Multi-Tech Systems 410, MVP103 manual Tone Pair Values

Page 32

Chapter 2 – Configuration

The Custom Tone-Pair Settings fields are described in the table below.

Custom Tone-Pair Settings Definitions

Field Name	Values	Description

Tone Pair	dial tone, busy tone,	Identifies the type of telephony signaling tone for which
	ring tone, ‘unobtainable’	frequencies are being specified.
	tone, survivability tone,
	re-order tone
TONE PAIR	VALUES	About Defaults: US telephony values are used as defaults on
		this screen. However, since this dialog box is provided to allow
		custom tone-pair settings, default values are essentially
		irrelevant.
Frequency 1	frequency in Hertz	Frequency of lower tone of pair.
		This outbound tone pair enters the MultiVOIP at the input port.

Frequency 2	frequency in Hertz	Frequency of higher tone of pair.
		This outbound tone pair enters the MultiVOIP at the input port.

Gain 1	gain in dB	Amplification factor of lower frequency of pair. This figure
	+3dB to –31dB	describes amplification that the MultiVOIP applies to outbound
	and “mute” setting	tones entering the MultiVOIP at
	and “mute” setting	the input port. Default = -16dB
		the input port. Default = -16dB
Gain 2	gain in dB	Amplification factor of higher frequency of pair. This figure
	+3dB to –31dB	describes amplification that the MultiVOIP applies to outbound
	and “mute” setting	tones entering the MultiVOIP at
		the input port. Default = -16dB

Cadence 1	integer time value in	On/off pattern of tone durations used to denote phone ringing,
	milli-seconds; zero	phone busy, dial tone (“0” indicates continuous tone)
	value for dial-tone	survivability and re-order. Cadence 1 is duration of first period
	indicates continuous	of tone being “on” in the cadence of the telephony signal (which
	tone	could be ring-tone, busy-tone, unobtainable-tone, or dial-tone).

Cadence 2	duration in milliseconds	Cadence 2 is duration of first “off” period in signaling cadence.

Cadence 3	duration in milliseconds	Cadence 3 is duration of second “on” period in signaling
		cadence.

Cadence 4	duration in milliseconds	Cadence 4 is duration of second “off” period in the signaling
		cadence, after which the 4-part cadence pattern of the telephony
		signal repeats.

32	Multi-Tech Systems, Inc. Avaya Communication Manager Guide

Image 32

Contents MultiVOIP Configuration Guide Revision Date DescriptionContents Introduction IntroductionMultiVOIP in Avaya Communication Manager System Configuration ConfigurationChannel RTP Port Rtcp Port T38 Port Configuration Configuration Bandwidth per Channel Voice Frames per IP Packet Communication Manager MultiVOIP FXS Channels Configuration Configuration Communication Manager MultiVOIP FXO Channels Configuration = Isdn Communication Manager MultiVOIP did Channels Configuration = Isdn Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Configuration Regional Parameters screen Regional Parameter Definitions Field Name Values DescriptionRegional Parameter Definitions Field Name Values DescriptionTone Pair Values Communication Manager Settings Related MultiVOIP Setup ParametersRelated MultiVOIP Setup Parameters Version 4 Parameters Voice/Fax Parameters Channel to be configured is selected here Fax Enable Fax VolumeJitter Value Default = Mode Fax FRF 11 T.38Advanced Features Jitter Auto Disconnect AutomaticInterface Parameters Related MultiVOIP Setup Parameters FXS Not applicable to FXS interface FXO Interface Parameter Definitions Dialing OptionsFXO Disconnect On cont’d CID Number Voip Caller ID Case #4 Remote FXS call on H.323 voip system Did Options GK General Settings GK General Settings DefinitionsActivity Configuration PolicyGK General Settings Definitions cont’d RAS ParametersGatekeeper Endpoints Command Buttons Gatekeeper Calls Current Calls Field DefinitionsNumber. a sequential number for identification in the list ID alias of the endpoint originating the callCall Details Field Definitions Conference ID number CID is a unique non-zero value createdConference will have the same CID ID identifies the call with which the message is associatedTotal amount of bandwidth used by the call Type of conference request create, invite or joinLast reported state of the call Reason associated with the last state of the callH.323 alias name used to make the call E164 alias phone number used to make the callAn e-mail address used to make the call Address and port numberGatekeeper Network Parameters Network Parameter DefinitionsField Name Values Description Status Information OptionsARQ Line Hunting InformationCall Mode GK-ID Gatekeeper Services Services Screen DefinitionsField Name Values Description GK Defined Services PublicDynamic Miscellaneous MiscellaneousComm Mgr Dialing Example #1 a local station-to-station call Remote Configuration Miscellaneous MVP130-AV Rev MVP130-AV Rev aMVP130-AV-FXS Rev a MVP210-AV Rev aMiscellaneous Link Management Feature Issues Index IndexCoder field FRF11 Gatekeeper Response to field GK General Settings, RAS DID-DPO FXO Trunk Group form fields to set Dtmf Gain Unregister endpoints command Dtmf Gain High Tones