Multi-Tech Systems 410, MVP103 manual Configuration

Page 6

Chapter 2 – Configuration

Chapter 2 - Configuration

Configuring MultiVOIP for Avaya Communication Manager Use

To configure the MultiVOIP unit within such a system (similar to that in Figure 1), use the Communication Manager Parameters screen within the MultiVOIP program. If “Register with Communication Manager Gatekeeper” is selected, then many parameters must assume default values and those will be grayed out on the screen. In setting up the MultiVOIP unit for Communication Manager use, bear in mind that you may configure the MultiVOIP to operate with any combination of stations (FXS) and/or trunks (FXO/DID).

1.Configure IP Parameters

1a. Configure the IP address, gateway address, and mask used by the MultiVOIP unit in the Configuration IP Parameters screen of the MultiVOIP program. The IP address must match that used in the Communication Manager “Change Node Names IP” form (dialog box).

1b. DiffServ PHB (Per Hop Behavior) values pertain to a differential prioritizing system for IP packets as handled by DiffServ-compatible routers. There are 64 values, each with an elaborate technical description. These descriptions are found in TCP/IP standards RFC2474, RFC2597, and, for present purposes, in RFC3246, which describes the value 34 (34 decimal; 22 hex) for Assured Forwarding behavior (default for Call Control PHB) and the value 46 (46 decimal; 2E hexadecimal) for Expedited Forwarding behavior (default for Voip Media PHB).

If you wish to use just one DiffServ PHB value, Ayaya recommends the value 46 (46 decimal; 2E hex) for both Call Control and VOIP Media.

1c. If you require that the MultiVOIP get its IP address from a DHCP server, select the “Enable DHCP” option. The DHCP server must be located at the same site as the MultiVOIP so it is available in the event of wan link failure. The DHCP server must issue an IP address that is statically defined on the DHCP server so that the MultiVOIP gets the same IP address all the time.

1d. TDM Routing Option. Calls placed between ports on the same MultiVOIP voice channel board will normally be routed over the MultiVOIP’s internal TDM (Time Division Multiplexed) bus. TDM calls have less delay than calls routed over IP. On MVP410/810-AV models, calls between channels 1-4 or channels 5-8 will be TDM routed. Calls between voice boards (for example, channel 1 calling channel 5) will be IP routed. If you require all calls to be IP routed, disable the “use TDM Routing for Intra-Gateway Calls” option. This should not normally be required, so it is recommended that you leave TDM Routing enabled.

6

Multi-Tech Systems, Inc. Avaya Communication Manager Guide

Page 5 Page 7
Image 6
Page 5 Page 7
Contents MultiVOIP Configuration Guide Revision Date DescriptionContents Introduction IntroductionMultiVOIP in Avaya Communication Manager System Configuration ConfigurationChannel RTP Port Rtcp Port T38 Port Configuration Configuration Bandwidth per Channel Voice Frames per IP Packet Communication Manager MultiVOIP FXS Channels Configuration Configuration Communication Manager MultiVOIP FXO Channels Configuration = Isdn Communication Manager MultiVOIP did Channels Configuration = Isdn Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Regional Parameters screen Regional Parameter Definitions Field Name Values DescriptionRegional Parameter Definitions Field Name Values DescriptionTone Pair Values Communication Manager Settings Related MultiVOIP Setup ParametersRelated MultiVOIP Setup Parameters Version 4 Parameters Voice/Fax Parameters Channel to be configured is selected here Jitter Value Default = Fax EnableFax Volume Mode Fax FRF 11 T.38Advanced Features Jitter Auto Disconnect AutomaticInterface Parameters Related MultiVOIP Setup Parameters FXS Not applicable to FXS interface FXO Interface Parameter Definitions Dialing OptionsFXO Disconnect On cont’d CID Number Voip Caller ID Case #4 Remote FXS call on H.323 voip system Did Options Activity Configuration GK General SettingsGK General Settings Definitions PolicyGK General Settings Definitions cont’d RAS ParametersGatekeeper Endpoints Command Buttons Number. a sequential number for identification in the list Gatekeeper CallsCurrent Calls Field Definitions ID alias of the endpoint originating the callConference will have the same CID Call Details Field DefinitionsConference ID number CID is a unique non-zero value created ID identifies the call with which the message is associatedLast reported state of the call Total amount of bandwidth used by the callType of conference request create, invite or join Reason associated with the last state of the callAn e-mail address used to make the call H.323 alias name used to make the callE164 alias phone number used to make the call Address and port numberField Name Values Description Status Information Gatekeeper Network ParametersNetwork Parameter Definitions OptionsARQ Line Hunting InformationCall Mode GK-ID Field Name Values Description GK Defined Services Gatekeeper ServicesServices Screen Definitions PublicDynamic Miscellaneous MiscellaneousComm Mgr Dialing Example #1 a local station-to-station call Remote Configuration Miscellaneous MVP130-AV-FXS Rev a MVP130-AV RevMVP130-AV Rev a MVP210-AV Rev aMiscellaneous Link Management Feature Issues Index IndexCoder field FRF11 Gatekeeper Response to field GK General Settings, RAS DID-DPO FXO Trunk Group form fields to set Dtmf Gain Unregister endpoints command Dtmf Gain High Tones
Top Page Image Contents