Multi-Tech Systems MVP103, 410 manual Configuration

Page 15

Chapter 2 - Configuration

5b. Configure Call Signaling Port. Unlike station (FXS) ports, which require a unique value for each channel, trunk (FXO) ports require that the same Call Signaling Port value be used on all trunk (FXO) ports that are registered to the same Communication Manager PBX. Configure this to a unique value that is not being used by another station (FXS) or trunk (DID) port on this MultiVOIP unit. This port value must fall within the range of port values supported by Communication Manager and should match the “Far-end Listen Port” value configured in the Communication Manager “Signaling Group” (“Display Signaling Group”) form (dialog box). All FXO ports on this MultiVOIP will use the same Signaling Group for communication with the CM Server.

Note that several other fields in the Communication Manager “Signaling Group” form (dialog box) must be set to accommodate operation with the MultiVOIP:

Group Type

= h.323

 

 

Remote Office?

= n

 

 

RRQ Required?

= y

 

 

Direct IP-IP Audio Connection?

= y

 

 

IP Audio Hairpinning?

=n

 

 

Calls Share IP Sig Connection

=y

 

 

5c. Configure Delay before Dial value. This is the delay after the MultiVOIP goes off hook before it dials a number to the attached PSTN line. Some PSTN lines may require more than the default 400 ms value. Configure as appropriate for the PSTN lines you are using. If you are not sure, leave the default value in place.

5d. Configure Gateway Name. This should match the value configured for this MultiVOIP unit in the Communication Manager “IP Node Names” and “Signaling Group” forms.

5e. Configure Primary Gatekeeper IP Address. This must be configured to match the IP address of the

CLAN or PROCR card in the “IP Node Names” form of the primary Communication Manager Gatekeeper unit. Do not change the RAS Port and leave the Gatekeeper name field blank.

5f. Configure IP addresses for Alternate Gatekeeper1 and Alternate Gatekeeper 2 (optional). These must be configured to match the IP address of the respective CLAN or PROCR card in the PBX unit serving as the Alternate Gatekeeper. This field appears in IP Node Names form of the Communication Manager software for that PBX. If you are using the MultiVOIP Gatekeeper as an alternate gatekeeper, enter the IP address of the MultiVOIP. The alternate MultiVOIP gatekeeper must appear after any Communication Manager alternate gatekeepers.

Multi-Tech Systems, Inc. Avaya Communication Manager Guide

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents MultiVOIP Revision Date Description Configuration GuideContents Introduction IntroductionMultiVOIP in Avaya Communication Manager System Configuration ConfigurationChannel RTP Port Rtcp Port T38 Port Configuration Configuration Bandwidth per Channel Voice Frames per IP Packet Communication Manager MultiVOIP FXS Channels Configuration Configuration Communication Manager MultiVOIP FXO Channels Configuration = Isdn Communication Manager MultiVOIP did Channels Configuration = Isdn Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Regional Parameter Definitions Field Name Values Description Regional Parameters screenField Name Values Description Regional Parameter DefinitionsTone Pair Values Related MultiVOIP Setup Parameters Communication Manager SettingsRelated MultiVOIP Setup Parameters Version 4 Parameters Voice/Fax Parameters Channel to be configured is selected here Mode Fax FRF 11 T.38 Fax EnableFax Volume Jitter Value Default =Advanced Features Jitter Automatic Auto DisconnectInterface Parameters Related MultiVOIP Setup Parameters FXS Not applicable to FXS interface Dialing Options FXO Interface Parameter DefinitionsFXO Disconnect On cont’d CID Number Voip Caller ID Case #4 Remote FXS call on H.323 voip system Did Options Policy GK General SettingsGK General Settings Definitions Activity ConfigurationRAS Parameters GK General Settings Definitions cont’dGatekeeper Endpoints Command Buttons ID alias of the endpoint originating the call Gatekeeper CallsCurrent Calls Field Definitions Number. a sequential number for identification in the listID identifies the call with which the message is associated Call Details Field DefinitionsConference ID number CID is a unique non-zero value created Conference will have the same CIDReason associated with the last state of the call Total amount of bandwidth used by the callType of conference request create, invite or join Last reported state of the callAddress and port number H.323 alias name used to make the callE164 alias phone number used to make the call An e-mail address used to make the callOptions Gatekeeper Network ParametersNetwork Parameter Definitions Field Name Values Description Status InformationLine Hunting Information ARQCall Mode GK-ID Public Gatekeeper ServicesServices Screen Definitions Field Name Values Description GK Defined ServicesDynamic Miscellaneous MiscellaneousComm Mgr Dialing Example #1 a local station-to-station call Remote Configuration Miscellaneous MVP210-AV Rev a MVP130-AV RevMVP130-AV Rev a MVP130-AV-FXS Rev aMiscellaneous Link Management Feature Issues Index IndexCoder field FRF11 Gatekeeper Response to field GK General Settings, RAS DID-DPO FXO Trunk Group form fields to set Dtmf Gain Unregister endpoints command Dtmf Gain High Tones
Top Page Image Contents