Multi-Tech Systems 410, MVP103 manual Configuration

Page 20

Chapter 2 – Configuration

7.Configure MultiVOIP gatekeeper (except for the MVP130 Models) to provide survivability to IP phones and local FXS/FXO/DID ports.

If you are using Avaya IP phones in addition to the MultiVOIP, you must configure the MultiVOIP gatekeeper to provide survivability for the IP phones and local FXS/FXO/DID ports in the event of WAN link failure.

7a. In the MultiVOIP’s Gatekeeper Endpoints screen, add predefined endpoints to the gatekeeper.

One endpoint entry is required for each FXS port or IP phone. Only one entry is required for one or more FXO ports per MultiVOIP gateway. Only one entry is required for one or more DID ports per MultiVOIP gateway.

7b. To add an entry for a MultiVOIP FXS port, configure Endpoint Type, Product ID, Names, Phones,

Registration IP, and Security code fields as indicated below. Configure the Names field with a unique descriptive identifier. The information contained in the Names and Phones fields will be used for Caller ID purposes in survivable mode. Configure Phones and Security Code to match the values configured for this station in Communication Manager. The Registration IP should match the IP address of the MultiVOIP where the FXS port is located. This could be the IP address of this very same MultiVOIP or another MultiVOIP. Leave the other fields blank. One entry is required for each MultiVOIP FXS port that is configured to register with Communication Manager. Click OK to accept this entry. Repeat the above steps to add additional FXS station port entries.

If the autocall feature is being used to route incoming FXO trunk calls to an extension (1000, etc.,) at the main site, you can program a second entry in the “Phones” field to 1000 to route incoming FXO trunk calls to a given FXS station to cover the autocall situation in Gatekeeper Survivable mode.

20	Multi-Tech Systems, Inc. Avaya Communication Manager Guide

Image 20

Contents MultiVOIP Configuration Guide Revision Date DescriptionContents Introduction IntroductionMultiVOIP in Avaya Communication Manager System Configuration ConfigurationChannel RTP Port Rtcp Port T38 Port Configuration Configuration Bandwidth per Channel Voice Frames per IP Packet Communication Manager MultiVOIP FXS Channels Configuration Configuration Communication Manager MultiVOIP FXO Channels Configuration = Isdn Communication Manager MultiVOIP did Channels Configuration = Isdn Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Regional Parameters screen Regional Parameter Definitions Field Name Values DescriptionRegional Parameter Definitions Field Name Values DescriptionTone Pair Values Communication Manager Settings Related MultiVOIP Setup ParametersRelated MultiVOIP Setup Parameters Version 4 Parameters Voice/Fax Parameters Channel to be configured is selected here Fax Enable Fax VolumeJitter Value Default = Mode Fax FRF 11 T.38Advanced Features Jitter Auto Disconnect AutomaticInterface Parameters Related MultiVOIP Setup Parameters FXS Not applicable to FXS interface FXO Interface Parameter Definitions Dialing OptionsFXO Disconnect On cont’d CID Number Voip Caller ID Case #4 Remote FXS call on H.323 voip system Did Options GK General Settings GK General Settings DefinitionsActivity Configuration PolicyGK General Settings Definitions cont’d RAS ParametersGatekeeper Endpoints Command Buttons Gatekeeper Calls Current Calls Field DefinitionsNumber. a sequential number for identification in the list ID alias of the endpoint originating the callCall Details Field Definitions Conference ID number CID is a unique non-zero value createdConference will have the same CID ID identifies the call with which the message is associatedTotal amount of bandwidth used by the call Type of conference request create, invite or joinLast reported state of the call Reason associated with the last state of the callH.323 alias name used to make the call E164 alias phone number used to make the callAn e-mail address used to make the call Address and port numberGatekeeper Network Parameters Network Parameter DefinitionsField Name Values Description Status Information OptionsARQ Line Hunting InformationCall Mode GK-ID Gatekeeper Services Services Screen DefinitionsField Name Values Description GK Defined Services PublicDynamic Miscellaneous MiscellaneousComm Mgr Dialing Example #1 a local station-to-station call Remote Configuration Miscellaneous MVP130-AV Rev MVP130-AV Rev aMVP130-AV-FXS Rev a MVP210-AV Rev aMiscellaneous Link Management Feature Issues Index IndexCoder field FRF11 Gatekeeper Response to field GK General Settings, RAS DID-DPO FXO Trunk Group form fields to set Dtmf Gain Unregister endpoints command Dtmf Gain High Tones