and External Pilot Air Supply Pendant Assembly Pendant Assembly DescriptionADC450186 05/27/99-25 01/14/00-15