Texas Instruments 3138 155 232931 manual Important Notice

Page 90

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer'srisk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products

 

Applications

 

Amplifiers

amplifier.ti.com

Audio

www.ti.com/audio

Data Converters

dataconverter.ti.com

Automotive

www.ti.com/automotive

DSP

dsp.ti.com

Broadband

www.ti.com/broadband

Interface

interface.ti.com

Digital Control

www.ti.com/digitalcontrol

Logic

logic.ti.com

Military

www.ti.com/military

Power Mgmt

power.ti.com

Optical Networking

www.ti.com/opticalnetwork

Microcontrollers

microcontroller.ti.com

Security

www.ti.com/security

RFID

www.ti-rfid.com

Telephony

www.ti.com/telephony

Low Power

www.ti.com/lpw

Video & Imaging

www.ti.com/video

Wireless

 

 

 

 

 

Wireless

www.ti.com/wireless

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Copyright © 2007, Texas Instruments Incorporated

Page 89 Page 90
Image 90
Page 89 Page 90
Contents Key Features ApplicationsProduct Description Table of contents RF Data Buffering Ordering Information General Information Abbreviations ITU-TReferences Features Parameter Min Max Units Condition Absolute Maximum RatingsOperating Conditions Parameter Min Typ Max Units ConditionTransmit Section Electrical SpecificationsOverall Parameter Min Typ Max Unit Condition / NoteReceive Section Rssi / Carrier Sense If SectionFrequency Synthesizer Section Digital Inputs/Outputs VDDBattery Monitor Power SupplyVoltage Regulator CC2420 Pin Assignment Pin Pin Name Pin type Pin DescriptionAvddadc CC2420 simplified block diagram Circuit DescriptionCC2420 Input / output matching Power supply decoupling and filteringApplication Circuit Bias resistorOverview of external components DescriptionTransceiver Transceiver Bill of materials for the application circuits Symbol Chip sequence C0, C1, C2, … , C31 Ieee 802.15.4 Modulation FormatConfiguration Overview PhaseEvaluation Software SmartRF Studio user interface13 4-wire Serial Configuration and Data Interface Pin configurationRegister access SPI timing specification Status byte Parameter Symbol Min Max Units ConditionsRAM access Configuration registers write and read operations via SPI CC2420 RAM Memory Space Fifo access Multiple SPI accessAddress Byte Ordering Name Description Configuration interface Microcontroller Interface and Pin DescriptionReceive mode Rxfifo overflowPin activity examples during receive Demodulator, Symbol Synchroniser and Data Decision Demodulator Simplified Block Diagram Frame FormatTransmitted Synchronisation Header Length field MAC protocol data unitFormat of the Frame Control Field FCF Frame check sequence Buffered transmit mode Buffered receive modeRF Data Buffering Unbuffered, serial mode FifopAddress Recognition Acknowledge FramesAcknowledge frame format Radio control state machine Radio control states Nonce / counter MAC Security Operations Encryption and AuthenticationKeys Ieee 802.15.4 NonceCC2420 Security Flag Byte Stand-alone encryption In-line security operationsCTR mode encryption / decryption CBC-MAC21.7 CCM Rssi / Energy Detection Linear if and AGC SettingsMode LMIC Time TimingLink Quality Indication ValueRF Level dBm Clear Channel Assessment Frequency and Channel ProgrammingVoltage Regulator Output Power ProgrammingVCO and PLL Self-Calibration 27.1 VCOBattery Monitor Voltage regulator, simplified schematicCrystal Oscillator Crystal oscillator component values Input / Output MatchingTransmitter Test Modes Unmodulated carrierCC2420 Modulated spectrum plot System Considerations and Guidelines Battery operated systems Low-cost systemsBER / PER measurements PCB Layout Recommendations Antenna ConsiderationsCC2420 Configuration Registers Address Register Register type DescriptionConfiguration registers overview SaesBit Field Name Reset Main 0x10 Main Control RegisterXOSC16MBYPASS MDMCTRL0 0x11 Modem Control Register Reservedframemode Pancoordinator AdrdecodeCCAHYST20 CCAMODE10 Autocrc Autoack Preamblelength CORRTHR40 Demodavgmode Modulationmode MDMCTRL1 0x12- Modem Control RegisterRssi 0x13 Rssi and CCA Status and Control Register RSSIVAL70Syncword 0x14 Sync Word Txctrl 0x15 Transmit Control RegisterRXCTRL0 0x16 Receive control register RXMIXBUFCUR10RXCTRL1 0x17 Receive control register Fsctrl 0x18 Frequency Synthesizer Control and Status Caldone Calrunning Locklength LockstatusSECCTRL0 0x19 Security Control Register SECMODE10Sectxl Secrxl Battmon 0x1B Battery Monitor Control registerSECCTRL1 0x1A Security Control Register Battmonok Battmonen BattmonvoltageManfidl 0x1E Manufacturer ID, Lower 16 Bit IOCFG0 0x1C I/O Configuration RegisterIOCFG1 0x1D I/O Configuration Register HSSDSRC20 SFDMUX40 CCAMUX40Manfidh 0x1F Manufacturer ID, Upper 16 Bit Fsmtc 0x20 Finite state machine time constantsManand 0x21 Manual signal and override register1 Isused = is * Isandmask + IsormaskVgagainoe Manor 0x22 Manual signal or override registerAgcctrl 0x23 AGC Control LnamixgainmodeoAGCTST0 0x24 AGC Test Register AGCTST1 0x25 AGC Test RegisterAGCTST2 0x26 AGC Test Register FSTST0 0x27 Frequency Synthesizer Test Register FSTST1 0x28 Frequency Synthesizer Test RegisterFSTST2 0x29 Frequency Synthesizer Test Register FSTST3 0x2A Frequency Synthesizer Test Register Rxbpftst 0x2B Receiver Bandpass Filters Test RegisterFsmstate 0x2C Finite state machine information Adcclockdisable Adctst 0x2D ADC Test RegisterDactst 0x2E DAC Test Register Txfifo 0x3E Transmit Fifo Byte register Oscillator must be running for accessing the RxfifoToptst 0x2F Top Level Test Register Rxfifo 0x3F Receive Fifo Byte registerTest Output Signals CCA test signal select tableSignal output on CCA pin Description SFD test signal select table Signal output on SFD pin DescriptionPackage Description QLP Quad Leadless Package QLPSoldering information Recommended layout for package QLPPackage thermal properties Thermal resistanceTube Specification 40.3 Plastic tube specification40.4 Carrier tape and reel specification Tape and Reel SpecificationGeneral Information 42.1 Document HistoryRevision Date Description/Changes Data Sheet Identification Product Status Definition Product Status DefinitionsAddress Information TI Worldwide Technical Support InternetProduct Information Centers 2007, Texas Instruments. All rights reserved Important Notice
Top Page Image Contents