Multi-Tech Systems 410, MVP103 Call Details Field Definitions, Conference will have the same CID

Page 56

Chapter 3 – Related MultiVOIP Setup Parameters

A Call Details screen for a call in progress can be launched either by clicking on the “Call Details” button for a selected call in the Current Calls screen, or by double-clicking on a selected call listed in the Current Calls screen. The Call Details screen contains general information about the call, as well as details about the call’s source endpoint and destination endpoint.

Clicking on an in-progress call, or using the “Call Details” button, yields full details about the call

The Call Details screen consists of three panes: Call General Info, Destination Info, and Source Info. We describe the fields for each of these panes in a separate table below.

 

 

Call Details Field Definitions

Field Name

Values

Description

Call General Info

 

Call No.

 

Call Number. Accession number identifying a call in progress.

Cid Sum

 

The conference ID number (CID) is a unique non-zero value created

 

 

by the calling endpoint and passed in various H.225.0 messages. The

 

 

CID identifies the conference with which the message is associated.

 

 

Therefore, messages from all endpoints participating in the same

 

 

conference will have the same CID.

Call ID Sum

 

The call ID number is a globally unique non-zero value created by the

 

 

calling endpoint and passed in various H.225.0 messages. The Call

 

 

ID identifies the call with which the message is associated.

Call Model

direct

Indicates whether the call is direct or routed.

 

OR

For direct-mode calls, the gatekeeper gives each endpoint involved in the call

 

the destination address of the other and establishes a common call-signaling

 

routed

 

channel for them to use during the call. Then the two endpoints conduct the

 

 

 

 

call without further gatekeeper involvement.

 

 

For routed-mode calls, the gatekeeper establishes a connection between the

 

 

two endpoints but keeps itself involved in call signaling for the duration of

 

 

the call. In routed mode, the gatekeeper keeps a call-signaling channel open

 

 

for the entire duration of the call. As a call-management service, the

 

 

gatekeeper can change the routing of the call (by line hunting) while the calls

 

 

is in progress. If the gatekeeper is to implement supplementary (H.450)

 

 

services, it must operate in routed mode.

56

Multi-Tech Systems, Inc. Avaya Communication Manager Guide

Page 55 Page 57
Image 56
Page 55 Page 57
Contents MultiVOIP Configuration Guide Revision Date DescriptionContents Introduction IntroductionMultiVOIP in Avaya Communication Manager System Configuration ConfigurationChannel RTP Port Rtcp Port T38 Port Configuration Configuration Bandwidth per Channel Voice Frames per IP Packet Communication Manager MultiVOIP FXS Channels Configuration Configuration Communication Manager MultiVOIP FXO Channels Configuration = Isdn Communication Manager MultiVOIP did Channels Configuration = Isdn Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Regional Parameters screen Regional Parameter Definitions Field Name Values DescriptionRegional Parameter Definitions Field Name Values DescriptionTone Pair Values Communication Manager Settings Related MultiVOIP Setup ParametersRelated MultiVOIP Setup Parameters Version 4 Parameters Voice/Fax Parameters Channel to be configured is selected here Fax Enable Fax VolumeJitter Value Default = Mode Fax FRF 11 T.38Advanced Features Jitter Auto Disconnect AutomaticInterface Parameters Related MultiVOIP Setup Parameters FXS Not applicable to FXS interface FXO Interface Parameter Definitions Dialing OptionsFXO Disconnect On cont’d CID Number Voip Caller ID Case #4 Remote FXS call on H.323 voip system Did Options GK General Settings GK General Settings DefinitionsActivity Configuration PolicyGK General Settings Definitions cont’d RAS ParametersGatekeeper Endpoints Command Buttons Gatekeeper Calls Current Calls Field DefinitionsNumber. a sequential number for identification in the list ID alias of the endpoint originating the callCall Details Field Definitions Conference ID number CID is a unique non-zero value createdConference will have the same CID ID identifies the call with which the message is associatedTotal amount of bandwidth used by the call Type of conference request create, invite or joinLast reported state of the call Reason associated with the last state of the callH.323 alias name used to make the call E164 alias phone number used to make the callAn e-mail address used to make the call Address and port numberGatekeeper Network Parameters Network Parameter DefinitionsField Name Values Description Status Information OptionsARQ Line Hunting InformationCall Mode GK-ID Gatekeeper Services Services Screen DefinitionsField Name Values Description GK Defined Services PublicDynamic Miscellaneous MiscellaneousComm Mgr Dialing Example #1 a local station-to-station call Remote Configuration Miscellaneous MVP130-AV Rev MVP130-AV Rev aMVP130-AV-FXS Rev a MVP210-AV Rev aMiscellaneous Link Management Feature Issues Index IndexCoder field FRF11 Gatekeeper Response to field GK General Settings, RAS DID-DPO FXO Trunk Group form fields to set Dtmf Gain Unregister endpoints command Dtmf Gain High Tones
Top Page Image Contents