Multi-Tech Systems 410, MVP103 manual Did Options

Page 50

 

 

 

Chapter 3 – Related MultiVOIP Setup Parameters

 

 

 

 

 

 

 

DID Interface Parameter Definitions

 

 

 

 

 

 

 

Field Name

Values

Description

 

 

 

 

 

 

 

Interface

DID-DPO

Enables the customer-premises side of DID functionality

 

 

 

 

 

 

 

DID Options

MultiVOIP’s use of DID applies only for incoming DID calls. The

 

 

 

 

Start Mode used by the MultiVOIP must match that used by the

 

 

 

 

originating telephony equipment, else DID calls cannot be

 

 

 

 

completed.

 

 

 

 

 

 

 

Start Modes

Immediate Start,

For Immediate Start, the voip detects the off-hook condition initiated

 

 

 

Wink Start,

by the telco central-office call and becomes ready to receive dial

 

 

 

Delay Dial

digits immediately.

 

 

 

 

For Wink Start, the voip detects the off-hook condition. Then the

 

 

 

 

voip reverses battery polarity for a specified time (140-290 ms; a

 

 

 

 

“wink”) and then becomes ready to receive dial digits.

 

 

 

 

For Delay Dial, the voip detects detects the off-hook condition. Then

 

 

 

 

the voip reverses battery polarity for a specified time (reverse

 

 

 

 

polarity duration has wider acceptable range than for Wink Start)

 

 

 

 

and then becomes ready to receive dial digits.

 

 

 

 

 

 

 

Wink Timer

integer values,

This is the length of the wink for Wink Start and Delay Dial signaling

 

 

(in ms)

in milliseconds

modes..

 

 

 

 

Applicable only when Start Mode parameter is set to “Wink Start” or

 

 

 

 

“Delay Dial.”

 

 

 

 

 

 

 

Dialing Options

 

 

 

Inter Digit

integer values,

This is the length of time that the MultiVOIP will wait between

 

 

Timer

in seconds

digits. When the time expires, the MultiVOIP will look in the

 

 

 

 

phonebook for the number entered.

 

 

 

 

Default = 2.

 

 

 

 

 

 

 

Message

--

Not applicable to DID-DPO interface.

 

 

Waiting

 

 

 

 

Indication

 

 

 

 

 

 

 

 

 

Inter-Digit

integer values,

This parameter is applicable when digits are dialed onto a DID-DPO

 

 

Regeneration

in milliseconds

channel after the connection has been made. The length of time

 

 

Timer

 

between the outputting of DTMF digits.

 

 

 

 

Default = 100 ms.

 

 

 

 

 

 

50

Multi-Tech Systems, Inc. Avaya Communication Manager Guide

Image 50
Contents MultiVOIP Configuration Guide Revision Date DescriptionContents Introduction IntroductionMultiVOIP in Avaya Communication Manager System Configuration ConfigurationChannel RTP Port Rtcp Port T38 Port Configuration Configuration Bandwidth per Channel Voice Frames per IP Packet Communication Manager MultiVOIP FXS Channels Configuration Configuration Communication Manager MultiVOIP FXO Channels Configuration = Isdn Communication Manager MultiVOIP did Channels Configuration = Isdn Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Regional Parameters screen Regional Parameter Definitions Field Name Values DescriptionRegional Parameter Definitions Field Name Values DescriptionTone Pair Values Communication Manager Settings Related MultiVOIP Setup ParametersRelated MultiVOIP Setup Parameters Version 4 Parameters Voice/Fax Parameters Channel to be configured is selected here Jitter Value Default = Fax EnableFax Volume Mode Fax FRF 11 T.38Advanced Features Jitter Auto Disconnect AutomaticInterface Parameters Related MultiVOIP Setup Parameters FXS Not applicable to FXS interface FXO Interface Parameter Definitions Dialing OptionsFXO Disconnect On cont’d CID Number Voip Caller ID Case #4 Remote FXS call on H.323 voip system Did Options Activity Configuration GK General SettingsGK General Settings Definitions PolicyGK General Settings Definitions cont’d RAS ParametersGatekeeper Endpoints Command Buttons Number. a sequential number for identification in the list Gatekeeper CallsCurrent Calls Field Definitions ID alias of the endpoint originating the callConference will have the same CID Call Details Field DefinitionsConference ID number CID is a unique non-zero value created ID identifies the call with which the message is associatedLast reported state of the call Total amount of bandwidth used by the callType of conference request create, invite or join Reason associated with the last state of the callAn e-mail address used to make the call H.323 alias name used to make the callE164 alias phone number used to make the call Address and port numberField Name Values Description Status Information Gatekeeper Network ParametersNetwork Parameter Definitions OptionsARQ Line Hunting InformationCall Mode GK-ID Field Name Values Description GK Defined Services Gatekeeper ServicesServices Screen Definitions PublicDynamic Miscellaneous MiscellaneousComm Mgr Dialing Example #1 a local station-to-station call Remote Configuration Miscellaneous MVP130-AV-FXS Rev a MVP130-AV RevMVP130-AV Rev a MVP210-AV Rev aMiscellaneous Link Management Feature Issues Index IndexCoder field FRF11 Gatekeeper Response to field GK General Settings, RAS DID-DPO FXO Trunk Group form fields to set Dtmf Gain Unregister endpoints command Dtmf Gain High Tones